Gigahertz Transverse ElectroMagnetic Cells
Gigahertz Transverse ElectroMagnetic cell.
-
product
Smart Card Module Test Cells
Current and voltage measures are executed on defined pins, in stable conditions.Measurements:- Open/short- Input leakage current- IDD Supply instant/average current test (static/dynamic mode)- Input capacitance @13 MHz and inductance- Retro modulation index (RMI)Test of passive devices:- Capacitors- Resistors- Resonators
-
product
Electromagnetic
Promis 10
The Promis device is a multi-frequency, multi-spacing 3 component slingram type EM System for sounding and profiling the soil. This system features a transmitter loop to produce a primary magnetic field that will induce eddy current in conductive materials. These eddy currents will generate a secondary magnetic field that will be measured with the receiver loop. This system measures the in-phase and the out-of-phase components of the secondary magnetic field.
-
product
PXI Mixed Configuration Relay Module - 11 Cells Populated
40-138-AA-BB-CC-DD (11 CELL)
The 40-138 2A Relay Module with 11 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
product
Conductivity Cell for Ultra Pure Water Measurement
9371-10D
Stainless made Conductivity cell is now available!This conductivity cell is tough to shock and the best choise to measure Organic Solvent as well as Ultra pure water sample by employing the stainless material for its body.
-
product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
product
Electric Vehicle Battery Cell Tester
MCV
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
product
Centor Touch Star R,advanced force gauge external load cell
CNR CTR
Centor Touch Star is the most advanced force gauge currently available, it has become the benchmark tool for force measurement. Functionality, accuracy formerly reserved for expensive and complex material testing equipment are now available with Force Gauges. The functionality of material testers previously reserved for research or development applications are now available to the production floor with the introduction of the Centor Touch Force Gauge.
-
product
Single Point Aluminium Load Cell
EST-5
Technopark Automation & Control
The EST-5 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 600 mm. This load cell is available in capacities 50 kg and 100 kg.
-
product
PXI Mixed Configuration Relay Module - 2 Cells Populated
40-138-AA-BB-CC-DD (2 CELL)
The 40-138 2A Relay Module with 2 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
product
Force Sensors, Load Cells, Shear Beam
INELTA Sensorsysteme GmbH & Co. KG
Exact force measurement and weight measurement
-
product
Load Cell Power Supply
MODEL PSMR
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
product
Single Point Aluminium Load Cell
EST-6
Technopark Automation & Control
The EST-6 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 600 x 500 mm. This load cell is available in capacities 500 kg and 1000 kg.
-
-
product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
product
Battery Cell Formation System
17000 series
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
product
Compression Load Cell
EST-20
Technopark Automation & Control
The EST-20 is an industry standard Compression Load Cell that can also be used in tension. This load cell can be supplied with load button and cup as well as ball and cup mounting options and is typically used on high capacity silos, hopper scales, batching systems, platform scales, force measurement and tension measurement applications. It is available in capacities from 1 ton to 50 ton.
-
product
Light I-V Testing for Solar Cells
FCT-650
Advanced analysis of solar cells including light I-V and Suns-Voc data.
-
product
Single Cell Battery Chargers
Renesas offers single-cell battery chargers that extend the life of lithium ion (Li-ion), lithium polymer (Li-polymer), and lithium iron phosphate (LiFePO4) batteries.
-
-
product
Diffusion Cell Testing
Teledyne LABS Phoenix™ Dry‐Heat Systems make diffusion‐cell testing faster, easier, and more economical. The Phoenix Systemincludes an advanced diffusion cell design. Options include the compact Phoenix DB-6 six‐cell manual sampling system and the Phoenix RDS automated sampling system capable of handling up to 24 diffusion cells at once.An important advantage of the Phoenix System is the speed with which receptor cell contents are homogenized. Visual testing with red dye placed on the surface of the media at the top of the sampling arm shows complete dispersion occurs within a few seconds.Explore the pages in this section to learn more and to configure your own system.
-
product
Industrial Weighing - Wireless Load Cells
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
product
Low Concentration Photo-Voltaic (LCPV) & High Concentration Photo-Voltaic (HCPV) Cell Testing
Concentrated PV Cell testingPhoto-biological studies of plants, animals, and cell culturesSemiconductor testingPhoto-toxicity researchMaterial degradation researchAccelerated UV and solar exposure testing of color fastness and material stability for paints, textiles and plasticsAtmospheric photochemical pollution research
-
product
Pressure Cell Transducer
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S Pressure Transducers manufactures a wide range of absolute and true gauge pressure transducers.*UNITECH’S Pressure Transducer is mainly a strain gauge based sensors ranging form Vacuum to 1200 Kg/cm2. *The stainless steel construction permits the transducers to operate in rugged, industrial environments. *We also undertake custom-built pressure transducer for specificrequirement and for OEM users.
-
product
Hydraulic Calibration for Load Cell
HLCS-10000
Jinan Testing Equipment IE Corporation
The Hydraulic Calibration System is specially designed for the calibration of load cells with higher capacity. The Calibration for Load Cell can calibrate the load cell within +/-1%.
-
product
Economical Single Point Bending Beam Load Cells
ESP SERIES
The ESP Series is a economical, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point bending beam design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The ESP Series features a moisture proof sealant.
-
product
Ultra Precision Mini Load Cell Universal/ Tension or Compression
MDB SERIES
The MDB Series Load Cells was designed to help fill the growing need for a greater selection of high accuracy load cells for use in space limited applications. The anodized aluminum MDB's are compliant in tension and compression, therefore, a good choice for in line through zero applications, as well as single direction tension or compression. Applications may include load feedback for process control, low capacity tensile testing machines, robotics, or designed into your product. Give us a call, we would be pleased to discuss your application requirements.
-
product
Load Cells
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
product
Cell Voltage Monitor
N1200 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N1200 series fuel cell voltage acquisitor is specially developed by NGI for fuel cell R&D and production. It is with compact size, high integration, high reliability and fast data transmission. N1200 standalone supports up to 200 channels. More channels can be tested simultaneously under cascade mode. Voltage acquisition range is from -2.5V to +2.5V, which completely covers the voltage range of fuel cell. Real-time voltage data of total 200 channels can be uploaded within 10ms by adopting 100M Ethernet communication. N1200 PC application software supports platform-based test applications, which allows users to customize test files based on the test requirements and process.
