ESD Simulators
create known values of electrostatic discharge.
See Also: ESD Test, ESD Test Systems, ESD Generators
-
Product
Signal Architect Simulator Software
GNSS
-
The GNSS Signal Architect Simulator Software is ideal for applications requiring: High fidelity simulation of GNSS signals Digital data analysis of GNSS signal effects RF signal generation through digital playback Highly repetitive testing where consistency between test runs is critical Easy to use Graphical User Interface Low initial and support costs
-
Product
Resistor Simulation Card
SET-1210
-
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
Product
Radar Power Bus Simulation
-
AMETEK Programmable Power, Inc.
Provides sequenced programmable power to a phased array radar test facility
-
Product
MIMIC SNMP Simulator
-
MIMIC SNMP Simulator creates a network of up to 100,000 SNMP manageable devices on one server. You can simulate any SNMP based device with any number of public or private MIBs to run a large variety of device configurations with your SNMP management application. It lets you generate thousands of traps to simulate disaster scenarios.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PCI Express
PCIe-DCE
-
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
Product
8 Port BRI-S/T ISDN Simulator
BRI-8ST
-
The unit has 8 S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Acceleration Simulation Mode (ASM)
-
Maschinenbau Haldenwang GmbH & Co. KG.
MAHA Acceleration Simulation Mode (ASM) Products
-
Product
Sand Dust Climatic Environmental Simulation Test Chamber
CX-SC80
-
Shenzhen Chuangxin Instruments Co., Ltd.
Sand Dust Climatic Environmental Simulation Test Chamber
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
Solar Simulator
Unisim Compact Solar Simulator
-
The Unisim Compact is a low-cost close-match solar simulator that provides the world-leading spectral match of our award winning Unisim solar simulators in a compact, bench top unit complete with IV measurement system. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. The easy-maintenance enclosure houses a TS-Space Systems 2-zone Unisim solar simulator which combines metal halide and incandescent sources via a proprietary filter system to give an AM0 close-match spectrum (AM1.5 drop-in filter sets are available). The standard system includes an embedded source meter with complete IV measurement system (Computer, GPIB interface, IV software, MS Excel), relative irradiance indicator for monitoring lamp intensity and an electrical shutter. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the solar simulator designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
PMC Module With 2 Or 4 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation Of Avionic CAN Bus Systems
AMC825-x
PMC Module
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
Solar Array Simulator
G5.SAS
-
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
Product
Standard Class AAA Solar Simulator
TriSOL TSS
-
Essential for testing virtually any material or product that is exposed to sunlight for long or short periods of time, OAI’s low-cost, Standard Solar Simulators deliver highly collimated, uniform light. Depending on configuration, output on these Solar Simulators is rated at 350W -5,000W.These Class AAA Solar Simulators feature OAI’s Advanced Uniform Beam Optics and are available with a choice of air mass filters to reproduce a wide range of solar spectra. For added flexibility, OAI’s proven lens and collimating mirror technology allows for a variety of exposure area sizes. A Class AAA Solar Simulator is an essential tool for manufacturing as well as R&D; it is indispensable in test labs, industry, and in universities. OAI Standard Solar Simulators are used in photobiology, biomedical, solar cell testing, cosmetic testing, and paints & coatings analysis. Based on 35+ years of proven UV light technology, OAI Solar Simulator Systems deliver repeatable, reliable, constant output, and measurement uniformity.
-
Product
Fast Transient Burst Simulators
FNS Series
-
A simulator to reproduce fast repetitive high frequency pulses which are generated when switching ON/OFF electric current on the inductive load. International Standard IEC 61000-4-4 defines immunity tests for power supply lines or I/O signal lines against fast transient repetitive bursts. Also adopted as a Japan Industrial Standard.
-
Product
Digital And Analog Call Simulation
-
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
Product
Environmental Simulation
-
Simulation of environment. PHOENIX TESTLAB's environmental simulation laboratory is accredited for environmental testing of a multitude of standards.
-
Product
PXI Millivolt Thermocouple Simulator Module - 32 Channel
41-760-001
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
Accelerometer Simulator
MTN/8302
-
The MTN/8302 is a battery-powered unit designed to simulate a constant current type accelerometer. It enables test and calibration of vibration monitoring equipment such as the Monitran MTN/6000 series.
-
Product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x-DS
-
A unique feature of AIM’s APE1553-x-DS modules is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
4 Port BRI-S/T ISDN Simulator
BRI-4ST
-
The unit has four S/T ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 4 Channel
43-765-004
Analog Output Module
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
2 Port 4GFC Fibre Channel ARINC818 Test, Simulator and Monitor Module For PCIe
APS-FC-2
Monitoring Module
The APS-FC-2 is AIM’s high performance PCIe module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The APS-FC-2 is a powerful State-of-the-Art 4-lane PCIe 2.0 compliant PCIe board.
-
Product
Solar Simulators
-
Abet Technologies offer a wide range of ASTM, IEC, and JIS standards compliant solar simulators ranging from 150W to 3kW with one sun or greater illuminated field sizes from 50 x 50 mm to 35 x 35 cm. The direction of illumination, traditional down pointing, horizontal, or vertical up pointing can be specified at the time of ordering.
-
Product
UV Solar Simulators
-
UV Solar Simulators - please contact the company directly for more information.
-
Product
MIMIC® Wireless Simulator
-
Mobile device and network complexity is continuously increasing due to the multitude of devices, technologies and traffic patterns. As a result, wireless equipment manufacturers must test their products from every different aspect. They need to do this to improve quality and reduce costs.
-
Product
AFDX ® /ARINC664P7 Networks Test, Simulation, Monitoring & Analyzer
ACE-FDX-3U-2
-
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 MBit/s. Versions available for both Airbus and Boeing variants of ARINC664P7. Test, verification and simulation of AFDX®/ARINC664P7 End Systems, Switches and Networks. Support for Single or Redundant AFDX®/ARINC664P7 operation. Support for Boeing ARINC664 extensions for EDE at the hardware interface layer.
-
Product
ESD & Latch-Up Test Service
-
MASER Engineering has automatic test equipment for the most common ESD test pulse models. MIL - JEDEC - ESDA - IEC standards. IC level Human Body Model. IC level Machine Model. IC level Charged Device Model. System level IEC 61000 HBM. AEC-Q100 Field Induced Gate Leakage test. Static Latch-Up test. Dynamic Latch-Up test.
-
Product
Engine Torque Pulse Simulation
ETPS
-
HORIBA has revolutionized the way vehicle manufacturers test their Powertrains and Front End Accessory Devices. The ETPS dynamometer system accurately produces torsional pulse characteristics of an engine. This new technology employs a sophisticated mathematical model to calculate the resulting torque at the output of the engine based on engine and combustion process parameters.
-
Product
Environmental Simulation Chambers
-
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
