Filter Results By:
Products
Applications
Manufacturers
Power Calibration
Verify power measuring instruments accuracy.
See Also: Calibration, Calibrators, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
- Pickering Interfaces Inc.
product
PXI Power Relay Module, 16xSPST, 16 A
40-161A-001
The 40/42-161A-001 is a PXI/PXIe 16xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
product
Average Power Sensors
E9300
Operates with the EPM, EPM-P and P-series power meters Wide dynamic range sensors (80 dB maximum)Accurate average power measurements on all modulation formats Wide frequency coverage from 9 kHz to 18 GHz (special option to 24 GHz)Calibration factors stored in EEPROM Fast measurement speed over the GPIB (up to 400 readings per second with the E4416A)
-
product
Power and Energy Automated Calibration System
RS-933
The RS-933 Syntron Power and Energy Automated Calibration System calibrates a range of test equipment including; Energy Reference Standards, Digital Multimeters, Phase meters, Energy meters, Power meters, Revenue meters, Amp meters, Panel meters & Power Quality meters.
-
product
Deskew Calibration Source for CP030, CP030A, CP031, CP031A, AP015, CP150, CP500
DCS025
The DCS025 Deskew Calibration Source generates time-aligned voltage and current pulses for precise deskew of voltage and current probes.This is critical for measurements in which small propagation delay differences between probes can have a large impact on a calculated measurement, e.g., instantaneous power semiconductor device loss measurements.
-
product
Optical Power Meter & VFL & RJ45 Network Test
TM263N
◇ Added Network Cable Test ◇ Accurately test whether a single network cable transmits signals normally ◇ Self Calibration ◇ Set the Auto Off ◇ Wavelength Memory function after turn off the tester ◇ High Accuracy, high ,High sensitivity, high linearity ◇ Stable VFL Output ◇ USB Charge port ◇ FC,SC Connector ◇ 18650Li-ion Battery ◇ Lower power consumption design, long standby time ◇ Rubber Out shell, increased the protective properties for field work
-
product
Three Phase Power Meter
929A
Model 929A Three Phase Power Meter is an economical alternative to both the Model 931A Power System Analyzer and the Model 930A Three Phase Power Analyzer when serial communication, dc voltage measurement, transducer calibration and timer features are not required. The Model 929A has the same ac accuracy as the Model 931A with PowerDSA™ Digital Signal Analysis, and is a complete diagnostic tool for use in the substation and industrial power environment.
-
product
TorqueLab® Torque Analyzer
LTT-Series
The torque analyzer is designed for calibrating tools, joint testing, auditing and measuring torque. Torque tools go out of calibration with use. To maintain consistent accuracy, torque tools must be checked periodically for wear or defective parts. A power or hand torque tool is a measuring tool that must be properly calibrated and maintained. The LTT-Series is an advanced torque testing and documentation solution. Using a quality torque tester makes a safer world through accuracy and precision. Controlling torque is essential for companies to ensure their product’s quality, safety and reliability isn’t compromised.
-
product
Air Quality Analysis
Ambient Gas Monitoring: We offer a variety of analyzers for the ambient monitoring of the criteria pollutant gases, including CO, NOX, SO2, and others such as CH4 and CO2. Source Gas Monitoring (Emissions Monitoring): Experience reliable measurement in your process for emissions compliance every time.Ambient Particulate Monitoring: Experience our monitoring technology and gain the power to do more than just inform.Emissions Calibrators: For continuous monitoring of mercury in exhaust stacks, waste incinerators, and cement kilns, or multi-gas models to control the calibration of gas concentrations.
-
product
Digital Power Meter
2406B
‧Simultaneous display of W, A, V (PF or Hz)‧True RMS V, A, W‧Auto calibration via computer‧Data Hold∕Range Hold function‧Hight immunity to external noise‧CT ratio (1～99)‧REF function (0.800 ～ 1.200)‧Aux. power is AC 90 ～ 260V, 50/60Hz‧RS-232 interface (option)
-
product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
product
Power Measurement
Precision Acoustics manufactures Radiation Force Balances and Check Sources which can be used to measure ultrasound power according to the IEC Standard 61161. All products are supplied with a calibration from The National Physical Laboratory, LONDON.
-
product
EcoTestr™ pH1 Waterproof Pocket Tester
The economical, simple-to-use pH tester measures pH levels and temperatures quickly, displaying them both simultaneously on a large dual-line LCD. It has a pH range from 0 to 14 with an accuracy of ±0.1 pH. The tester features up to three pH calibration points with auto NIST and US buffer recognition. Additional features include a long-lasting durable electrode with polymer reference electrolyte; status icons for measurement stability, calibration, and battery life; and self-diagnostics. The IP67-rated housing features an easy-to-grip design and floats if accidentally dropped in water when sensor cap is on. The tester, powered by four AAA batteries, can operate up to 400 hours continuously. The unit will auto power-off after 8 minutes of nonuse to conserve power.
-
product
10 MHz To 54 GHz USB Wide Dynamic Range Peak And Average Power Sensor
U2066XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Spectroscopic Reflectometer
SR Series
Angstrom Sun Technologies, Inc.
Spectroscopic reflectometer (SR) tools are relative low cost and easy to use. To ensure accurate measurement on spectra, a long working distance and also adjustable working distance set up are professionally designed and considered. Since reflection spectra measurements require to use known reference to calibrate light intensity, it is hard to image that user could get accurate spectra without optimizing signal during such calibration because reference thickness is different from sample substrate's thickness in most of cases. Adjusting power output to lamp is our another consideration in ensuring a good measurement by reducing non-linearity effect of the detector.
-
product
10 MHz To 54 GHz LAN Wide Dynamic Range Average Power Sensor
L2056XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
10 MHz To 67 GHz USB Wide Dynamic Range Average Power Sensor
U2057XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
product
Three Phase Electrical Power Calibrator
6003A
The Fluke Calibration 6003A Three Phase Electrical Power Calibrator is the most cost-effective way to get the superior accuracy and performance of three independent phases in one instrument. It is an ideal solution for calibration laboratories, electronics manufacturers, electric utility meter shops, and other organizations that manufacture and maintain energy meters, power quality analyzers, and similar tools.
-
product
USB Controlled Loudspeaker & Microphone Test Interface
AmpConnect™ ISC
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
DC/10 MHz 50 GHz USB Thermocouple Power Sensor
U8487A
The U8480 series is Keysight's first power sensor with the capability to measure down to DC (only applicable for U8481A/85A). Now, with an expanded frequency range up to 50 and 67 GHz, the U8480 series allows you to make fast and accurate high frequency power measurements in applications ranging from PNA/MXG calibration to high volume manufacturing.
-
product
Electrical Calibrators
An electrical calibrator, or dc calibrator from Fluke Calibration includes many innovative and multi-functional solutions to help laboratories operate efficiently, increase throughput, and comply with today’s quality standards. Versatile models and options provide a wide range of possibilities to match a variety of workloads and budgets. Electrical calibrators include: Multi-product calibrators; multifunction calibrators; oscilloscope calibrators; power calibrators; pressure/temperature calibrators.
-
product
Chamber Simulator System
BroadSim Anechoic
Built on our proven BroadSim platform, BroadSim Anechoic allows users to accurately simulate real-world GNSS environments in their Anechoic Chambers. BroadSim Anechoic has 32 individual RF outputs enabling the system to drive 16 dual-frequency antennas. Revolutionary features like automatic antenna mapping, automatic time delay calibration, and automatic power loss calibration are what make BroadSim Anechoic the most advanced Anechoic Chamber simulator on the market today.
-
product
pH 620 Waterproof Meters
These waterproof handheld meters feature a –2.00 to 20.00 pH range with 0.001 pH resolution. Combined with accuracies up to ±0.002 pH, these meters provide a new benchmark in our pH meter line. Store up to 500 data sets in the meter‘s memory. Time-and-date stamping meets Good Laboratory Practice (GLP) standards.The pH 620 meters offer the latest in pH calibration capabilities including up to six calibration points, a user-settable “calibration due” alarm, and up to 15 buffer options with auto-buffer recognition of USA, NIST, DIN, and PWB standards. The infrared (IrDA) wireless technology makes PC downloading more convenient and easier. Dual powerup allows you to use batteries while out in the field or the optional AC power adapter while in the lab.As always, our waterproof meters are IP67 rated for protection against both dust and water, even with no probes attached.
-
product
Emissions Dynamometers
MD-250-M
Mustang has developed a low-cost, simple to use, easy-to-install heavy duty chassis dynamometer that can be used to simulate real-world driving conditions in a safe, controlled environment and can also be used for “static” diesel smog testing for regulatory purposes. This model is used in Diesel Smog Programs in Nevada and Colorado when combined with an approved opacity meter. The MD-250-M is a compact dynamometer with industry proven design features including 10.7-inch rollers, heavy duty spherical pillow-block ball bearings, welded structural steel frame, 7.5 hp calibration motor, and an industry standard air-cooled, Eddy Current Power Absorption Unit (PAU) for road-load simulation. The MD-250-M is available in both right and left hand configurations to accommodate different facility designs.
-
product
High Speed Data Logger
9330
The Model 9330 displays 24-bit resolution and has an impressive 3750Hz update rate. Incorporating peak and valley capture, it can store up to 6 sensor calibrations and measurements from load cells or torque transducers can be logged at 1000Hz to a standard SD card. This data can then be downloaded to a PC via the built-in USB port and Windows compatible software for off-site analysis. Adding further versatility, the rechargeable battery can power up to 4 x 350 ohm sensors, but also offers up to 300 hours stand by time and up to 20 hours continue use.
-
product
Gain-Compression Measurements
S95086B
The S95086B Gain-Compression Measurement (GCA) software provides fast and accurate input power, output power, gain, and phase at the compression point of an amplifier or frequency converter over a specified frequency and power range. With a simple setup, GCA reduces test times through an easy-to-use, fast, and accurate SMART Sweep. GCA also includes a guided calibration that corrects for absolute power levels, frequency response, and mismatch errors.
-
product
RF Calibration Kit
SMK-3000
The SMK calibration kits are precision, high power calibration standards that are used to calibrate RF radios, wattmeters, directional couplers and other high-power RF test equipment in the field or metrology lab. Unlike other calibration solutions, the SMK-3000 calibration kits reduce the cost of ownership and provide a much faster time-to-calibration with lab precision and accuracy you’ve come to expect from Bird.
-
product
Open-Short-Load RF calibration kits
Open-Short-Load RF calibration kits from Fairview Microwave are available with Type N or 7/16 DIN connectors. Type N open-short-load RF calibration kits have male or female genders, 7/16 DIN open-short-load kits are male gender. Type N open-short-load (OSL) calibration kits for RF have a minimum frequency of 0 (DC) and a maximum frequency range between 4 GHz and 6 GHz. Type N open short load kits for calibration have a maximum power handling of between 1 Watt and 2 Watts.
-
product
PC/104 8-Channel Smart Sensor Interface
518
Measures thermocouples, RTDs, strain gages, thermistors, 4-20 mA, voltage and resistance 8 high-accuracy differential input channels Integral sensor excitation Exclusive pulsed excitation minimizes sensor self-heating Configurable sensor type per channel Fully electronic calibration Low power
-
product
Slow Speed Switch
SS110
Features • Works with remote/external pulse frequency output sensor (NPN, PNP) • Setpoint ranges: 0.01-0.99 & 0.1-9.9 rpm • SPDT relay output • Monitors speeds down to 100 min. per rev • Dial-in calibration does not require power • Built-in start delay • DIN rail mounting simplifies installation • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options
