-
Product
High Current SMU Family 2000 A
AXC76xx
-
Generate very short, fully regulated current pulses from 2 ms to DC with up to 2000 A. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
Product
Power Supplies
-
AC and DC power supplies are used for providing the power required for energising the trip and close coils of the breaker and for running the spring charging motor. The appropriate AC or DC configuration of the power supplies can be selected, depending on the DUT specifications of the manufacturer. Dual-mode AC/DC power supplies capable of providing AC and DC outputs from the same power supply are also available, if required by the user.
-
Product
[5kV AC/6kV DC] Hipot and Insulation Resistance Tester, Rise/Fall-Time Control Function Equipped
TOS5300 Series
-
The "TOS5300 Series" is a series of test instruments used in Hipot (withstanding voltage) tests and insulation resistance tests, two of the four tests regarded as necessary for ensuring the safety of electrical products. With an output of 5 kV/100 mA (AC) and 6 kV/10 mA (DC), the series can be used in Hipot (withstanding voltage) & insulation resistance testing of electronic equipment and electronic parts, based on the requirements of IEC, EN, UL, VDE, JIS, and other international safety standards and the Electrical Appliance and Material Safety Law. Also, the test voltage stability is improved with the adoption of a newly developed switching amplifier. Since the output voltage can be kept constant even when the AC line voltage or frequency changes, consistent testing can be performed, even when the power supply environment is in an unstable region. The TOS5300 is also equipped with a number of features that are capable of meeting a variety of test needs. It is a new low-cost standard model that provides thorough operability, reliability and safety.
-
-
Product
Life Cycle Module Testing System
LCN
-
Full featured test system for quality control and R&DLife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Calibrating Equipment
-
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Programmable DC laboratory power supplies
-
Elektro-Automatik GmbH & Co.KG
Our programmable Laboratory Power Supplies feature the Auto-Ranging Output. Owing to this special function, EA Laboratory Power Supplies are much more flexible and, in comparison to conventional power-supplies, they are able to source a much larger number of EUTs (equipment-under-test) with differing nominal voltages. Through an optimised mix of analogue- and digital technology (µ-controller/FPGA based) and combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of power-supply series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D.
-
Product
Programmable DC Load Current Waveform Generator
9923
-
9923 application software can be used to edit arbitrary waveform, providing electronic load simulation different sink current conditions
-
Product
Cable Assembly, Type-N (m) to Type-N (f), DC to 5 GHz
11501A
Cable Assembly
The Keysight 11501A is a 180 cm (71 in) type-N male to type-N female cable assembly with a frequency range of DC to 5 GHz.
-
Product
Resistivity Monitor / Controllers
750 Series II Resistivity Monitor & Controllers
-
The unique circuitry of the 750 Series II Resistivity Monitor/controllers guarantees accurate and reliable measurements. Drift-free performance is assured by “field proven” electronics, including automatic DC offset compensation and highly accurate drive voltage. Since temperature compensation is at the heart of accurate water measurement, all Myron L® Monitor/controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. The TC may be disabled to conform with USP requirements.
-
Product
110 GHz Frequency Extender, Pulsed DC Bias
N5293AX52
Frequency Extender
The Keysight N5293AX52 is a broadband frequency extension module designed for use with Keysight’s new PNA / PNA-X-based millimeter-wave solutions. It is a compact, lightweight, and ruggedize frequency extender module with built-in bias tee for pulsed DC bias operation. It interfaces with the Keysight N5292A test set controller. The modules allow users to extend the frequency coverage of a base PNA / PNA-X Series network analyzers to a range of 10 MHz to 110 GHz. For more information about cable and accessories for use with network analyzers, please visit Network Analyzer Accessories.
-
Product
DDS Function Generator
FG-3000 Series
-
The FG-3000 series function generator utilize advance Direct Digital Synthesis (DDS) technology to create highly accurate and stable output signals including sine, square, and triangle waveforms up to 20MHz with 12V peak-to-peak amplitude and DC offset variable up to ±5V in a portable hand-held unit.
-
Product
High-Performance USB-Controlled PLL Synthesizers
-
Rugged, SMA-connectorized designs that support a USB 2.0 interface with a PC supplying DC power and GUI command control. They cover a broad range of frequency bands from 25 MHz to 27 GHz. These USB-Controlled PLL Synthesizers deliver output attenuation that is adjustable up to 50 dB in 1 dB steps and high output power levels ranging from +10 dBm to +19 dBm typical. Phase noise is as low as -108 dBc/Hz at 100 MHz offset and phase locked speed is 1 msec typical.
-
Product
DC to LVDT and DC to RVDT Converters
-
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices. They provide a very precise linear AC voltage output proportionate to the magnitude of the input data, in or out of phase respective of the AC reference input as determined by the MSB of the input word (offset binary format).
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 10 A
40-666B-012
Multiplexer Module
The 40-666B-012 is a single 6-channel 10A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
Switch Mainframe
SW1002
-
Switch between voltmeter and battery tester while testing. 264 channels max. (2-wire) to 72 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
Product
Multi-Volt Twin-Lead Tester
69135
-
Checks and indicates voltage on circuits up to 460 volts, AC or DC.Tests for DC polarity, frequency, and polyphase line.Four separate bright neon AC/DC indicators indicate voltage being tested 110, 220, 277 or 460 volts.Reinforced test leads, stored in the case, and furnished with probes on the ends.Reinforced casing.
-
Product
High-performance LPDA
ALP690
-
The ALP690 is a high-performance LPDA (log periodic dipole array) antenna with a bypassable, built-in RF amplifier for use with wireless microphone receivers in location or studio production. The design delivers +4 dBd of passive gain in a directional pattern to extend operating range, and, when DC power is applied, the amplifier applies gain to overcome loss in long coaxial cable runs. By offering both active and passive operation modes, the ALP690 can be used as a receiver antenna (active or passive) and as a transmitter antenna (passive only).
-
Product
Precision DC Power Module, 60V, 17A, 500W
N6766A
Power Module
The Keysight N6766A is a 500 W precision DC power module that provides low noise, and precise control and measurements in the milliampere and microampere region with the ability to simultaneously digitize voltage and current, and capture those measurements in an oscilloscope-like data buffer.
-
Product
Locomotive Testing
DC7000
-
A purpose-built load bank for the performance testing of engines and generators of all types of diesel electric locomotive up to 4000hp rating, with easy-to-use resistance adjustments allowing tests to be carried out over the whole power envelope. Capacity 0 7000A continuously at up to 2000V DC
-
Product
Controlled Fastening Tools
-
When it comes to Controlled Fastening Tools AIMCO has a wide selection of high-quality DC nutrunners, electric and pneumatic pulse tools, tool controllers and monitors and more. We'll help you find the perfect tools to get the job done right.
-
Product
IP67 DC Blocking Splitter Combiner
PD5023
-
INSTOCK Wireless Components, Inc
PD5023 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5023 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
Product
Line Injector
J2120A
-
While the injection transformer is a very wideband adapter, it is not useful for measuring ripple rejection (PSRR) of a power supply or even an opamp. This is because the attributes that make the injection transformer perform so well also result in a transformer that is intolerant of DC current. Even very small DC currents (5mA or less) can greatly reduce the signal capacity or even totally saturate the transformer. For this reason, the Picotest line injector (J2120A) is another essential test adapter.
-
Product
Signal Spectrum Converters
-
Advanced Science and Novel Technology, Co., Inc.
DC to 5.6GHz finite impulse response filter.Two differential CML-type input ports and one differential CML-type output port.Nine analog tap-weight control inputs.Differential gain of approximately 0dB.Single +3.3V or -3.3V power supply.Power consumption: 422mW.Fabricated in SiGe for high performance, yield, and reliability.Custom CQFP 44-pin package.
-
Product
Environmental Control System (ECS) Tester
H301
-
The H301 Environmental Control System (ECS) Tester measures and displays parameters required to test and troubleshoot aircraft heating and air conditioning systems. These parameters include temperatures, pressures, AC and DC voltages, DC currents, and resistances.
-
Product
PXI 10 x DPST 8 Amp Power Relay Module
40-160-002
Relay
The 40-160 module has a choice of 10 x SPST, 20 x SPST or 10 x DPST Power Relays, suitable for switching inductive/capacitive loads up to 10A at 250Vac.Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.It is suitable for applications requiring switching of either mains voltage or DC current.
-
Product
6 Way GPS / GNSS Signal Splitter
GPS602
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Bridge Decking Testing Equipment
-
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
Product
High Power Digital Lab 500W – 1.2KW Output – Regulated DC Power Supply
LAB Series
-
- 19” Rack Adaptable- Constant Voltage / Constant Current Operation- Two Digital Meters – 3 Digit DPMs- Phase Controlled PreRegulation Plus Linear PostRegulation- Remote Sensing Facility- High Stability and Close Regulation ±0.01%OPTIONS AT EXTRA COSTa) Presetting Facilityb) Over Voltage Protectionc) 19” Rack Mountingd) Analog programming &monitoring for Voltage &Current.
