Filter Results By:
Products
Applications
Manufacturers
Emission
particles emanating from a source.
See Also: Acoustic Emission, Gas Emission, Radiated Emissions, Conducted Emission, Emission Reference Sources
-
product
SF6 Optical Gas Imaging Camera
FLIR GF306
The FLIR GF306 optical gas imaging camera visualizes sulfur hexafluoride (SF6) and other gas emissions without the need to shut down operations. SF6 is used in the electric power industry as an insulator and quenching medium for gas-insulated substations and circuit breakers. The portable, non-contact GF306 allows you to quickly scan substations for leaks while maintaining a safe distance from high-voltage equipment. By catching leaks early, the GF306 reduces lost revenue to breakdowns and repairs.
-
product
Chassis Dynamometer Smoke Testers
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
product
Ancillaries - Radiated
EMC emissions can be at very low signal levels and pre-amplifiers can help to improve S/N ratio. The low level of emission signals can make them difficult to identify in noisy environments. RF filters are designed to attenuate the major sources of noise, thus making the task of measurement easier.
-
product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
product
Open-Path Chemical Detection System
LaserWarn™
Block Engineering's LaserWarn is an open path gas detection system based on patented quantum cascade laser technology. LaserWarn detects chemical threats, leaks, and fugitive emissions over a coverage area of thousands of square feet, and can be used in both indoor and outdoor applications.
-
product
ICP-OES Analyzer
ARCOS
SPECTRO Analytical Instruments GmbH
For the most demanding elemental analyses in industry and research. ARCOS analyzer represents a new pinnacle of productivity and performance for inductively coupled plasma optical emission spectrometers. SPECTRO ARCOS excels in industrial and academic applications for the most advanced elemental analysis of metals, chemicals, petrochemicals, and other materials.
-
product
Radiated Emission
High accuracy CISPR 16-1-1 EMI receivers and high precision calibrated antennas for radiated emission measurements.
-
product
High-resolution Spectrometer
HR4000
Our next-generation high-resolution spectrometer is a novel combination of optics and electronics that is ideal for applications such as characterizing lasers, measuring gas absorbance, and determining atomic emission lines.
-
product
Spiral Antenna
UHF Spiral antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in the monitored asset. It is a broadband antenna with a flat response which makes Spiral antenna suitable in a number of different applications. It has been optimized to operate in a frequency range typical for PD activity and it was designed to provide maximum sensitivity and high gain.
-
product
Emission Analyzers
The VLT-E8104 emission analyser measures the opacity of the exhaust gases of vehicles with petrol/LPG/CNG engines. The accuracy complies with OIML class 0. An oil temperature sensor and an rpm counter can be connected.If you connect diesel smoke cell VLT-E9210, this analyser is a fully functionsl diesel smoke analyser as well.
-
product
General Purpose L-Chassis Single Output Power Supplies
Series RTW
Kepco's RTW series are general-purpose, L-chassis, single output power supplies.They are available in 50, 100, 150 and 300-watt power levels. Their small size and very low profile allow the RTW to be fitted into small spaces. They feature full safety compliance to international standards and have suppressed both conducted and radiated emission to FCC class B levels.
-
product
Scanning Electron Microscopy
SEM
Materials Evaluation and Engineering
JEOL JSM-6610 LV LaboratoryScanning electron microscopy (SEM) uses electrons for imaging to obtain higher magnifications and greater depth of field than light microscopes. The instruments at MEE are capable of variable-pressure, or low vacuum, SEM (VPSEM), as well as traditional high-vacuum conditions for sample observation. VPSEM is a specialized method using a variable-pressure sample chamber that allows direct evaluation of samples that are not readily examined with a traditional high-vacuum SEM. Nonconductive or vacuum sensitive samples that would typically require additional sample preparation can be directly analyzed in VPSEM without the need for additional sample preparation, such as carbon or metallic conductive coatings. This reduces both sample preparation time and distractions in microanalysis. Our laboratory also has a field emission SEM (FESEM) for critical high-magnification work and low-voltage (LVSEM) applications. Each instrument has a spacious sample chamber that can accommodate large and irregularly-shaped specimens and accessories for feature dimensional analysis and chemical microanalysis.
-
product
Continuous Gas Analyzer
CT5400
Multi-component continuous gas analyzer combines QCL and TDL technologies in a single rack mount enclosure to measure process gas and monitor emissions from sub ppm to % levels. The CT5400 is ideal for measuring NOx, SO2, CO, CO2, CH 4, NH3, O2, HCl and other combustion gases identified as pollutants, ozone depleting, or responsible for global warming.
-
product
Radiation (EMF, Nuclear, RF)
Sper Scientific radiation meters measure EMF, Nuclear, and Microwave radiation levels. Whether you are, measuring the RF strength of Wi-Fi and LAN network, or the electromagnetic field emissions from electrical power lines and transmission equipment, computers, HVAC, audio/video, and other electrical appliances. Our meters are small and light enough to go anywhere, yet sensitive enough to detect minuscule amounts of gamma, beta or X-rays.
-
product
Total Hydrocarbon Analyzer
Model 4030
Teledyne Analytical Instruments
The Model 4030 uses a field proven FID detector in a heated chamber. The chamber is heated to a high temperature to meet US EPA requirements for VOC emissions monitoring.
-
product
Acoustic Emission Testing Equipment
1283 USB AE Node
The 1283 USB AE Node is a full-featured, low-cost Acoustic Emission testing equipment that plugs conveniently into and is powered by the USB port of a user’s PC or laptop to maximize portability and versatility.
-
product
IC Measurement Technology
Emission
is used to measure conducted emissions (measurements with direct 1 Ohm/150 Ohm-coupling) according to IEC 61967-4 at IC pins.
-
product
VOC Emissions Testing for Electronic Equipment
Underwriters Laboratories Inc.
Product emissions testing on electronic equipment, including printers, consumer electronics, information and communications equipment, and appliances.
-
product
Continuous Emission Monitoring Systems
TML has more than 50 years' experience designing, manufacturing, and supporting continuous emission monitoring systems (CEMS). We have a team of experienced CEMS air quality experts that will thoroughly review your process and operating permit and recommend the most cost effective and reliable solution for monitoring the gases of interest. TML's continuous emission monitoring systems are based on rugged, reliable equipment manufactured to exact standards. The result is products and systems with some of the highest mean time between failure rates in the industry. Whether it's a standard or custom solution, we stand behind our products 110%, guarantee CEMS certification, at least 95% uptime, replacement parts, and 24 x 7 support. We offer a total CEMS solution including data acquisition software for recordkeeping and reporting, lower cost of ownership, superior product reliability and designed for simple and easy maintenance.
-
product
Measurement Technology for Teaching and Training
Is particulary suitable for training and further education. With the disturbance emission model, a variety of different experiments which improves one`s understanding of electromagnetic processes in modern electronic engineering are possible. The coupling mechanisms of disturbance emissions are visualized from their sources to the antenna. The impacts of EMC measures are then easier to understand. At VM 251 the electromagnetic d
-
product
Acoustic Emission Calibrator
AE calibrator is similar to a simple signal generator, it can generate a variety of controlled waveform signal, different types, different amplitude and different frequency. It can help users calibrate acoustic emission detection equipment before acoustic emission detection.
-
product
Plasma Emission Controller
RU-1000
The optical technology developed by HORIBA and the gas control technology offered by HORIBA STEC have been combined to make further advances in plasma control technology. The plasma emission controller RU-100 offers; faster deposition by controlling the transition region, optimized distribution in a large-area, high-capacity chamber, plasma stabilization in a long sputtering process (stable deposition), and mixture optimization of compounds for reactive sputtering.
-
product
Automotive Oxygen Sensor
Model R-22A
Teledyne Analytical Instruments
Teledyne has a long and successful history in the development and supply of oxygen sensors for automotive emission testing equipment.The “R” series sensors are used by most automotive emission equipment manufacturers worldwide. We are striving to improve our sensors through aggressive research and development, assuring the highest quality products offered by any supplier of oxygen analyzers.
-
product
Railway EMC Testing
EMC Technologies is the only NATA accredited organisation for performing Track side testing of the whole train/tram. We can provide NATA accredited testing services to EN 50121-3-1, EN 50121-3-2, EN 50121-4 and EN 50121-5. This includes electromagnetic emission and electromagnetic immunity measurements. We can also provide testing and consultation for EN 50121-1 and EN 50121-2 .
-
product
EMI EMC test Solutions for Emission
Scientific Mes-Technik Private Ltd
EMI EMC test Solutions for Emission
-
product
Hardware Enabled SaaS Solution Quantifying Methane Emissions
MethaneTrack™
NevadaNano’s MethaneTrack™ is a low cost network of rugged monitoring points to measure methane emissions and report leak location and size to the operator. Utilizing an Industrial IoT (IIoT) network to detect methane in the air, MethaneTrack™ detects fugitive and operational emissions from a site and immediately alerts the operator of the location and volume of the emissions, facilitating rapid response and repair. Autonomous, continuous monitoring enables up to 99% reduction in emissions while reducing operational costs and boosting profits.
-
product
Engine Exhaust Particle Sizer
3090
The Engine Exhaust Particle Sizer 3090 (EEPS™) spectrometer measures the size distribution of engine-exhaust particle emissions in the range from 5.6 to 560 nm with the fastest time resolution available. Users can visualize and study the dynamic behavior of particle emissions that occur during transient test cycles, during the first few seconds of a cold start, or during regeneration of a particle trap or diesel particulate filter (DPF).
-
product
CX4000 – FTIR Gas Analyzer
Gasmet CX4000 is an industrial multi-component FTIR gas analyzer for continuous emission monitoring applications, integrated into a Continuous Emissions Monitoring system (CEMS II e). It can be used to measure up to 50 components simultaneously, and additional gases can be easily added without any hardware changes. The corrosion-resistant sample cell is heated up to 180 °C, which makes CX4000 an ideal tool for analyzing trace concentrations of pollutants in wet, corrosive gas mixtures.
-
product
Air Quality Analysis
Ambient Gas Monitoring: We offer a variety of analyzers for the ambient monitoring of the criteria pollutant gases, including CO, NOX, SO2, and others such as CH4 and CO2. Source Gas Monitoring (Emissions Monitoring): Experience reliable measurement in your process for emissions compliance every time.Ambient Particulate Monitoring: Experience our monitoring technology and gain the power to do more than just inform.Emissions Calibrators: For continuous monitoring of mercury in exhaust stacks, waste incinerators, and cement kilns, or multi-gas models to control the calibration of gas concentrations.
-
product
Combination Emissions Tester on Trolley for the Measurement of Diesel- and Petrol-Powered Vehicles - Low Weight, Short Warm Up Time
MCT T | VP 135225
Maschinenbau Haldenwang GmbH & Co. KG.
The combination tester on trolley is designed for the measurement of petrol- and diesel-powered vehicles. In addition, low weight, compact design and short warm-up time ensure easy handling.
