Filter Results By:
Products
Applications
Manufacturers
Earth Bond
Checks a ground circuit's ability to handle fault current in the event of insulation failure.
-
product
Electrical Safety Test Equipment
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
product
Earth Bond Test Set
EC-12
The Earth bond test is a basic safety test prescribed in many standards to test samples for the integrity of earthing continuity throughout the sample.
-
product
Safety Test Panel for Geyser
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of Geyser. In addition to the conventional safety tests, test for performance is also included.
-
product
Medical System
Sentinel I
Chroma Systems Solutions, Inc.
The Sentinel I System provides fully automated Electrical Safety Testing to IEC/EN/UL/CSA 60601-1. This system is ideal for testing medical products with one or no patient connections or low volume production where operators can manually change leads between different patient connections. This is a 5 in one Hipot test system that can test Hipot, Ground Bond, Insulation Resistance, Patient Leakage, Earth Line Leakage, Enclosure Leakage and Patient Auxiliary Leakage.
-
product
Safety Test Panel for Water Cooler
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of washing machines. In addition to the conventional safety tests, test for performance is also included.
-
product
Electrical Installation Testers
Continuity tester for measuring the resistance of the protective earth conductors and earth bonds – an ohmmeter dedicated to electrical safety
-
product
Ground Bond Tester,
266
Our 266 Model makes Ground Bond / High Continuity Testing simple with 60 Amps of current to satisfy your toughest NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 266 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
product
Manual Ground Bond Tester
HYAMP
Patented CAL-ALERT® functionElectronic Dwell4-wire measurement and milliohm offsetPatented VERI-CHEK® functionStorage of up to 10 setups with 3 steps per setupBuilt-in Security settingsMinimum and maximum trip settingsInterconnect to Hypot® III to form a complete test systemBuilt-in security settingsLine and Load regulation
-
product
Bond Testing
Our complete line of bond testing (BT) flaw detectors provides unmatched capabilities for the location of discontinuities and other flaws in composite structures. We offer a wide range of measurement features and application-specific options for flaw detection.
-
product
Multimode Bond Tester
BondMaster 600
The BondMaster® 600 delivers a powerful combination of multiple mode bond testing software and highly advanced digital electronics, providing consistently crisp and high-quality signals. Whether you are inspecting honeycomb composite, metal-to-metal bonds, or laminate composite, the BondMaster 600 offers exceptional ease-of-use thanks to its direct-access keys and streamlined interface that features convenient presets for common applications.
-
product
Earth Tester
TAURUS PRECIOHM ET
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
product
Earth and Resistivity Testers
Earth tester offering selective earth, soil resistivity, earth coupling and continuity measurements
-
product
Earth Resistance Tester
HT5600 / 700
Wuhan Huatian Electric Power Automation Co., Ltd.
Suitable for telecommunication, electric power, weather, machine room, distribution line, transmission line, gas station, factory, lightning rod, etc.
-
product
Earth Resistance Testers
Earth Resistance Tester is widely applied in ground resistance measurement, loop resistance measurement in fields such as electric power, telecommunications, meteorology, oil field, architecture and industrial electrical equipment, etc. When measuring ground system with loop, there is no need to disconnect the ground wire without auxiliary electrode, which means safer and faster.
-
product
Earth Resistance Testers
Shanghai Beha Electronics Co., Ltd.
A handy test and measurement instrument for testing Earth resistance and Soil resistivity.
-
-
product
Earth Resistance Tester
2678
Shenzhen Chuangxin Instruments Co., Ltd.
RK2678 series Earth Resistance Tester is used to measure the grounding resistance of the electrical equipments’ internal. It’s suitable for measuring the ground wire resistance of the various motors, electrical appliances, instruments and meters, household appliances and other equipment enclosure etc.
-
product
Post Wire and Die Bond Inspection Machine
IV-E1700
IV-E1700 is a post wire and die bond inspection machine that is known for having a proven, effective and patented 2D+3D Inspection system. This product is best used to weed out defects with data collection for process improvement and reports for SPC quality Control.
-
product
Earth Ground Testers
TES Electrical Electronic Corp.
Capable of measuring earth voltage. Data hold function. Auto power off function. The timer operates automatically about 10 minutes with the "test button switch are pressed to keep the tester power on.
-
product
Clamp Type Earth Resistance Tester
ETCR2000 / 730
Wuhan Huatian Electric Power Automation Co., Ltd.
Widely used in electric power, telecommunications, meteorology, oil fields, construction and industrial electrical equipment, such as grounding resistance measurement, circuit resistance measurement.
-
product
Digital Earth Resistance Tester
8PK-ST1520
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
-
product
Bond Inspection
Increasingly thin wires, finer pitches, as well as more applications of thick wire for higher capacities are among the current trends in wire bonding. At the same time, the requirements for robust and defect-free bonds are increasing, for example in assistance systems in the automotive sector and in RF modules in the 5G mobile communications network. This makes reliable inspections extremely important.
-
product
Bond Testers
Royce bond testing systems can handle a variety of testing applications including wire bond pull testing, wire bond ball shear testing, BGA ball shear testing, die shear testing, and high speed ball shear testing.
-
product
Earth Resistance Meter
MTD20KWe
The MTD-20KWe digital earth tester allows for the measurement of Earth Resistances and Soil Specific Resistivity, and also the spurious voltages caused by parasitic voltages present in the soil.
-
product
4 Wire Earth Resistance Testers
2734 ER
Standard Electric Works Co., Ltd
● Microprocessor-controlled with advanced safety features.● 4-wire testing only.● Automatic C spike check.● Auto power-off.● Auto data hold.● Large LCD (2000 counts).● Protective terminal cover.
-
product
Post Wire and Die Bond Inspection Machine
IV-T3300
IV-T3300 is a post wire and die bond inspection machine with Dual JEDEC Tray Feeder System. It features a large inspection area of 600x500mm and a quick trays change of 5-7 seconds.
-
product
3 Wire (Digital) Earth Resistance Tester
1820 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
product
Bond Testers
Has automated the test process with microprocessor-controlled data acquisition. Designed to provide the expected internal bond strength for various types of paper, coated products and paperboard, this instrument measures the impact energy imparted to the specimen. The machine consists of a base, sample-preparation press, tape dispenser, dual-range pendulum (0 to 0.325 ft. lbs. and 0 to 0.650 ft. lbs.) and Digital Display. Internal Bond software is available.
-
product
Aeronautical Ground Earth Station Emulator
GES
Square Peg Communications Inc.
Ground Earth Station (GES) emulator provides a simple and flexible means of testing the operation of Aeronautical Earth Stations (AESs) and end-to-end applications for the Inmarsat Classic Aero service, without the expense of airtime charges. It can be used to test basic AES functionality, including Aero I/H+ and Aero H voice calls, and data transfer applications such as ACARS.
