Filter Results By:
Products
Applications
Manufacturers
Totalizers
-
product
Total Sulfur Analyzer
Model T108
Teledyne Advanced Pollution Instrumentation
The Model T108 Total Sulfur analyzer is designed to measure mixed sulfur impurities, collectively referred to as Total Sulfides, in air or carbon dioxide gas. Since there is no scrubber in the system, the instrument reading is the sum of the oxidized sulfur compounds and SO2.The Model T108 consists of a modified Model T100 SO2 analyzer with special software and a Model 501TS high temperature thermal oxidizer. Sulfur compounds are heated as they pass through the converter and oxidized into SO2. When analyzing CO2, which generally contains no oxygen, approximately 6% O2 is added to the sample before entering the converter. This dilution is corrected in the calibration procedure.
-
product
Integrating Spheres - Luminous Flux Measurement For LEDs And Lamps
Konica Minolta Sensing Americas, Inc
One of the most important tests in light measurement is the assessment of the total radiant power or luminous flux of light sources using integrating spheres. An integrating sphere’s inside surface is coated with a diffusely reflecting material which guarantees complete integration and homogenization of the emitted radiation. The integrated light is then measured at the detector port.
-
product
Air and Thermal Management
Honeywell Aerospace Technologies
Honeywell's range of electronic and electro-pneumatic systems for air and thermal management are proven to deliver highly reliable and efficient operation with lower total costs of ownership for aircraft operators.
-
product
High Voltage Diode Assemblies
High voltage diode assemblies are built by adding diodes in series to yield a higher peak inverse voltage. For example, if each diode is rated for 1200 peak inverse voltage (PIV), then six diodes in series would have a total peak inverse voltage of 7200 PIV. The detailed circuit is shown below.
-
product
NI-9326, 6-Channel, 150 V, 128 kHz C Series Frequency Input Module
786999-02
6-Channel, 150 V, 128 kHz C Series Frequency Input Module - The NI-9326 is a channel-to-channel isolated frequency input module for CompactDAQ and CompactRIO systems. This module includes six differential input channels with a 0 Vrms to 150 Vrms input range. The NI-9326 also features configurable thresholds for connection to a variety of variable reluctance sensors, single channel encoders, and hall-effect sensors. You can use the included embedded counters to perform frequency measurements or edge-counting for tracking total counts on a periodic signal. Additionally, the NI-9326 supports configurable Butterworth filters to help you perform low-noise frequency measurements.
-
product
Silicon Detectors
Through the photovoltaic effect, detectors provide a means of transforming light energy to an electrical current. The root of the theory behind this phenomenon is a small energy gap between the valence and conduction bands of the detector. When light, with enough energy to excite an electron from the valence to the conduction band, is incident upon the detector, the resulting accumulation of charge leads to a flow of current in an external circuit. Since light is not the only source of energy that can excite an electron, detectors will have some amount of current that is not representative of incident light. For example, fluctuations in thermal energy can easily be mistaken for light intensity changes. A variety of these "non-light" contributions are present and, when summed up, make up the total noise within the detector.
-
product
InfiniiVision Oscilloscopes
3000T X-Series
100 MHz - 1 GHz, DSO and MSO models Speed testing with simplified operation and documentation enabled by the 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone Touch Triggering See the most signal detail with 1,000,000 wfms/s update rateQuickly modulate and characterize signals with built-in WaveGen 20 MHz ARB, 3-digit voltmeter and 8-digit frequency counter & totalizer options Decode serial busses faster with hardware-based serial analysis options Protect your investment with full upgradeability
-
product
Leather Testing Machine
Dongguan Kejian Instrument Co., Ltd.
Test method uses clean ball placed within the material applications, steel ball itself of the impedance and total weight, must be in conformity with the provisions, on this condition detection material zigzag waterproof penetration index, using the latest inductive components and special design, test as long as materials applications in water infiltration immediately automatic stop counting or in setting time (test times) arrived, namely automatic stop and display the time or times.
-
product
External Injection Module
EIM-1000
ATOM offers tools and accessories to meet the growing challenging needs and demands of the analytical world. The ATOM EIM-1000 External Injection Module is built for safe, fast and reliable handling of gas and LPG samples with seamless integration to the ATOM XT-2000 laboratory total sulfur – total nitrogen analyzer. The efficient and compact design reduces required benchtop space to a minimum, while allowing easy access to internal module components.
-
product
Solar Total Pyranometers
SK08 & SK08-E
The Middleton SK08 is an affordable pyranometer for the measurement of global solar irradiance on a plane surface. It meets the international accepted specifications for a good quality pyranometer. The SK08 incorporates a passive thermoelectric sensor. The SK08-E version has an inbuilt signal amplifier.
-
product
Instruments / Displays
Titan’s Pulsite® instruments – the Pulsite® Solo and Pulsite® Link – interface with flow measuring elements to provide useful output readings or parameters. This is either in the form of locally displayed flow rate and total indication or analog outputs connecting to the computer.
-
product
Electrical Safety Multi-Analyzer
TOS9300 Series
The TOS9300 series is a high performance electrical safety analyzer that complies to a wide range of universal standards. Hipot, Insulation Resistance, Ground Bond, Leakage Current (touch current and protective conductor current) and partial discharge can all be tested. A total of 6 models are available for standard compliance tests in a wide variety of applications including R&D, quality assurance manufacturing lines and laboratory tests.
-
product
Total Organic Carbon Monitor
HT-110
The continuous online TOC-Analyzer HT-110 is suitable for the measurement ot total organic carbons in Purified Water (PW), Water For Injection (WFI) and Highly Purified Water (HPW). The unit is operating according to USP 643. It is applicable for pharmaceutical and/or semiconductor manufacturing. The measuring principle is based on UV-Oxidation and measurement of the difference in conductivity. TOC concentration measurement (TOC concentration 500 ppbC or lower) is necessary to perform quality control according to GMP (Good Manufacturing Practice).
-
product
Produce Quality Meter
F-750
The F-750 Handheld Brix & Dry Matter Meter uses near-infrared (NIR) spectroscopy to estimate quality metrics such as dry matter, Total Soluble Solids (TSS or brix), titratable acidity, and color. Working like a high-powered flashlight, the F-750 sends particles of light into a commodity, then measures the NIR light interactance with molecular components inside of the commodity to quantify user-selected traits. The F-750 has a wide range of applications, from determining optimal harvest timing by assessing fruit maturity, to providing an objective analysis of produce quality of fruit in packing houses and upon import. The F-750 is a handheld, fully integrated system, allowing users to operate it out in the orchard or inside the QA lab. Its simple, intuitive user interface makes it easy for anyone to use, while its model building software makes it customizable and versatile.
-
product
Energy Meters
Contrel Elettronica s.r.l. Company
Energy meters for efficient management of energy consumption. Total and partial energy meters (resettable). Equipped with input / output and communication module. From direct single-phase connection in a single module to three-phase wiring via CT. High precision. MID versions: certified energy meters for sub-measurement.
-
product
Machine Pass Off Support
Metrology Software Products Ltd
Get total peace of mind. With the Machine Pass Off Support we'll show you just how capable your new machine tool is, before it leaves the manufacturer.
-
product
Two Phase AC Motor Drive
MS 2014
Excellent High Speed Response. With help of semiconductor high end motion control algorithm and advanced common gain concept, a high speed response is achieved, therefore satisfying all motion control needs. Built-in Accuracy Improvement Features. Drive include features to improve total positioning accuracy of the mechanical system.
-
product
Electronic Control Unit Functional Test
End-of-line tests are critical to ensure passenger safety in the era of smarter vehicles. A flexible test solution is needed to ensure extensive test coverage and high test throughput with a low total cost of ownership.
-
product
- RS-232 Opto Isolation Module
Model 268
FEATURES: Total Electrical Isolation; Eliminates Noise Problems; Eliminates Ground Loops; Use for Data & Control; UL Components. The Model 268 Opto Isolation Module provides a communications link that has no electrical connections from one port to the other.
-
product
Autoranging System DC Power Supply, 200 V, 70 A, 5000 W, 400 VAC
N8941A
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
product
VisualIMPACT Software
CEAST VisualIMPACT software is designed to control CEAST Pendulums and Drop Tower Series, manage tests and offer a user-friendly interface when using the Data Acquisition System. It records force and absorbed energy data related to impacts, visualizes and helps analyze the results and calculates resilience. The operator is guided through parameters setup by means of tables describing strikers and specimens that are filtered according to the test type and international standard selected. In the case of instrumented tests, many possibilities for data analysis and visualization are made available. The results are shown through comprehensive and customizable graphs and can be filtered by break type (only specimens with a selected break type are shown). Working with groups of test, the software performs a statistical analysis, and the operator can pick and discard single test results. Different measurement units can be selected. It is possible to print reports and to export data totally or partially. Recent improvements include the possibility to set a number of user profiles, including graphic settings, default printing options, advanced parameters for data analysis and so on, switching quickly from one another when looking at results. The introduction of a new Data Acquisition System (CEAST DAS 64K) in the Impact product line has also triggered a number of new capabilities for the SW, which is now able to process a more comprehensive calibration file for instrumented tups and hammers and manage DAS configurations with a wider range of data acquisition channels.
-
product
Sawmill Green Lumber Sorting System
The transverse sawmill meter sorts pieces into four moisture groups with similar drying characteristics by assigning a dry-ability index number. This critical first step in end-to-end moisture control improves kiln performance by reducing aggregate standard deviation and total drying time when compared to unsorted loads.
-
product
UV Fluorescence TRS Analyzer
Model T102
Teledyne Advanced Pollution Instrumentation
The Model T102 TRS analyzer uses the proven UV fluorescence principle to measure Total Reduced Sulfur at levels commonly required for ambient air monitoring.The Model T102 uses a high temperature external converter set at 850°C to allow conversion of H2S, methyl mercaptan, dimethyldisulfide, and methyl-disulfide to SO2 at this temperature with efficiency greater than 98%. A switching option alternately measures TRS and SO2 while showing both readings concurrently on the front display.
-
product
Torque Instrument
DTR is a microprocessor based digital indicator, totally autonomousand with input for strain gauge based torque transducers.A ≤±0,02% accuracy makes it possible to be used use in qualitysystems as first or second line sample, periodically calibrated by aSIT center. Measuring system consists of a particularly long-termstable analogue section, of a carrier frequency amplifier whichminimises thermal drifts and of a 16 bits A/D converter whichensures 65.000 internal divisions.
-
product
AC Electronic Load
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
product
Dechlorination Analyzer
Deox/2000®
The Deox/2000® measurement module is a versatile, accurate and reliable on-line instrument for the continuous measurement of SO2 and total chlorine residuals in waste water treatment plant effluent
-
product
Flexible Implantable Microprobe
IT-18(10 FOOT)
IT-18(10 FOOT) Flexible Implantable Microprobe with 5 foot lead - Implantable in semi-solids and tissue with 18 gauge needle (supplied). Also for immersion in various solutions and rectal temperatures of small animals. Totally sheathed in chemical resistant Teflon™. Quited rugged. Maximum Temperature 150°C . Isolated. Probe diameter .050" (14 gauge represents the needle gauge that the probe can be inserted through). Time constant 0.3 seconds.
-
product
RS-422/RS-485 Repeater
ND-6510
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
Flying Probe Tester
FA1811
Designed specifically for package board testing, the FA1811 achieves both high-precision contact with a total probing precision of 10 μm, and a testing speed rivaling generic flying probe testers to meet ever increasing demands for greater analytical power, faster testing speeds and reduced costs.
-
product
Thuraya Interception System
The Strategic Thuraya Monitoring System is designed to monitor Thuraya Satellite Phones operating on Thuraya-2 or Thuraya-3 Satellites network. The System is capable of providing both sides of the communication (full duplex call), call related information (CRI) along with the location of the Thuraya Phone by monitoring of both L & C-band. The Monitoring of L-band (between Thuraya satellite and Thuraya mobile) and C-band (between Thuraya Satellite and Thuraya Gateway), provides total traffic monitoring of the targeted spot beams each of which are nearly 350 - 400 Km. Normally 7 spot beams are available at any location under the Thuraya footprint.
