Lisun Electronics Inc.
A leading manufacturer of lighting and electrical test instruments.
- 86(21)5108 3341
- SalesSH@Lisungroup.com
- 113-114, No.1 Building, Nanxiang Zhidi Industry Park
No. 1101, Huyi Road, Jiading District
Shanghai, 201802
China
-
Product
Optical Radiation Safety Test
EN62471-C
-
IEC62471-2006(CIE S009) Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
Product
Pocket Brightness Meter
PHOTO-100L
-
• Measuring range: 20cd/m2~2000kcd/m2; • Testing accuracy: Class 1; • Display refresh rate: 1times/sec; • Power source: 9V battery; • Power consumption: less than 20mW; • Normal technical specifications: 1) Temperature: 0~40℃, 2) relative humidity: less than 90%
-
Product
LMS-7000CCD Spectroradiometer
LMS-7000
-
LMS-7000 CCD Spectroradiometer is applied with TOSHIBA TCD1304DG linear array CCD detector, measurement speed is very quick and cost-saving.• The following wavelength range is with 0.8nm FWHM: • Integrating time is 1ms to 60s • CCD Detector is 3648pix which size is 8μm×200mμm • SNR (Signal to Noise Ratio) is 1000: 1 (Full range). A/D is 16bit • Communicate with PC by USB2.0. The software has a rich re-develop platform which can be run in WinXP and Win7. • Optical port is SMA905
-
Product
Spectrophotometer & Integrating Sphere Test System
LPCE-1
-
This Test System is suitable for photometric and colorimetric measurement of luminaries such as Energy-saving lamps, Fluorescent lamps, HID lamps (high voltage sodium lamps and high voltage mercury lamps), CCFL and LED. The measured data meets the requirements of CIE and IES LM-79 for the measurement of photometry and colorimetry.
-
Product
Electronic Ballast Analyzer
WT3000
-
• It has 8 windows to display each parameter of input and output characteristics • Frequency response for testing input current up to 1MHz, suitable for precise testing of various kind of electronic ballast • WT3000 has expanding analysis for envelope wave. • Symmetry analysis for envelope wave’s crest factor of lamp current • Sampling at ultra-high speed, dynamic analysis single frequency curve, highest sampling frequency is up to 10MHz • Portable with built-in chip micro-processor, particular suitable for development and spot production • RS-232C standard interface can be connected to PC, English version software can run in WinXP or Win7
-
Product
Plug and Switch Testing
-
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right.
-
Product
Load Cabinet
DFX-20
-
• Working power: AC220V 50Hz • Normal load: Continuous adjustable from 0 to 280V • Electric current: 0～20A/Continuos adjustable cosφ: 0.3-0.96 under 16A; 0.6~0.96 more than 16A • Precision: 0.5 class, digital display • Counter: 0～999999 times, can be preset
-
Product
Constant Temperature Integrating Sphere
IS-*MT
-
According to requirement of IEC standards, the standard test temperature is 25℃, but high power lamps such as HID lamps and LED outdoor luminaires will produce a lot of heat during the test, thus the temperature inside the integrating sphere can not meet the requirements of IEC standards. Lisun Group designed the Constant Temperatured Integrating Sphere which allows the lamp was tested in a constant air temperature.
-
Product
Power Cord Bending Tester
SW-6
-
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
Product
Digital Power Meter (Harmonic Analyzer Model)
LS2010
-
• Measure Vrms, lrms, W, PF, Hz; • Harmonic distortion analysis for voltage & current, display total harmonic and 0-50 times; • Component harmonic, selectable for absolutely or relatively harmonic display; • Voltage range: 10.0-600.0V, Current range: 0.010-20.00A, Auto range; • Accuracy: ± (0.4%reading + 0.1%range + 1digit); • Simultaneously display Vrms, lrms, W, PF value on 4 windows, suitable for production line; • Can test every kinds of curve; Print both data & curve; • Communication port for PC, run under WinXP or Win7.
-
Product
Impulse Test Generator
SUG-CCITT-A
-
Impulse Test Generator SUG-CCITT-A (1a. 10/700us, 6KV, figure is according to N.1 in IEC60950-1:2005 Annex N). N.1 ITU-T impulse test generators.
-
Product
EMI Test System
EMI-9KA
-
EMI-9KA is an automatic EMI receiver. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KA is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem. The test results are according to the international format test report. The EMI Test System EMI-9KA fully meets CISPRl6-1, GB17743, FCC, EN55015 and EN55022.
-
Product
Spectroradiometer
-
Designed to have a capability of producing any visible spectral distribution, mimicking various light sources in the visible region by feedback control of the radiant power emitted by individual LEDs. This LED test system will be used as a transfer standard for photometric, colorimetric and radiometric applications.
-
Product
Digital Power Meter (High Accuracy Model)
LS2050
-
LS2050 digital power meter is a new generation intelligent product which adopts digital sampling technology to analysis of the waveform. It has the following features: • Three windows digital display which reduces reading error, intuitive and convenient • Adopts high speed MCU and high precision A/D to control and measurement • All measured data as virtual value, also suit to signal waveform distortion • Fast test • Equipped with RS232 communicate function, can use upper computer software to carry on remote operation, control and read corresponding data, the test data and waveform could be displayed in the PC, Chinese and English operation interface, high intelligent instrument • This instrument provides two kinds of method to calculate total harmonic distortion (THD), IEC and CSA.
-
Product
Electronic Ballast High Frequency Parameters Tester
UI2002A
-
• Measure Vrms, Irms, W, PF/Hz • Voltage range: 10~600V, Current range: 10~2000mA, Frequency range: 20~70kHz • Accuracy: Class 2
