Filter Results By:
Products
Applications
Manufacturers
- Frequency Devices Inc.
product
Band Reject (Notch) Filter Components
precision band-pass and band reject (notch) active filters that provide high performance in a compact 32-pin DIP package, with a broad range of fixed center frequencies (fo) from 1 Hz to 100 kHz. Each filter type features a neartheoretical amplitude/phase response along with lowoutput voltage noise enabling these filters to achievea 10,000:1 or better dynamic signal range.
-
product
Ku Band Gain Control Amplifier
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
product
Satellite Trunk Interception System
Satellite trunks in the X, C, Ka, Ku bands carry enormous information, the interception of which can assist LEAs with real-time analysis of data transmitted over these links. Our solutions are customizable and scalable (Bands and protocols) based on the customer's needs.
-
product
MICROWAVE TUBES
High reliability dispenser cathode technology (up to 90,000 hrs operation achieved for S band Watchman ATC radar)European “Centre of Excellence” for cathode and electron gun designIn-house cathode technology minimising reliance on ITAR controlled partsFast warm (under 3 seconds) versions available in Ku bandEmission testing and surface analysis facilities in-houseAir, land and sea platforms supported
-
product
Fixed GEO Earth Stations
Kratos Defense & Security Solutions, Inc.
Kratos provides a broad range of fixed earth stations ranging from 3.5m to 18m and configured in receive-transmit or receive-only mode. These antennas offer outstanding electrical performance and exceptional versatility to support low PIM at certain Ku bands and all X-band systems.
-
product
Signal Level Meter
XR-3W+
From satellite dish alignment, to UHF off-air antenna pointing, to cable TV MER measurements, the XR-3 is the meter for you! The XR-3 is the most capable meter offered by Applied Instruments. It's more durable than the popular Super Buddy meter, and has added features and performance. The XR-3's modular design with field swappable modules provides wide versatility to fit different measurement applications, including DBS satellite (i.e. Dish Network, DIRECTV, Bell TV, Shaw Direct), VSAT satellite (i.e. iDirect, Hughes Ku band, and more), VHF/UHF off-air (analog and ATSC digital), and CATV (QAM and analog). The XR-3 is great for installing and troubleshooting DISH SmartBox, Blonder Tongue, and other SMATV headend systems often used in hotels, multi-dwelling units, and institutional facilities. Modular Test Instrument. Satellite Finder. Installer Signal Meters. CATV Analyzer. Modules.
-
product
Precision Programmable Attenuator
RCDAT-30G-30
Mini-Circuits’ RCDAT-30G-30 is a precision programmable attenuator covering an extremely wide bandwidth, from 0.1 to 30 GHz. Its unique design allows attenuation settings to be programmed from 0 to 30 dB, in 0.5 dB steps with monotonic attenuation change per dB, even at the highest frequencies and attenuation settings. The attenuator can be controlled via USB or Ethernet, allowing control directly from a PC, or remotely over a network. VHF / UHF / L / S / C / X / Ku / K band testing.
-
product
Waveguide Electromechanical Relay Switches
Pasternack's waveguide electromechanical relay switches offer full waveguide performance covering C, X, Ku, K and Ka frequency bands. Waveguide electromechanical relay switch components from Pasternack cover various frequency ranges from 5.85 GHz to 40 GHz depending on the model. These waveguide switches are ideal for applications that include electronic warfare, electronic countermeasures, microwave radio, VSAT, SATCOM, radar, research and development, space systems and test instrumentation.
-
product
Test Loop Translators
This high performance test loop translator is intended for use in professional applications in Ku band such as satellite earth stations.
-
product
Waveguide Electromechanical Relay Switches C, X, Ku, K & Ka Bands up to 40 GHz
Waveguide Electromechanical Switch models cover C, X, Ku, K, Ka frequency bands up to 40 GHz. SPDT and Optional DPDT* Configurations with Latching Self Cut-Off Actuators, TTL Logic, and Position Indictors with manual override. Patented Motor Drive with Arc Suppression. Designs support WR-137, WR-112, WR-90, WR-75, WR-62, WR-42, and WR-28 waveguide sizes with O Rings for pressurized operation. Power handling capability up to 12 kW CW and 320 kW Peak. These waveguide electromechanical relay switches deliver desirable performance that includes high isolation levels up to 105 dB, and extremely low insertion loss down to 0.01 dB.
-
product
Rackmount or compact airborne state of the art Solid State Power Amplifiers
SSPAs
Broadband off the shelf or custom designed RF/Microwave SSPAs as airborne baseplate miniature modules or as 19" 3U compact rackmount AC units, CW or Pulsed operation from 100W to 1KW up to Ku frequency band.
-
product
Band Pass Filter
PA72BPF
The PA72BPF daughter board is an additional filter board. It typically contains two selectable differential 3rd order elliptic band pass filters. These filter modules are tailored by Applicos to the customers’ requirements. The filters can be used to filter the output signal of the generator daughter boards to achieve an even better distortion and noise suppression.
-
product
Full Band Down-Converters
STC-20-10-S1
Full band down-converters are designed to convert high frequency millimeterwave signals down to the baseband at 10 MHz to 1.6 GHz. These down-converters deliver a superior performance since they are assembled with SAGE Millimeter’s instrumentation grade components, such as multipliers, amplifiers, filters, isolators, and more. The below standard offering covers the frequency range of 26.5 to 170 GHz and delivers a typical LO power of 3 dBm and conversion gain of 20 dB. The down-converters provide low harmonic levels and excellent gain flatness, making them ideal for test instrumentation applications. Specifications other than those listed below are available upon request.
-
product
Broad Band Amplifiers
Broad band amplifiers (A.K.A. wide band) from Fairview Microwave provide amplification for radio frequencies in broadband. Our broad band amplifiers applications include: military / defense, test instrumentation, EW/ECM, radar, satcom, telecom, microwave radio and various industrial RF, microwave and millimeter wave applications. Fairview broad band amplifiers have a maximum frequency as high as 18 GHz depending on the amp configuration.
-
product
Narrow Band Multiplier
*no mechanical tuners*fullband operation*planar design*bias voltage required
-
product
Return Band Alignment System
6103/6106
Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106).
-
product
Narrow Band Filters (Single Octave)
MAXI-POLE® Series
The MAXI-POLE® Series of tunable filters provides improved passband performance (reduced insertion loss for a given bandwidth) in a slightly larger package. The product line includes several standard designs in various frequencies to support almost any application. Approximate performance is summarized in the Maxi-Pole Series Selection Guide.
-
product
Band Pass Filters
VDI offers up-converter modules for communication applications. The double sideband nature of the up-converter modules makes filtering necessary. VDI has designed filters to filter one sideband and preserve signal modulation. These filters offer low passband insertion loss and high out-of-band rejection. Custom filters may be available upon request. NRE (non-recurring engineering) fee may be required.
-
product
Polarization Maintaining Band Pass Filter
Zhongke Rayzer Optical Technology Co.,Ltd
Selects the thin film filter withgood performance to ensure the high quality opticalperformance, stability and reliability. It is uses to shieldnoise signal in EDFA and fiber laser system. It has thecharacteristics of high isolation, low insertion loss, highreturn loss and high power.
-
product
Wide Band Filters (multi-octave)
GEN3-ERF®
The 3rd Generation Mini-ERF is a Reduced SWaP-C, 30 to 520 MHz tunable bandpass filter that features 50mW (typ.) power consumption, 1 Watt CW continuous power handling (7% BW), +40 dBm IIp3 (typ.), low insertion loss, and 4 dB typ. selectivity @ +/-10%, (7% filter). The GEN3-ERF’s are fully tuned and tested by Pole/Zero® for convenience and ease of use.
-
product
Band Pass Filters
High-Pass (HPF series), Low Pass (LPF series) and Band Pass (BPF series) Filters are available, providing desired skirt selectivity and rejection levels with minimum insertion loss in the pass band. The filters are offered in all standard waveguide bands covering 18 to 400 GHz depending on our possibility to fulfil the customers' requirements. Dimensions of filters depends on required specifications. .
-
product
C/Ku Band Satellite Monitoring
SCL-3412
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
product
Band DWDM EDFA
MSA Module C
Amonics now packages one of its most popular product lines, C-band DWDM Erbium-doped Fiber Amplifiers (EDFAs), into standard MSA size. The same reliable, stable and durable EDFAs are thus readily available for system integration of a wider range of applications. The devices provides the usual alarms and status indicators, with an integrated RS232 computer interface for easy control, diagnostic functions and data acquisition. This MSA series will be expanded to cover EDFAs of different specifications in our product range in order to meet the growing demands.
-
product
Narrow Band Filters (Single Octave)
IMF™ Series
The Integrated Microwave Filter or IMF™ Series introduces accelerated tuning speeds packed in a very small, lightweight filter, providing maximum sensetivity and improved system performance for cleansing your ESM environment. Designed for the military radar market, specifically Active Electronically Steered Arrays (AESA) Radars and Phased Array Radars but compliment a broad range of applications such as; Commercial, Tactical & Military Communications, RF Front Ends (RFFE’s), SATCOM-on-the-move (SOTM), along with Electronic Warfare & Radar applications.
-
product
O Band Tunable Laser Source
CA9812
The CA9812 O Band tunable laser integrates a widely tunable laser with a semiconductor optical amplifier (SOA). The tunable laser is electronically tuned and can address any wavelength from 1265.00 nm to 1365.00nm. The integrated SOA facilitates flexible control of the output power and acts as a shutter when reverse biased, enabling dark tuning between channels. The device is packaged into a standard module box package, with an ternal optical isolator and a polarization maintaining fiber output.
-
product
Wide Band Transcorders
WBT Series
A fully self-contained RF recording and playback system. A single unit can record up to 40 MHz of RF spectrum between 50 MHz and 6 GHz. The recorded data is streamed to a high-speed, internal 1TB solid state drive. The data files are an industry standard open format VRT and can be played back anywhere within the same tuning range at the same recorded power level without additional equipment.
-
product
L Band Splitter, DC Block All Ports
PD5032
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
product
Antenna, Octave Band Horn
EM-7022 | 4 GHz – 10 GHz
Electro-Metrics offers three horn antennas, each covering an octave bandwidth from 1 to 10 GHz. The horns are individually calibrated and can be used for either receiving or transmitting applications. They are especially suited to radiated immunity testing and can be used to generate fields in excess of 200 Volts/meter. All three horns feature type “N” connectors and exhibit low VSWR to ensure compatibility with power amplifiers.
-
product
L Band Splitter, DC Block All Ports
PD5062
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy Type N Female (Jack) Low PIM
-
product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
product
Narrow Band Filters (Single Octave)
POWER-POLE® Series
The POWER-POLE® Series of tunable filters provides improved RF performance with increased power handling capability and the lowest insertion loss for a given bandwidth. The product line includes several standard designs in various frequencies to support almost any application. Approximate performance is summarized in the POWER-POLE Series Selection Guide.
