Filter Results By:
Products
Applications
Manufacturers
Test Harness
See Also: Harness Test, Harness, Harness Testers
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
PC Controlled Low Voltage Testers
PC Based Testers Low Voltage Introduction. The PC based analyzers provide high-speed testing for wire harnesses, backplanes, and printed-circuit boards.
-
product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
product
ATE & Test Systems
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
product
Modular Test System
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
product
Custom Wiring Harnesses and Cables
From flight critical aerospace wiring harnesses to discrete wire assemblies, WinSoft can meet your toughest requirements. Each of our finished cable assemblies and wire harnesses is built to the customer exact specifications and is 100% quality tested. Cable and harness assemblies are certified to meet all customer requirements and applicable industry standards while manufactured to strict ISO processes and procedures.
-
product
Sefelec Harness Testers
Partech Systems Australia and SEFELEC France have formed a partnership to provide a more efficient service to our Australian Customers. Our common goal is to provide our customers with a total solution to cable testing and harness testing in the manufacturing and through life support realms.
-
product
Ada Embedded Software Test Solution
VectorCAST/Ada
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing Ada software components necessary for validating safety- and mission-critical embedded systems. VectorCAST/Ada parses your source code and invokes code generators to automatically create the test code (stubs and drivers) required to construct a complete, executable test harness.
-
product
Communication Protocol Test Harness
Simulate Master or Outstation Devices.Monitor Communications.Create Custom Functional Tests with any .NET programming language, Python, or Tcl/Tk scripts.Exercise a device as it will be used on the utility SCADA network.Automatically Perform Conformance Test Procedures.
-
product
Interior Wiring Testing
With automotive interior designs becoming more luxurious, cabin space features such as ambient lighting and seat / steering wheel controls have increased the demand for interior wiring testing. Jackmark Engineering has years of experience supplying test equipment for instrument panel manufacturers and have increased their portfolio to include all aspects of interior wire harness testing.
-
product
SilverCreek SNMP Tests
Set up in less than five minutes - Windows or LinuxCustomize tests via Wizards, Script Generators, and moreAutomate operation with unambiguous test resultsIntegrate with other test harnesses and test toolsIncludes conformance, compliance, vulnerability, robustness, stress, and performance testingInvestigate failures and quickly resolve them with powerful diagnostic and analysis tools
-
product
Threaded Probes Designed for Connector and Harness Test
Equip-Test Threaded Probes Designed for Connector and Harness Test
-
product
PCB Test Fixtures
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
product
Switch Probes
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
product
Cable Harness Test System
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20,000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
-
product
Handheld Wiring Analyzer
HT-128
Simplify your wire harness testing. The DIT-MCO HT-128 provides a superior solution for point-to-point continuity analysis. These lightweight, handheld units can serve your diagnostic needs from product development and benchtop testing through field support and maintenance.
-
product
Test Management Software
Easy to use to minimal training. Our Test Management Software is powerful enough to accommodate all of your electrical and function testing requirements, whether testing a cable harness or fully equipped vehicle or aircraft.
-
product
Cable Tester
FST-500 High Voltage Cable Tester is a modular and customizable cable tester that can be easily adapted to various cable test or cable harness test applications. The electronics is based on Finero’s rugged industrial grade FST range of standard test equipment. All set and measured values are shown on alphanumeric display, additionally there is an analog panel meter for output voltage. Other cable paramerter like L, C and R can also be tested by using optional test and measurement equipment. The tester can be ordered with a build in PC and it can be used in conjunction with Finero’s Quality Control software.
-
product
NI Automated Test Software Suite
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
product
Test Workflow Pro
Test Workflow equips engineers with application-specific tools so that they can choose the right one for the job—from graphical programing environments to no-code and interactive software applications. Engineers can use Test Workflow software to perform quick ad-hoc tests, build an automated test system, automate data analysis and reporting, develop test sequences, and more.
-
product
Test Instruments
Test instrumentation from COTS to custom, including VXI, PXI and LXI-based platforms.
-
product
NI Vehicle Radar Test System
VRTS provides automated radar measurement and obstacle simulation capabilities for 76 to 81 GHz automotive radar systems. With VRTS, you can perform precision RF measurements and simulate a wide range of test scenarios for radar hardware and software subsystems, including sensors, advanced driver assistance systems (ADAS), and embedded software. Use VRTS for all phases, from design to manufacturing, of ADAS and radar system test.
-
product
EV Power Components End of Line Test Platform
Test and Validate all EV Power Electronics with One Flexible and Scalable Solution
-
product
Semiconductor Testers
Our integrated team of semiconductor test innovators delivers a complete system tailored to achieve your specific objectives, incorporating:Test strategyHardware designSoftware development and integrationManufacturingInstallationProgram managementOngoing support
-
product
Audio and Acoustic Functional Test Solution
With the growing popularity of Internet of Things devices worldwide, many electrical products are adopting voice commands as their user interface. This means that acoustic and audio test challenges are likely to impact more products than ever before. Test teams must meet extended test coverage requirements to ensure product quality while maintaining throughput and operational efficiency. For a solution to meet these sorts of demands, it must:
-
product
VLSI Test System
3380
The 3380 VSLI test system equipped with a maximum of 1280 I/O channels, 256 VI sources, flexable architecture and comprehensive optional function boards (ADDA/Hi-voltage DPS) can meet the high parallel multi-test tendency.
-
product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
product
SoC Test Systems
Specifically designed for high-throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses. With the full functions of test capability, high accuracy, powerful software tools and excellent reliability, 3650-EX is ideal for testing consumer devices, high-performance microcontrollers, analog devices and SoC devices.
-
product
NI's Electrical Functional Test Solution
PXI instrumentation ensures complete and accurate test coverage with a modular architecture mounted in ultra-reliable PXI chassis.TestStand and LabVIEW software provide rapid development of complex test steps and sequences. PXI systems conserve floorspace because of their small, light form factor. Order them preassembled and installed using NI ATE Core Configurations.SystemLink™ software deploys updates and democratizes data insights to optimize operational efficiency.
