Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
LXI 2.4GHz 50ohm 32x4 Matrix
60-772-001
The 60-772 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 4 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281B
The Keysight P281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
Cable Harness EM Solver
MHARNESS
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
product
Coaxial Switches
An electromechanical switch made primarily for routing microwave signals/RF energy from one point to another within a transmission line. Coaxial switches can be used in either an industrial environment or in the lab. These electromechanical devices are also used for RF testing equipment and in large RF communication systems and networks. Coaxial switches vary by port configuration, switch type, maximum frequency, isolation, insertion loss, voltage standing wave ratio (VSWR) and package type. Coaxial switches are able to route RF signals over a broad bandwidth from DC to 40 GHz, and are now offered with the Low PIM option which will improve Passive Intermodulation levels from -110dBc (standard switch) to -160dBc.
-
product
2M E1/Datacom Transmission Analyzers
GQ-4300D Series
Shenzhen Guoqin Technology Co., Ltd
GQ-4300D Series 2M E1/Datacom Transmission Analyzers is mainly used for measuring of the error rate of data communication and for the analysis of line fault and causes, and very suitable for the parameter measurement and routine maintenance testing of 2M system, N×64K communication channels
-
product
Radiation (EMF, Nuclear, RF)
Sper Scientific radiation meters measure EMF, Nuclear, and Microwave radiation levels. Whether you are, measuring the RF strength of Wi-Fi and LAN network, or the electromagnetic field emissions from electrical power lines and transmission equipment, computers, HVAC, audio/video, and other electrical appliances. Our meters are small and light enough to go anywhere, yet sensitive enough to detect minuscule amounts of gamma, beta or X-rays.
-
product
ESD Testing & Latch-Up Testing Services
EAG is an industry leader in ESD testing (Electrostatic Discharge) and Latch up testing. Our highly experienced engineering team use their industry leading knowledge and years or real world experience of the latest semiconductor technologies, circuit design, and device physics to optimize our customer's ESD and latch-up results. Human Body Model (HBM) and Machine Model (MM), Charged Device Model (CDM), Latch-up, Transmission Line Pulse (TLP).
-
product
LXI WTB Terminator, 109.8 ohm
60-983-003
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
product
Versatile, Heavy-duty Hydraulic Test Centers
HTC Series
For powertrain testing it’s all about fast and exceptional results achieved in the safest manner possible. Our Hydraulic test stands HTCs offer full functionality to test all types of transmissions, motors, cylinders, valve blocks, torque converters and pumps. As you evaluate your needs for heavy-duty mobile testing equipment, consider how upgrading to the latest technology can improve your bottom line.
-
product
Step-Tunable Laser Source, High Power and Low SSE, Basic Line
N7779C
The new N7779C basic line step-tunable laser source is ideal for cost-effective testing of broadband optical devices. It can also serve as a highly stable, tunable local oscillator for receiver testing or transmission experiments.
-
product
Directional Couplers
Pasternack directional coupler category is passive devices that couple part of the transmission power in a transmission line. Our directional coupler series provides the bandwidth, high directivity and higher power that engineers need for their most demanding application designs. RF directional couplers often use two transmission lines set close together so that energy passing through one is coupled to the other. Many Pasternack directional coupler components are RoHS and REACH compliant. RF directional couplers are available with 4.1/9.5, 4.3-10, 7/16 DIN, Type N or SMA connectors. Our directional coupler line has 6dB, 10dB, 15dB, 16dB, 20dB, 30dB or 35dB coupling values. Power ratings of our typical and high power directional couplers range from 25 Watts to 70 Watts. Directional coupler frequency range of this product design is from 1 GHz to 8 GHz. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this directional coupler series is in-stock. Not only are these couplers in directional design in stock, they also will ship the same day as they are purchased.
-
product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
Impulse Semiconductor High Current Integrated
Transmission Line Pulse Test System
The Impulse Semiconductor High Current Transmission Line Pulse (TLP) test system is the tool of choice for extracting ESD parameters for transient protection devices in a package, or at wafer level. With accuracy better than 100 milliohms at 40 amps peak current, the Impulse high current TLP is specially tailored to the needs of today's ESD device designers who must accurately measure low values dynamic resistance irrespective of breakdown voltage.
-
product
Magic Tee
MHTXE
The MHTXE Magic Tee Hybrid Couplers for millimeter waves are matched power dividers for variety of applications (general purpose power splitters, power combiners, phase measurement circuits, phase / frequency discriminators). The MHTXE Magic Tee Hybrid Couplers are available in waveguide bands between 33 and 170 GHz. These couplers are four-port transmission line components with a port configuration as shown in figure. Operation bandwidth is limited to 20÷90% waveguide operation frequency range depending on performance specifications.
-
product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281C
The Keysight P281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
EMI Receiver
KH3939
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.
-
product
Power Detectors
Macom Technology Solutions Holdings Inc.
MACOM’s power detectors are broadband devices that have integrated low loss directional couplers and built-in temperature compensation circuits. These detectors provide an easy way to monitor the power of a signal travelling in a specific direction along a transmission line. These detectors are conveniently housed in miniature lead free plastic surface mount package. Typical applications include; Power monitoring and leveling in Point-to-Point radios, IMS, Radar, VSAT, EW, Aerospace and Defense Systems.
-
product
Traveling Wave Fault Locator
XC-2100E
XC 2100E, a Fault Location System based on principle of travelling wave detection is the solution to above problem. It can detect not only permanent fault, but also transient fault within one tower span accuracy (with best accuracy of ±50 meters). It is a kind of Line Monitor for continuous monitoring of transmission lines and gets triggered whenever travelling waves are generated on line due to switching, lightening or fault.
-
product
2.5G DPSK Demodulator
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5, 10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systems utilized in commercial, defense and space exploration markets. The device plays a key role in improving signal quality and performance to meet the expanding demand for higher data rates and more complex transmission formats within current and next generation systems without major capital expenditure. Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. Themeasured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarizationdependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
product
Micro-ohmmeters
MMR-650
Designed to measure very low resistances of both resistive and inductive types of objects, including amorphous core transformers. This product is made to be used in power plants, railways and maintenance companies, to measure welded and soldered connections, equipotential bondings, earthing conductors, contacts, bolted connections, windings of motors and power transformers and other resistive and inductive objects. MMR-650 can be also utilized on a production lines (eg. at the final production control stage). An innovative combination of a high-performance measuring device with a modern user interface and advanced data management system. Wireless data transmission, enhanced system of 2D codes and ability to print labels to identify test items, all contribute to bringing new quality of work and allow the user to perform a wide range of measurements.
-
product
Balanced Measurements
The unbalanced interface of a VNA is not very well suited for measuring balanced circuits like antennas, transmission lines or chip impedances. In fact it is nearly impossible to get a decent calibration on a balanced 2-port measurement using coax cables.
-
product
EMCTD Broadband RF Safety Systems
The EMCTD analog Smart Fieldmeter® is easy to read and to operate. The EMCTD broadband electromagnetic probe covers the 0.2 to 3000 MHz spectrum where most common industrial, communications, medical and government RF emitters are found. The ANGPE-3000 system enables checking of home, office, and workplace RF levels. The system is designed to conveniently measure RF levels around WiFi access points, RFID systems and rooftop antennas; to find transmitter cabinet radiation, locate transmission line leaks, to identify non-radiating antenna elements, and much more. With the supplied NIST-traceable calibration, this system supports laboratory testing of RF devices in compliance with present EMC and RF safety standards.
-
product
Portable Meters and Components
88960
The Coaxial Dynamics 88950 and 88960 series of High-Power Meters are designed to measure RF power in 50-Ohm 1-5/8 to 6-1/8 inch coaxial transmission lines. These are the same meters included in our 81100-A, 81300-A, 81400-A and 81600-A High-Power Wattmeters.
-
product
LXI 2.4GHz 50ohm 24x16 Matrix
60-770-002
The 60-770 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
product
High Level of Customization at an Affordable Price
TLP
The Impulse transmission line pulser (TLP) discharge networks are easily integrated with other instruments for a custom system matched for your device and process applications. Specifications include 1-10 nanosecond rise times, up to 40 amps peak, for 10-500 nanosecond pulse widths. It is a proven design incorporating 15 years of hardware and device development experience. Reliable performance over hundreds of processes, and thousands of products. All TLP systems are built by special request, contact us with your specifications or application.
-
product
Transmission Line Parameter Test System
HTXL-Y / 421
Wuhan Huatian Electric Power Automation Co., Ltd.
Field test of various high-voltage transmission line power frequency parameters of high-precision test instruments.
-
product
LXI 2.4GHz 50ohm 24x8 Matrix
60-771-002
The 60-771 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 8 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
-
product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
LXI WTB Terminator, 90.6 ohm
60-983-002
The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change the signal amplitude along the cable and generate timing jitter or trigger errors. The 60-983 is a simple terminator that can be placed at each end of the WTB chain to correctly terminate the transmission line with minimal reflections.
-
product
Transmission Control
Schweitzer Engineering Laboratories, Inc.
Transmission control systems provide flexible local control and SCADA integration for substation and line protection assets, improving your system’s reliability and efficiency.
