Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI 8-slot BRIC Power Multiplexer, 24-Channel, 6-Pole (5 Sub-cards)
40-571A-403
The 40-571A-403 is a 24-channel, 6-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
Power Factor RLC Load
3282（280V,1875W / 3700VA ）
3282 power Factor RLC Load built-in 16-bit A/D and DSP precision measurement circuit, provides accurate measurements, measurement items have Vrms, Arms, Watt, VA, CF, PF, THD, VTHD, ITHD, Ipeak, Amax, Amin, Vmax, and Vmin. In addition to these measurement functions, it also provides time measurement，products such as UPS, fuses and circuit breakers etc. trip or blow time and transfer time for Off-line UPS
-
product
RF Milliwatt Meters
Type NDB-2 and NDB-3
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
product
Power Supply
Shijiazhuang Suin Instruments Co., Ltd.
A power supply is an electrical device that supplies electric power to an electrical load.
-
product
Eddy Current Chassis Dynamometers
Cradle- or single-roll (top-mount) dynamometers accommodating single- or tandem-axle vehicles, with continuous vehicle power ranges from 50 hp to 622 hp (37 kW to 464 kW), Taylor’s chassis dynamometers allow a top recommended speed of 90 mph (145 kph) at full load. Look to our experts to not only help you select your optimal system, but also to provide design, configuration, installation and training for a total solution that integrates seamlessly with your operation.
-
product
Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A
72-8690A
The 72-8690A from Tenma is a dual channel general DC power supply suitable for laboratory use. The dual channel (CH1 and CH2) can work in CV or CC mode and these two modes convert automatically according to the load. The CH1 and CH2 have auto tracking function. In this condition, the output of CH2 tracks the output of CH1. This function is usually used when adjustable symmetrical and double polarity power is required. Both CH1 and CH2 display the output voltage or current with a 6 digit LED meter. The main outputs can be connected in parallel or in series. This product comes with 2 years warranty.
-
product
Multifunction Meter
Easy navigationEvent recording with time stamp (all basic & power parameters)Unbalance load and voltage with calculated neutral currentDynamic communicationOptional digital output for all basic and power parameters
-
product
L.V. Power Capacitors
LV power capacitors are circuit elements which compensate the inductive reactive loads on a system. Being able to connect and disconnect up to 100 times a day in accordance with load variations in automatic reactive power compensation systems really speaks for the quality and endurance and capacitors. Upon connection/disconnection instances, currents which have higher values than the nominal value may occur on reactive power compensation capacitors. ENTES ENT.C series power capacitors are designed to withstand the severe and poor conditions which may shorten the operating life during reactive power compensation. This endurance is the result of advanced engineering and long-term test procedures.
-
product
PXI 20Amp 28Volt 4xSPST Automotive Relay
40-180-111
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
product
Desktop Test Interface Station
2210
TESCO’s new Desktop Test Interface Station (Catalog No. 2210) provides metering professionals with exceptional testing flexibility. The Test Interface Station is ergonomically designed for meter technicians working in a lab or a desktop, yet still rugged for field use. The Test Interface Station includes a zero insertion force (ZIF) meter socket, voltage selection, form selection, open/closed-link selection and bi-directional cabling to power a load box/test kit & connect test standard potentials. When combined with a test kit/test standard and powered via 120 VAC, the Test Interface Station creates a single position, stand-alone, meter accuracy testing device for various socket based meters (both mechanical & solid-state).
-
product
4500~6000W DC Electronic Loads
JT634 Series
Nanjing Jartul Electronic Co., Ltd
JT634 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT634 series load very suitable for testing power supply when produced in large quantity. Besides, JT634 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT634 series load satisfing most of R&D requirements. Moreover, JT634 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
product
Energy Saving Static Converter
The ENERGY SAVING static converter serves to generate a controlled squarewave single-phase alternate voltage (low frequency: 25 ÷ 125Hz) for industrial applications requiring high load power supplied by an external matching transformer. The power supply, sectioned by remote control switch and external fuses, is fed by a three-phase electric line via uncontrolled diode bridge and filtered by inductor and capacitor battery. The DC voltage thus obtained is converted into single-phase alternating voltage via “H”-shape bridge of semiconductors in order to control impressed frequency single-phase transformers.
-
product
Transformer Testing And Monitoring
Can detect the symptoms of transformer failure by monitoring the cooling system, load tap changer, dissolved gas, bushing power factor and capacitance, partial discharge, oil levels, pressure, temperatures and more.
-
product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD | VP 230036
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
product
BNC To BNC Cable, 50 Ohm, 0.9 M
781887-01
Connects measurement and signal generation devices. Model options include industry-standard coaxial connector types including BNC, SMA, SMB, and MCX. Long cables can act as antennae picking up extra noise that can affect measurements, so ensure you select only the length required for your test system. Also look at the impedance of your test system and consider buying a cable with the same impedance. Matched impedance can maximize the power transfer or minimize signal reflection from the load of your system.
-
product
Bench Power Supply, Calibrated, Adjustable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2690 CAL
The 72-2690 CAL from Tenma is a single channel adjustable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has complete digital control, intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
product
Voltage Sag Generator
SKS-1120GTB
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
product
Bidirectional Programmable DC Power Supply(5kw ~ ±180kW)
FTB9000 Series
Shenzhen FaithTech Technology Co., Ltd.
FTB9000 series is a regenerative bidirectional programmable DC power supply, it is not only a stand-alone bidirectional DC power supply but also can be used as a regenerative electronic load, to absorb the consumed energy and feedback cleanly to the grid. The high-efficiency energy feedback efficiency not only saves electricity consumption and heat dissipation costs but also does not interfere with the operation of the power grid. It is widely used in high-power testing scenarios such as automotive electronics, new energy vehicles, photovoltaic energy storage, intelligent industrial equipment, battery simulation, etc.
-
product
Power Supplies
V-600
The V-600 is feature a 140mm ultra silent cooling fan and single PCI-E connector to power your high-end graphics card and keep your system cooler. The triple rail 12V outputs design allow for optimum load balancing in better performance and stability.
-
product
Development
Our JTAG Switch Modules (JSMs) are flexible testing and diagnostic cards to accelerate the design, prototyping and operation of your embedded computing system. We have a range of AMC modules for IPMI software development, power load testing and monitoring or to provide a telco/fabric clock. Also, our single slot backplane for AMC modules is ideal for low-cost development and testing.
-
product
48V / 250 Amp Load
BD15-48P
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
product
Power Supplies
ZPG-600B
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
Dual High Speed Power Supply
VX4620
Dual high speed power supplyLow noise linear output stage with 200 Vpp and 1 AProgrammable bipolar voltage and positive/negative current limitsStable control loop even on long load linesAuto sensing featureProgrammable slew rateProgrammable over GPIB, USB or RS232Fast rise and fall times due to integrated sink capability
-
product
High Voltage Power Source
PM1000
The PM1000 is a high voltage power source capable of supplying up to 1000 V/20 mA to a load. It is intended for use in measuring leakage and breakdown voltages of devices. There are five voltage ranges and five current ranges.
-
product
1-phase Power Analyzers
PeakTech Prüf- und Messtechnik GmbH
Is a high-precision energy cost measuring device for recording the energy consumption of electrical devices and for calculating the current consumption of a device by entering the electricity price. Thanks to the integrated power factor calculation, all modern consumers such as Switching power supplies, TV sets, fluorescent lamps, LED systems and of course ohmic loads such as Electric heaters and hobs can be measured accurately. In addition, the high resolution, the low response characteristic and even very small or stand-by consumers from approx. 1 W can be measured.
-
product
3CT Method Clamp Tester
MCL-4000F
MULTI MEASURING INSTRUMENTS Co., Ltd.
*3CT method enabled easy AC leakage current measurements with simple clamping of each phase conductor by 3 CTs or 4 CTs.*Use 4 CTs for 3phase/4wire power system.*Load current measurements for each phase conductor up to AC 800A.*Filter rejection for high frequency noise.*DC mV output for recorder.
-
product
Power Supplies
ZPG-500B
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
PXI 10 Channel Power Mux 1 Pole
40-660-001
Model 40-660 is a 10-Channel Power Multiplexer, suitable for switching inductive/capacitive loads up to 10A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions). Model 40-665 is a higher density 18 Channel Power Multiplexer with the same specification as the 40-660. Power Multiplexer Modules are intended for switching heavy AC or DC loads or for slave switching large external relays, contactors and solenoids.
-
product
Mission Critical, Fault Tolerant Power Supplies
Series HSF
- Hot-swappable plug-in power supplies.- Designed to be combined in an N+1 fault-tolerant power system.- Front panel voltage adjustment trimmer for adjustment of output voltage.- Built-in forced current sharing and or-ing diodes.- May also be used independently as a multi-output power supply.- Designed to be sustainable - new models are backward compatible with existing racks.- Available in 1U and 3U sizes. Mounts in 19-, 23-, and 24-inch equipment racks.- All models include power factor correction (PFC).- Full service customized DC power distribution systems can match power supply output(s) with your load(s).- I/O connections via 24 pin connector that plugs into rack adapter. External connections are made via rack adapter.- Surface mount technology permits minimum mounting space.- Entire RA 19 racks populated with HSF power supplies can be connected in parallel, parallel-redundant or series.- HSF are CE Marked per per the LVD, EMC and RoHS 2 Directives. See applicable Declaration of Conformity.- Compliant with UL 8750, Standard for LED Equipment,- Watch video of NEBS GR-63-CORE earthquake and office vibration testing.
-
product
Triple Output DC Power Supply, 30V/6A (2x) & 5V/3A; 375W
U8031A
Keysight now extends its range of basic DC power supplies to offer 375watt power range, making it an ideal power source alternative in electronics manufacturing, research and development as well as the education sector. The U8031A, basic DC power supply, is a manual triple-output power supply with sequencing capability. With this function, users can generate output sequences with minimal programming skills. Each power supply is also built with excellent load regulation and clean output noise for continued stability. With these and many other features, you get a solid and reliable triple-output power supply at an unsurpassed performance.
-
product
PXI Power Multiplexer, 10-Channel, 2-Pole
40-660A-002
Model 40-660A-002 is a 10-Channel 2-Pole Power Multiplexer, suitable for switching inductive/capacitive loads up to 8A at 250VAC. It is available with a choice of 1-pole (10A) or 2-pole (8A versions).
