Com-Power Corporation
Com-Power Corporation has been a supplier of instrumentation for EMI / EMC Testing (electromagnetic compatibility), telecommunication ( Part68 ) and product safety ( UL / IEC CSA) testing since 1989.
- (949) 459-9600
- (949) 635-0329
- sales@com-power.com
- 1679 Placentia Avenue
Costa Mesa, California 92627
United States of America
-
Product
EM Clamps
-
The EM Clamp or a Bulk Current Injection Probe (BCIP)can be used for IEC/EN 61000-4-6 tests on ports/cables for which no Coupling/Decoupling Network (CDN) is available.
-
Product
LISNs - TEMPEST
-
Com-Power TEMPEST LISNs cover 5 kHz to 1 GHz with two complementary models — LIP-120 and LIP-1000 — rated at 10 A for TEMPEST power line conducted emissions testing in classified government, military, and diplomatic environments.
-
Product
Comb Generators
-
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
Product
System Controllers
-
System Controllers feature multi-device control, variable speed control, fiber optic interface with antenna mast and turn table, full control via front panel or PC software, on-site antenna calibration, 19" 3U rack-mountable, and a 3-year warranty.
-
Product
Feed Through Capacitor
-
Feed-through capacitors with a value of 10 μF are made so that they can be used in RFI/EMI test setups like MIL-STD-461A/462A. Now, many other standards, such as RTCA DO-160G, require them to be used. In this particular application, the capacitor offers a low RF impedance across the power supply. So, a current probe can be used to accurately measure the electromagnetic interference (EMI) currents made by the device being tested.
-
Product
Conducted Immunity Test Systems
-
Conducted Immunity System (CIS) to Test According to IEC 61000-4-6. The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
-
Product
Impedance Stabilization Networks
ISN
-
Com-Power ISN (Impedance Stabilization Network) are primarily used for RF telecom conducted emission testing per EN 55022, which is one of the EMC (Electromagnetic Compatibility) phenomenon tests.
-
Product
LISNs - Single Phase
-
Com-Power single-phase LISNs cover 9 kHz to 400 MHz in five series — 1x, 2x, 3x, 4x, and 5x — with current ratings from 20 A to 100 A for CISPR 16, ANSI C63.4, MIL-STD 461, DO-160, and CISPR 25 conducted emissions testing.
-
Product
Transient Limiters
-
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)
-
Product
Turntables
-
Used for EMC testing motorized turntables TT-400X and TT-600X are used in commercial electromagnetic compatibility testing as low-profile, above-ground platforms for spinning the equipment being tested (EUT). The turntable can hold and rotate equipment that is on a desk or on the ground. The device is turned so that the position or angle at which the EUT gives off the most electromagnetic interference can be found. By using the switch on the remote, you can turn the turntable in either direction. The motor and the gear reduction drive that goes with it make up the rotation drive. These turntables are made from non-conductive weather proof materials. You can buy any kind of ramp you want to use to move heavy equipment onto the turntable.
-
Product
Antennas
-
Com-Power EMI / EMC broadband and tuned antennas cover the frequency range of 9 kHz - 40 GHz. Most electronic products are required meet the various international EMC regulatory standards before they are introduced to the market. Com-Power provides a wide range of EMI antennas and accessories. We also have the capabilities to assist you with custom EMC antennas for special applications to meet your exact needs.Contact us today to learn more about our EMC broadband test antennas.
-
Product
Antenna Mast
Automated and Manual
-
Automated and Manually Operated Antenna Masts. The Com-Power AM series antenna masts are motorized and designed for EMI testing. Antenna mast Model AM-400 allows antenna height variation from 1 to 4 meters, and Model AM-600 can vary antenna height from 1 to 6 meters. They are constructed using non conductive fiber glass material. The antenna is mounted on a one piece cross boom, which is attached to a slider assembly. The slider assembly rides over the length of the mast on delrin wheels. It is pulled by a rope and pulley mechanism powered by a electric motor. The slider assembly is equipped with a spring loaded braking mechanism to prevent inadvertent descent should the rope fail.
-
Product
Surge Generators
-
Surge Generators by Com-Power Corporation provide you to test your electronics to lightening simulation.
-
Product
Magnetic Field Generator
-
The Com-Power APF-5060 magnetic field generator is specifically geared towards generating magnetic fields for immunity testing. The APF-5060 with its corresponding loop antennas provide a standalone solution for magnetic field immunity testing as per IEC/EN 61000-4-8 and all the derived product standards.
-
Product
LISNs - Three Phase
-
Com-Power three-phase LISNs in three series — LI-3P-1X (CISPR/ANSI, 150 kHz–30 MHz), LI-3P-2X (CISPR/ANSI V-AMN, 9 kHz–30 MHz), and LI-3P-4X (MIL-STD-461, 10 kHz–10 MHz) — covering 16 A to 100 A per phase for conducted emissions testing of industrial, commercial, and military three-phase equipment in Delta and Wye configurations.
