Filter Results By:
Products
Applications
Manufacturers
Optical Amplifiers
Devices that boost light signal in an optical fiber network. The optical signal is amplified directly without need for electrical conversion.
- Pickering Interfaces Inc.
product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-318-M62.5-HI
The 40/42-852A-318-M62.5-HI is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
Logarithmic Transimpedance Amplifiers
Analog Devices translinear logarithmic amplifiers utilize advanced translinear techniques to provide an exceptionally large dynamic range in a versatile and easily used form. Our portfolio relies on proprietary innovations in design and precision laser trimming to achieve the wide measurement range and accuracy in products such as the AD8304 and AD8305. ADI translinear logarithmic amps are used in a variety of applications including optical power measurement, wide range baseband logarithmic compression, the measurement of current and voltage ratios, and optical absorbance measurements.
-
product
Optical Spectrum Analyzer - MATRIQ
1000 Series
The OSA 1000 Series provides grating-based spectral test and measurement. It is an excellent fit for the testing of optical sources, amplifiers, transceivers and passive optical components.The OSA is available in a range of wavelengths for different applications, so you pay only for the capabilities you need.
-
product
Microwave Wideband APD-TIA Receivers
MR12 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR12 series microwave wideband optical receiver, adopts high Sensitivity APD diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
product
CATV Multi-ports Output High Power Full Function Optical Amplifier Module
HHOA-F5000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HHOA-F5000 series is a kind of multi-port output, high power, full-function optical amplifier module and is suitable for CATV with low noise. Its total output power is 27~40dBm (0.5W~10W) optional and its optical output port can reach to 64 pieces at most. The module has standard RS232 interface, adopts high reliable and low power consumption design as well as adopts APC, AGC control mode. The product has two series: The output power of Huatai HHOA-F5000 high power optical amplifier module can be chosen in the range of 27dBm~40dBm. According to different output power, Huatai HHOA-F5000 adopts two latest technical solutions. One is to use single mode high power 980nm pump laser with cooling and EDF, multi-pump synthesis technique. The other is to use multi-mode high power 980nm pump laser without cooling and double-clad Er-Yb doped fiber-optic technology. It provide a whole set of high reliability, low cost, low noise and low power consumption solutions for the application of high power, multi-port output amplifier. It can be widely used in CATV head-end or FTTx distribution network.
-
product
1.0µm PM Fiber Amplifier ( PM YDFA )
HAPM1000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HAPM1000 is a Polarization Maintaining Fiber Amplifier which worked in 1050~1080nm operating wavelength. Adopt Polarization Maintaining (PM) ytterbium-doped fiber, output optical power range 0.5W~5W, extinction ratio >20dB.
-
product
Compact Tunable Laser Source with Continuous Sweep Mode, 1520nm to 1630nm
81940A
Keysight's 81940A high power compact tunable lasers enables optical device characterization at high power levels and measurement of nonlinear effects. It's improves the testing of all types of optical amplifiers and other active components as well as broadband passive optical components. As single slot plug-in modules for Keysight's 8163A/B, 8164A/B and 8166A/B mainframes, they are a flexible and cost effective stimulus for single channel and DWDM test applications. Each module covers a total wavelength range of 110 nm in the C+L-band.
-
product
Compound Semiconductors
GaAs and InP substrates
Sumitomo Electric Industries, Ltd.
GaAs substrates (compound semiconductors) are used for smartphone power amplifiers and switches, LEDs (illumination, decoration, indicators), and solar cells. InP substrates are used for optical communication modules, etc.
-
product
EDFA For CATV, FTTH And HFC Applications
MX-A5400 series
The EDFA is suitable for long haul transmission networks or FTTH distribution networks. This optical amplifier is packaged in a 19” rack mount housing to provide a complete optical communications solution. Maxcom offers our MX-A5400 platform which can be ordered with 8, 16, 32, 64, 128, 256 and 512 output ports and various output powers.
-
product
(70×90×12mm) Single Channel Gain Block MSA Compact Pre-Amplifier EDFA Module
SPA4300-GM02
Hangzhou Huatai Optic Tech. Co., Ltd.
SPA4300-GM02 is a gain block optical Pre-amplifier EDFA module, adopts 70×90×12mm MSA compact package. It is featured with high reliability, superior optical performance and compact reasonable configuration by Industrial standard, creating the most flexible and variable low-cost amplifier in the market. This module is suitable for multiple network application, especially the application that requires 40GB/S transmission speed.
-
product
Photoluminescence & Electroluminescence Measurement System (PL/EL)
PL
PL/EL Measurement System includes Laser, Spectrometer, Lock-in amplifier, Optical Chopper, Sample Holder(PL/EL), PMT/CCD, Fiber, Optical optics, Optical Table, Refrigerator（low temperature）,Sample Chamber and related accessories;
-
product
Femtosecond Pump - Probe Transient Absorption System
Hatteras
The Hatteras is first professional system on the market for ultra fast transient absorption pump - probe spectroscopy. Two linear image sensors (multichannel detection) or two photodiodes (singlechannel detection) are placed behind an imaging spectrometer to measure probe and reference pulses, originating from a femtosecond white light (continuum) generator or from an optical parametric amplifier.
-
product
Fiber Pigtailed Tapered Amplifier
The AOSense tapered amplifier (TA) provides a coherent high-power beam, inheriting all properties from the seed source. TA’s are an essential optical component for quantum sciences, such as laser cooling and trapping, cold atom sensors, electromagnetically induced transparency, and quantum spectroscopy. The TA is also used in commercial laser modules, including master oscillator power amplifier (MOPA) lasers and external cavity lasers.
-
product
High-Power Multi-Ports Output CATV EDFA (1540~1563nm)
HA5400B (2RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5400B (2RU) series is a high power multi-ports optical amplifier with gain spectrum band within 1540~1563nm. It is mainly designed for the application of CATV or 1~8 continuous banding channel (ITU wavelength). It offers a flexible and low-cost solution for CATV large area coverage of metropolises and medium-sized cities.
-
product
Detection Electronics
Our detection electronics portfolio comprises all the detection electronics elements required for the operation and automation of a high quality light measurement system, including photo-detector signal recovery and digitisation (with fully programmable DC, AC and lock-in amplifiers having current/ voltage inputs), high voltage supply, optical chopper control, detector thermoelectric cooler control and relay unit.
-
product
SPICE software for Opto-Electronics
OptiSPICE is the first circuit design software for analysis of integrated circuits including interactions of optical and electronic components. It allows for the design and simulation of opto-electronic circuits at the transistor level, from laser drivers to transimpedance amplifiers, optical interconnects and electronic equalizers.
-
product
Optical Limiting Amplifiers
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
product
Amplifiers
Alnair Laboratories Corporation
A specially designed Erbium-doped fiber amplifier which offers a superior optical amplication performance with a very high gain factor and a minimal added noise. A near quantum limited noise figure of typically 3.8dB, and a small-signal optical gain of over 50dB is achievable with input signal as low as -50 dBm reflecting the impact of the specialty fiber and composite amplifier design, making it an indispensable amplifier for weak optical signals.
-
product
Light
Welcome to Thorlabs; below you will find links to light emitters, sources, and controllers, a subset of our entire line of photonics products. Our light sources are conveniently separated into coherent and incoherent sources. The coherent source category includes laser diodes, laser diode modules, tunable lasers, HeNe lasers, and femtosecond lasers, while the incoherent source link brings you to a selection of LEDs, white light, and broadband SLD sources. The Quantum Electronics category includes optical amplifiers, modulators, and gain elements that are frequently used in research and OEM applications. All of our light sources and optical amplifiers are supported by an extensive line of mounts, sockets, TEC controllers, and current controllers.
-
product
Light-to-Analog Sensors (Voltage)
Renesas' light-to-voltage silicon optical sensors combine a photodiode array, a non-linear current amplifier and a micropower op amp on a single monolithic IC. Applications for these devices include display backlight control, keypad dimming, anti-glare mirror systems, and industrial and medical light sensing applications.
-
product
O Band Tunable Laser Source
CA9812
The CA9812 O Band tunable laser integrates a widely tunable laser with a semiconductor optical amplifier (SOA). The tunable laser is electronically tuned and can address any wavelength from 1265.00 nm to 1365.00nm. The integrated SOA facilitates flexible control of the output power and acts as a shutter when reverse biased, enabling dark tuning between channels. The device is packaged into a standard module box package, with an ternal optical isolator and a polarization maintaining fiber output.
-
product
FTTx PON Optical Amplifier (1540~1563nm)
HA5800E (5RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5800E (5RU) series is a low noise, high performance, FTTP high power, multi-ports optical amplifier with gain spectrum band within 1540~1563nm. Each output port for optical amplifier has built-in well-performed CWDM. Every external up-link optical port of optical amplifier can connect with OLT PON port very conveniently. Each 1550nm (CATV)'s output optical port multiplex 1310/1490n's data stream, in order to reduce the quantity of the component and improve the index and reliability of the system.
-
product
Optical Transimpedance Amplifiers
Analog Devices optical transimpedance amplifiers offer a complete, high performance, single chip solution for converting photodiode current into a differential voltage input. Supporting data rates from 155 Mbps to 11.1 Gbps, our transimpedance amplifiers are ideally suited for data communications and telecommunications applications supporting lay protocols including 1×, 2×, 4×, and 8× Fibre Channel, 10GBASE-LX4, SONET/SDH up to OC-192 with FEC, and 10 Gigabit Ethernet. Our transimpedance amplifiers feature low input referred noise current, high input current, and low power dissipation.
-
product
Optical Communications and Sensing
The Analog Devices optical portfolio covers a range of technologies, such as current mirrors, translinear logarithmic amplifiers, laser diode driver ICs, and optical sensors, to provide designers the tools they need for their optical applications. Our optical portfolio supports GbE optical receivers, Fibre Channel, WDM transponders, telecommunications, and next-generation optical networks.
-
product
(70×90×15mm) C-Band DWDM FGA Full Function Module Fixed Gain EDFA Module
FGA4400-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai FGA4400-FM02 series is a fixed gain Full Functional EDFA module which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
product
High-Power Multi-Ports Output CATV EDFA (1540~1563nm)
HA5400C (3RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5400C (3RU) series is a high power multi-ports optical amplifier with gain spectrum band within 1540~1563nm. It is mainly designed for the application of CATV or 1~8 continuous banding channel (ITU wavelength). It offers a flexible and low-cost solution for CATV large area coverage of metropolises and medium-sized cities.
-
product
External Cavity Diode Lasers
ECDLs
High-performance ECDLs and injection-locked optical amplifier.
-
product
Power Probes
RkP-500 Series
The RkP-500 Series probes take advantage of synchronous detection (chopper/lock-in amplifier) technology to offer unparalleled background noise rejection, S/N ratio, and sensitivity. Total power, average power, and irradiance can be measured. The probes can be mounted directly onto the Rk-570C Optical Chopper to form an integrated measurement system, or the chopper can be operated remotely from the probe.
-
product
Gated Integrator | Boxcar Averager
GIA100
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
product
Ray tracing and Laser Simulation / Cavity Design Software
LasEasy V1.0
LasEasy software is the professional software for simulating and designing solid-state laser cavity, optical amplifier system, and parametric OPO systems. It can also simulate the laser light propagation in both horizontal and vertical (sangital and tangitial) planes.
-
product
EDFA Optic Amplifiers
Wuhan Sunma Technology Co., Ltd.
With the feature of high input power, high output power, and medium optical gain, the booster amplifier operates at the transmission side of the link to amplify aggregated optical input power for reach extension.SunmaFiber booster amplifier is a low-noise, gain-flattened C-band optical erbium doped fiber amplifier (EDFA) designed to cost-effectively extend the optical link power budget for building long distance DWDM solutions.SunmaFiber also offers switches, routers and fiber converters including 10/100M, 10/100/1000M and 10G fiber converters, SFP fiber converters, manageable/unmanageable fiber converters, OEO fiber converters, POE fiber converters, fiber converter cards, and fiber converter chassis; transmitting distance from 2km(MM) to 150km(SM) with SC or LC or FC connectors.
