Filter Results By:
Products
Applications
Manufacturers
LED Sources
emit light as a reference or to illuminate.
See Also: Light Sources, Optical Light Sources
- Applied Instruments, Inc.
product
RF Noise Source
NS-3
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
product
Non-Contact H.V. Detector
278 HP
Standard Electric Works Co., Ltd
● Protection class : IP65.● 3 LED indicators in a circle for easier viewing in any directions (360° LED indication).● 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV● Bright LED visual indication● Frequency range: 40~70Hz● Longer hood makes LED indicators more visible● Audible indication● Easy-to-prove method.● Self-test function● Power source : 1.5V "C" type battery × 3● High impact nylon casing.● Non-contact detection by proximity● Compatible with most hot sticks.● Lightweight, robust & compact.● Suitable for indoor and outdoor use.● Easy access to batteries.● Special ranges are available upon request. ● The maximum detection range can be 500kV.● Meets EN 61326-1 CISPR 11 EN 61000-4-2 EN 61000-4-3 EN 61000-4-8
-
product
Long Light Source
LM-A
The long light source is compatible with the LM-101 or the LMC-20. The light is supplied with a 50 watt tungsten halogen convection cooled light source which provides suffcient energy for use with narrow band pass filters or monochronomators in the wave length range of .35 to 2.5 microns. The light beam is chopped at 200 hz by a quiet, vibration free, synchronous motor. The housing also contains a secondary LED light source and detector for synchronization of the amplifier, plus an electro-mechanical shutter to block the light output when the instrument is zeroed. An internal collimating lens produces a narrow beam (<1") so the LM-A can be used in bell-jar and large coating systems.
-
product
Temperature Calibrator
Model KM-CAL-906
Kusam Electrical Industries Limited
This temperature Calibrator gives high accuracy of 0.02% for measure and source. It has dual display, 5 digits for measure and 6 digits for source & white LED for backlight. Volts, RTD & Thermocouple. It gives output up to 500W to 5kW and output for calibrating R, S, K, E, J, T, N, B, L, U type of Thermocouples RTD & Continuity.
-
product
Measuring System for Assessment of Optical Radiation Safety
IEC62471
The system is designed especially for the determination of optical radiation hazard exposures specified in IEC62471, such as actinic UV hazard exposure for the skin and eye, near-UV hazard exposure for the eye, retinal blue light hazard exposure, retinal thermal hazard exposure, thermal radiation hazard for eye and skin, for LED products, UV-Lamps, lighting sources, luminaires and etc.
-
product
Spectroradiometer
SpectraScan® PR-745
The SpectraScan® Spectroradiometer PR-745 is JADAK’s enhanced sensitivity portable solution for spectral based photometric and colorimetric light measurements, designed for applications requiring precise light measurements from a range of light sources, such as display monitors and projectors, reflective surfaces, and industrial applications (visual display testing, LED testing, film and video post-production, auto/aerospace displays, and dental color testing).
-
product
Non-Contact H.V. Detector
300 HP
Standard Electric Works Co., Ltd
● Protection class : IP66.● 3 LED indicators in a circle for easier viewing in any directions (360° LED indication).● 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV.● High bright LED visual indication.● With the longer shelter to make the 3 LED indicators brighter under the sun.● Sound indication.● The maximum voltage setting can be 500kV .● Self-test function.● Power source : 1.5V "C" type battery × 3.● High impact nylon casing.● Non-contact work by proximity.● Compatible with most hot sticks.● Lightweight, robust & compact. ● Suitable for indoor and outdoor use.● Easy access to batteries.● Special ranges are available upon request. ● The maximum detection range can be 500kV.● Meets EN 61326-1 CISPR 11 EN 61000-4-2 EN 61000-4-3 EN 61000-4-8
-
product
Turn Key Laser and LED Sources with Picosecond Pulse and Repetition Rate up to 100 MHz
DeltaDiode
DeltaDiodes utilize laser diode and LED technology to generate short optical pulses over a very wide range of repetition rates and wavelengths. Optical pulses as short as 50ps can be generated at repetition rates up to 100MHz.
-
product
Absorption Probe
ASD12-N
The ASD12-N absorption probe has a durable LED light source for direct installation into laboratory bioreactors and disposable bioreactors for measuring cell growth and optical density. The probe is available in three different lengths to fit any vessel and is suited for sterilization / autoclaving procedures.
-
product
MPI Testing Solution
Since 2008, MPI’s LED tester has provided optical and electrical measurements. With mass production experience, tester functions include flexible recipe management, accurate calibration, and statistical analysis. Flexible configurations allow the customer to choose test equipment configurations from the spectrum meter, photo detector and source measurement unit in accordance with your specific requirements. With accurate controlling of each instrument and intelligent data analysis, our testers offer the most accurate measurement result for a wide variety of optical devices.
-
product
Imaging Luminance Meter
CX1000
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
CX-1000 imaging brightness meter is used to measure the brightness, brightness distribution and uniformity of LED modules, lamps, lamps, displays, street brightness and other light sources.
-
product
Spectroradiometer
SpectraScan® PR-670
The SpectraScan® Spectroradiometer PR-670 is JADAK’s enhanced economical portable solution for spectral based photometric and colorimetric light measurements, designed for applications requiring precise light measurements from a range of light sources, such as display monitors and projectors, reflective surfaces, and industrial applications (visual display testing, LED testing, film and video post-production, auto/aerospace displays, and dental color testing).
-
product
Remote Sensors
The most versatile and popular sensors we make. The ROS-W (Remote Optical Sensor with tinned wire termination) and ROS-P (Remote Optical Sensor with 1/8" phone plug termination) are threaded stainless steel remote optical sensors with a visible red LED light source. All these sensors have the "on-target" green LED indicator
-
product
Incoherent Sources
Our Incoherent Sources include unmounted LEDs, mounted LEDs, collimated LEDs, LED light sources, superluminescent diodes, and broadband light sources. Our collimated LEDs are particularly popular and are compatible with many microscopes. Versions are available with center wavelengths from the UV into the NIR or that emit white light.
-
product
Spectroradiometer
SpectraScan® PR-740
The SpectraScan® Spectroradiometer PR-740 is JADAK’s enhanced sensitivity portable solution for spectral based photometric and colorimetric light measurements, designed for applications requiring precise light measurements from a range of light sources, such as display monitors and projectors, reflective surfaces, and industrial applications (visual display testing, LED testing, film and video post-production, auto/aerospace displays, and dental color testing).
-
product
Fiber Optic Light Sources
Fiber optic light sources are a necessity for performing optical fiber network testing to measure the optical fiberal loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the optical fiber power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the optical fiber power meters, they act as an economic and efficient solution for the optical fiber network works.
-
product
2x16 Channel Multiplexer
FXA-103 MUX 16×2
The FXA-103 is a two times sixteen channel multiplexer which allows to route analog or digital input signals from multiple sources to one measurement device. To simplify control the corresponding relays of both multiplexers are switched together and each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
product
Non-Contact H.V. Detector
380 HP
Standard Electric Works Co., Ltd
● Protection class : IP65.● 7 voltage settings : 120V, 4kV, 15kV, 25kV, 35kV, 46kV, 69kV● Bright LED visual indication● Vibration function● Frequency range: 40~70Hz● Audible indication● Easy-to-prove method● Power source : 9V rechargeable battery● Can be charged with the automotive● Non-contact detection by proximity● Compatible with most hot sticks● Lightweight, robust & compact● Special ranges are available upon request● Flashlight function● Safety standard : EN 61326-1 CISPR 11● Operating temperature and humidity : 0°C ~ 40°C / 80% R.H. Max. ● Dimensions: 262(L) × 85(W) × 56(D)mm● Weight: Approx. 330g
-
product
Fibre Tracer
FT20
The KD Optics FT-20 is a small, hand-held, visible source used for tracing multimode fibre optic cables and is especially useful for identifing a single fibre in a multi-fibre cable. The unit has a bright LED output with a 2km range and is modulated at 2Hz.
-
product
High Precision Rotation Luminaire Goniospectroradiometer
LSG-1800BCCD
LSG-1800BCCD Goniospectroradiometer is high precision automatic goniophotometric instrument for luminous intensity distribution measurements with facility for turning the light source. The LSG-1800BCCD can do the spatial CCT test when do the intensity distribution test. It is for industrial laboratory measurements the photometric data of luminaires such as LED luminaries, HID lamps, fluorescent lamps and so on.
-
product
4 CH LED Driver
LED-0401
UC INSTRUMENT’s LED-0401 Compact 4 Channel Computer-Controlled Universal LED Drivers are designed to drive a broad range of LED light sources. Maximum 1.5Acurrent can be output to each channel.
-
product
Non-Contact Voltage Tester w/ LED Flashlight
LVD1A
Non-contact AC voltage detector and LED flashlight combined in one convenient, compact design. With exclusive dual-sensitivity. The voltage detector glows blue when it's near AC voltage, and glows red when it's at the source.
-
product
Total Luminous Flux Measurement System
This system enables the total luminous flux measurement of luminous intensity distribution 2 and 4 light sources based on the measurement standards of LED lightings LM-78 and LM-79 approved by IESNA (Illuminating Engineering society of North America) .
-
product
LED
light-emitting diode (LED) is a two-lead semiconductor light source. It is a pn junction diode, which emits light when activated. When a suitable voltage is applied to the leads, electrons are able to recombine with electron holes within the device, releasing energy in the form of photons.
-
product
CCD Spectroradiometer
LMS-8000A/LMS-8000
LMS-8000A/LMS-8000 LED Measurement System is an automated measurement system for identifying the performance of individual LED. It is designed to have a capability of producing any visible spectral distribution, mimicking various light sources in the visible region by feedback control of the radiant power emitted by individual LEDs. This LED test system will be used as a transfer standard for photometric, colorimetric and radiometric applications.
-
product
LED Light Source
FOD 114
The LED Light Source FOD 113 or FOD 114 is a light weight and a very small size portable device which has been created to become as popular as a cellular telephone or a pager. The devices of this series are equipped with a universal optical interface which allows quicker hook up to the line, thus saving time for complete measurements. The LED Light Sources meet TIA/EIA-526-14A requirements for coupling power into multimode fiber.
-
product
SLD Light Source
The SLD light source is a light source to emit low-coherence light with a broad spectrum like LED and high brightness like LD. Light emitted from a narrow active layer like LD effectively couple to the fiber. SLD light source can be used for optical measurements and sensors, including fiber optic gyroscopes and OCT. FiberLabs provides fiber-output SLD light sources in different wavelength bands from visible to near-infrared light. Our lineup includes bench-top types convenient for experiments and easy-to-integrate module types.
-
product
SpikeSafe DC / Continuous Pulsed Current Sources
The Vektrex SpikeSafe™ DC / Continuous Pulse (DCP) Current Sources provide reliable DC or pulsed drive for LED or laser diode reliability testing, IESNA LM-80 maintenance testing, and other test applications requiring DC or continuous pulse current. Models support currents from 500mA to 60A and compliance voltages from 50V to 400V. All models feature individual channel control, accurate pulsing over long output cables, precise current, precision pulsing for improved measurement repeatability, and high power density — typically 6.4kW-8kW.
-
product
Mini OTDR Fiber Optic Reflectometer with VFL OPM Laser Source
MT-1300 Plus
Guangzhou Wanglu Communications Co., Ltd.
- Display: 3.5 inch color TFT-LCD screen- Handheld design, light weight and easy operation- Single mode: 1310/1550 nm- Dynamic range: 24 / 22dB (can test about 60 km)- Automatic measurement mode: 1310/1550 nm dual wavelength can be tested simultaneously- Applicable fiber: SM- <8m extra-short event dead zone- Wavelength: 1550nm- Up to 24dB High Dynamic Range- Distance Range: 4,8,16,32,64,128,256km- Pulse width: 3ns-10us- RJ45 cable TDR test & cable sequence test- Optical power meter, Visual fault locator, Laser source- Event Map, can display the length of the link, the type of event point and the position of break point.- USB interfaces, supporting USB stick and printer and direct cable download to PC via ActiveSync- LED light- Built-in friendly-environment lith ium battery with high capacity for over 12 hours of operating life
-
product
LED Solar Simulator
LumiSun-50
The LumiSun-50™ is a high power, multi-wavelength LED solar simulator that meets IEC 60904-9 Class AAA for spectral match, uniformity of irradiance, and temporal stability. The LumiSun-50 achieves a spatially uniform illumination field from a chip-on-board (COB), multiple-wavelength LED die array. The field of illumination is 50 x 50 mm at a working distance of 200 mm. The LumiSun-50 includes a driver/controller which individually provides constant current to each die in the COB array. Total irradiance of 1.1 sun units is provided and can be decreased to 0.1 suns. The LED light source of the LumiSun-50 is contained within an air-cooled housing that can rotate the angular beam alignment. Adjustment and setting of the optimum light path working distance is visually facilitated by a converging pair of red dot laser pointers.
-
product
Power Meter and LED Source
PM23 and LS20DV
The PM23 and LS20DV power meter and LED source are top of the range units for multimode testing of multimode libre links. The PM23 power meter is also calibrated as standard at 1550nm making it suitable for measuring singlemode links when used in conjunction with a suitable source. The LS23DV has 850nm and 1300nm switchable outputs from 1 port and a visible tracer from the other.
