Filter Results By:
Products
Applications
Manufacturers
SCR
Thyristor, Silicon Controlled Rectifier
- Scientific Test, Inc.
product
Automated Discrete Semiconductor Tester (ATE)
5000E
Same Proven Technology as all 5000 Series Testers. High Speed Single Test Measure. Capable of Testing Multiple and Mixed Devices. 1KV Standard, 2KV Optional. 1NA to 50A Standard, 100A Optional. 0.1NA Resolution. Complete Self Test. Auto-Calibration. RDSON to 0.1MOHM Resolution. Windows Application Software. Optional Scanner. Optional Wafer Mapping. Optional Curve Trace. MOSFET, IGBT, J-FETTriac, SCR, Sidac, Diac, Quadrac, STS, SBS Transistor, Diode, Opto, Zener Regulator, MOV, Relay. UNDER $23,000.00
-
product
Test Setup For Domestic Mixer Motor
SCR ELEKTRONIKS have developed TESTING SET UP FOR MIXER MOTOR for carrying out performance test and High Voltage test of mixer at final stage. It consists of Voltmeter, Ammeter and Watt meter for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of HV test. HV test is provided with tripping cut off concept. Output Socket is provided for quick connections and disconnections of the equipment to be tested. User friendly operations make the equipment to be handled easier for any operator.
-
product
Stored Energy Solenoid Drivers
B-1014
The remote contact controlled HCA Series and the SCR controlled HCB Series of Stored Energy Solenoid Drivers produced by Ross Engineering Corporation are used for high speed opening or closing of Ross Circuit Breakers and Contactors. They perform high speed microseconds to milliseconds actuation of various electromechanical devices. The units feature minimum internal time delay, trigger signal overload protection, and up to 3000 joules of energy storage.
-
product
MCB Temperature Rise and Power Loss Test Bench
The SCR Elektroniks 3 station MCB Temperature Rise and Power Loss Test Bench is economically designed to verify temperature rise and measure power loss as per clause 9.8 of IEC 60898 with the circuit designed to follow test procedure as per Cl 9.8.2. The temperature rise is measured in accordance with Cl 9.8.3 and 9.8.4 while power loss is measured and verified as per Table 15 of Cl 9.8.5.
-
product
AdBlue & Urea Refractometer
RHA-503ABATC
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
The AdBlue refractometer RHA-503ABATC is a new hand held refractometer developed to address the growing need to check the urea concentration in AdBlue.Escalating urea prices have driven the cost of operating an SCR higher than ever before. Regretfully this has led to a new wave of problems where supplies of diluted AdBlue have found their way in to the market.Often rebranded ‘Automotive urea solution’ to eliminate the risk of prosecution by trading standards (as a mix of less than 31.8% urea cannot be labelled AdBlue). Victims of this weaker concentration may not be able to seek compensation under the Trades Description Act.
-
product
PC Based Comprehensive Test Setup for Luminaires
Our zest for innovation has resulted in continuous upgrades in the existing line of products. Till now we used to manufacture 3 different equipments for Driver, MCPCB and Luminaires Component testing. We at SCR Elektroniks have developed our comprehensive tester to incorporate all the 3 systems in a single bench. Here in this tester one can test all the three DUT in a single bench. Since all the 3 testing procedures have many tests in common, we have incorporated all the tests in a single bench such that testing of Luminaire driver, Luminaire PCB and Final Luminaire set is performed in single test bench. Only these tests are performed over the DUT else other are disabled for them.
-
product
Bench Digital Multimeter, 3.8, USB, 20 A, 1 kV, 60 Mohm
72-13620
*True RMS bench top digital multimeter with 6000 counts display*CAT II 600V safety rating*Manual function select and auto ranging*Transistor & SCR measurement*Data hold, max/min modes*EBTN (Enhanced Black Twisted Nematic) LCD backlight*USB interface*Input protection*Powered by 100V/120V/220V/240V ±10%, 47Hz to 63Hz supply*12-month limited warranty *view Terms & Conditions for details
-
product
Surge Suppressor to Suppress SCR Spikes from Customer Equipment Going Back to Utility Power, P/N 5965C
This Suppressor Board is ideal for SCR Controlled Power Supplies when SCR control is on the primary side.The Suppressor Board will prevent SCR spikes to go back into the 480 VAC utility power lines.
-
product
Tumbling Barrel Test Apparatus
SCR Elektroniks make Tumbling Barrel Apparatus is specially designed and manufactured for use in laboratories involved in testing Appliances, Electrical Accessories, Luminaries and other related Electro technical products. It is used to perform the test specified in many standards to determine compliance with safety requirements, particularly mechanical strength of test samples. SCR Elektroniks Makes Counter to count ON/OFF of Limit switch.
-
product
Safety Test Panel for Mixer
SCR ELEKTRONIKS introduces Safety Test Panel for Domestic Mixer with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 20 seconds. Micro controller based sequential timer maintains the sequence of operation and displays the test status. This manual contains information about operating instructions and maintenance of the equipment. Please go through this manual carefully and retain it for future reference.
-
product
DC Power Supplies
SGe Series
AMETEK Programmable Power, Inc.
The SGe is an economical, FET based, high switching speed, programmable, dc power supply alternative to SCR and IGBT based dc supplies.
-
product
Cord Swiveling Test Set Up For Hair Dryer & Hair Straightner
SCR Elektroniks make CORD SWIVELING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis,20 Revolutions clockwise & 20 Revolutions anti-clockwise.
-
product
MOTORIZED TRANSFORMER/RECTIFIER ASSEMBLY, 0-250 VDC, 200 A OUTPUT
18534PS1
Input power is 380 VAC, 3 PH, 50 Hz, P/N 18534PS1Output is 0 to 250 VDC, 200 Amp max.Variable Transformer is used to vary the output. SCR controller is not used, as it generates harmonics.Input control is 0 to 3.6 VDCIndoor enclosure, 50"H x 46"W x 36"DOutput voltage and current feedback as 4/20 mA for PLC interface.All input/output connections are inside the enclosure
-
product
Cord Flexing Test Set Up For Hair Dryer and Hair Straightner
SCR Elektroniks make CORD FLEXING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis, Clockwise & Anti-clockwise. Frequency is 10 turns in one minute.
-
product
Relays for High Power Applications
Series ST
Series ST relays are designed for high-power applications. The design incorporates an SCR or triac output. The relays utilize optical isolation to protect the control from load transients. A control LED is available on certain models. Internal MOV is also available on ST24D 25A and 50A models. All Series ST relays are Zero-Cross switching.Available options include:ST24D12 12A, 12-280Vrms, 600Vpeak Load; 4-30Vdc ControlST24D25 25A, 12-280Vrms, 600Vpeak Load; 4-30Vdc ControlST48D50 50A, 24-600Vrms, 1200Vpeak Load; 5-30Vdc Control
-
product
4 Station Endurance Test Setup for Thermostat of Iron
SCR ELEKTRONIKS have developed 4 STATIONS ENDURANCE TEST SETUP FOR THERMOSTAT OF IRONwhich is used for carrying out endurance test for thermostat of iron for the required amount of time It is very useful and handy in line testing on Mass production line as well as type Testing. It consists of Voltmeter, Wattmeter, Programmable Logic Controller( PLC ). The equipment continuously monitors faults like Contact weld and Contact Open. The other important feature is we can operate the panel in Auto Mode or Manual mode. User friendly operations make the equipment to be handled easier for any operator. This manual contains information about operating instructions and maintenance of the equipment.
-
product
SCR Controller with Regulator
The SCR Controller and the Regulator Board are used in SCR controlled power supplies.CEHCO offers single phase and three phase SCR Controllers with Regulator Boards.
-
product
Safety Test Panel for Water Cooler
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of washing machines. In addition to the conventional safety tests, test for performance is also included.
-
product
Commutator Testing Unit
SCR ELEKTRONIKS have designed “Commutator Testing Setup” to provide Commutator manufacturers and users a simple and speedy method for testing their Commutators. This single station commutator testing set up therefore user can test one commutator at a time. In Automatic mode of testing this set up performs two tests automatically.
-
product
Test Finger Apparatus
SCR ELEKTRONIKS focuses on designing a solution around the end use at her customer. Instead of offering a standard instrument for a specific task, we have an approach of customizing the test bench to target the specific goals of the process or test procedure. Our measurement instruments, test modules, electrical power systems & software libraries are developed with this vision, thereby reducing the test system’s time-to-deploy.
-
product
DC Constant Current Source
SCR ELEKTRONIKS have developed equipment namely“DC CONSTANT CURRENT SOURCE”. The system comprises of Constant Current Sources having ranges: 900A continues & 3000A short time at 8V maximum.
-
product
SCR, Diodes & Assemblies
SCR and Diodes are available as assemblies or discrete parts. Most assemblies are encapsulated. CEHCO stocks a variety of rectification products such as Diodes, SCR’s (silicon-controlled rectifiers), and Encapsulated Assemblies. We SCR and diodes replacement specialist. We specialize in obsolete and hard-to-find SCR and diode assemblies. We can offer an equivalent replacement for most obsolete rectification devices.
-
product
SCR CONTROLLED DC POWER SUPPLY
74239
CEHCO P/N 74239Power Rating: 60 KWInput: 480 VAC, 3 PH, 60 HZOutput: 0 to 240 VDC, 250 Amp MaxSCR Controlled Power SupplyContactor, Start/Stop Control, Thermal Protection includedVoltage and current adjust availableFull operation and maintenance provided
-
product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
High Voltage SCR Controlled Power Supply, P/N 18278PS Power Rating: 350 KW. Input: 480 VAC, 3 PH, 60 Hz Output: 0 to 5000 VDC, 70 Amps max Ripple: 2 % approximately at maximum rated voltage Configuration: 12 pulse externally SCR controlled rectifier system Protection Devices: Input contactors Overload relay shutoff Input surge suppressor Thermal switches Output current limiting resistor (made with 5 Ohm Kanthal heating element) Emergency power shutoff Cooling: Each 6 pulse rectifier assembly is cooled by three 10” fans Interface: 4/20 ma converter interface for output voltage and output current to SCR controller. Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier. Weight: Approx. 5000 lbs. SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack. Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configuration Rectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure. Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
product
Safety Test Panel for Luminaire Fixture
SCR ELEKTRONIKS introduces Safety Test Panel for Luminaire with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing.
-
product
5000 AMP DC Rectifier - Air Cooled, P/N 6037C1
Air Cooled SCR Controlled Power Supply, 50 KW, P/N 6037C1Input: 480 VAC, 60 Amps, 3 PH, 60 HzOutput: 6 to 10 VDC, 5000 Amps maxContactor and overload relay are installed for protectionStart / Stop capabilityEPO capabilityManual voltage control and current limitOutput voltage and current are displayed on the voltmeter and ammeterIndoor enclosure, 68″H x 65″W x 36″DAll input/output connections are inside the enclosuresEstimated weight: 1000 lbs.
-
product
SCR Rectifiers
SCR-controlled rectifiers are electronically controlled via analog signals for constant voltage and current control. The compact and service-friendly design complies with high industrial requirements and guarantees excellent operational reliability.The input voltage can be from 208 VAC to 600 VAC, 3 PH, 50/60 Hz. Maximum output voltage can be from 6 VDC to 600 VDC. Maximum output can be from 1000 Amps to 100000 Amps. These units can be air cooled, water cooled or oil cooled.
-
product
Atlas SCR Thyristor and Triac Analyser
SCR100
Thyristors and Triacs need special test conditions to analyse effectively - that's where the new Atlas SCR comes in. The SCR100 can apply gate test currents from 100µA up to 90mA (with test load currents of up to 100mA) so it's not limited to sensitive parts.It will automatically identify the type of part (Thyristor or Triac), identify all three leads and also categorise the gate sensitivity. This new version takes a standard Alkaline AAA battery.
-
product
Endurance Test Panel For Domestic Mixer
SCR ELEKTRONIKS have developed ENDURANCE TEST PANEL FOR MIXER for carrying out endurance test of mixer at final stage. It consists of Voltmeter, Ammeter, Wattmeter & Temperature Indicator for observing the values of different parameters. Output Socket is provided for quick connections and disconnections of the equipment to be tested. User friendly operations make the equipment to be handled easier for any operator.
-
product
MCB Endurance Test Bench
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
