Product

Standard Mechanical Calibration Kit, DC To 9 GHz, Type-N, 50 Ohm

85032F

-

Keysight Technologies

85032F - Keysight Technologies

The Keysight 85032F calibration kit contains precision 50 ohm type-N standards used to calibrate Keysight network analyzers. Standards include fixed terminations, open circuits, and short circuits in both genders. This kit is specified from dc to 9 GHz.

Product

IQ Demodulator

IQD Series

-

EM Research, Inc.

IQD Series - EM Research, Inc.

*Capable of receiving RF and LO frequency inputs *Output from DC to 500 MHz *Internal low noise oscillator Internal reference *Buffered demodulator *Balanced IQ *Optimized for low EVm *Optional internal Reference Detect Switch (EM Research RDS Series) *Up to 250 mega-symbols per second

Product

High Voltage Probe

HVP-40M

-

PINTEK Electronics

HVP-40M - PINTEK Electronics

*DC 40KV CAT II Pollution 2*600MΩ Impedance*25KV ± 2%, 40KV ± 3%*T.C. 200 ppm/oC*Positive Polarity only.*Resolution 1KV*Need not power.*CE, TUV GS, UL, CUL, IEC1010

Product

6kW Regenerative DC Electronic Load (CC/CR/CV/CP/CC+CV/CR+CV)

PLZ6000R

-

Kikusui Electronics Corp.

PLZ6000R - Kikusui Electronics Corp.

PLZ6000R is a DC electronic load that regenerates load power to the AC line. Regular electronic loads consume load power by having semiconductor devices convert it into heat. By contrast, PLZ6000R converts load power into reusable electric power, rather than converting it into heat as is typically done, and feeds this power to the AC line, thereby substantially reducing the amount of waste energy. PLZ6000R is an environment-friendly electronic load that can contribute significantly to your energy saving efforts.

Product

Hazardous Location Syringe Pump

260HLf

-

Teledyne LABS

260HLf - Teledyne LABS

Teledyne LABS HLf-Series pumps give you the same accurate, predictable flow and pressure control as our standard D-Series, while conforming to safety standards for use in UL Class I, Division 2, Groups A B C & D, T4 environments. The hazardous location rating is achieved through internal design modifications including the use of brushless DC motors. This approach eliminates the need for purge boxes or other additional safety devices. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. If needed, optional materials such as Hastelloy C-276 are available on request. The HLf controller has a keypad and LCD, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly.

Product

Current Preamplifier

1212

-

DL Instruments, LLC

1212 - DL Instruments, LLC

The Model 1212 Current Preamplifier is designed as a low cost, gerenal purpose, benchtop instrument to provide a high performance detection system for small ac and dc currents. The 1212 operates with a virtual ground at its input which mitigates unpredictable high frequency rolloff due to input cables and stray capacitance.

Product

Ultrafast Photodetector with Current Monitor, 700 - 870 nm, DC - 12 GHz, FC/PC

DXM12CF

-

Thorlabs, Inc.

DXM12CF - Thorlabs, Inc.

The DXM12CF Ultrafast Detector is a DC - 12 GHz, fiber-coupled, GaAs-based photodetector designed for applications in the 700 nm - 870 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.

Product

Programmable Linear DC Power Supply

DP800 Series

-

Rigol Technologies Inc.

DP800 Series - Rigol Technologies Inc.

DP800 series includes single output, two output and three output programmable linear DC power supply. They have pure output, excellent performance indicators, multiple analysis functions, rich interfaces, and can meet the diverse testing needs.

Product

Bias Tees

-

Mini-Circuits

Mini-Circuits

Mini-Circuits is your complete source for bias tees, handling up to 4 Amps DC and covering 100 kHz to 12 GHz!Rugged coaxial modelsTiny surface mount packages as small as 0.15 x 0.15 inExcellent isolation50 and 75 Ohm models

Product

External DC Bias Adapter

16200B

-

Keysight Technologies

16200B - Keysight Technologies

The 16200B test fixture is designed to operate with high frequency LCR meters and impedance analyzers. It allows you to supply a bias current across the device of up to 5 Adc through a 7 mm port by using an external DC current source.

Product

CT / PT Analyzer

CTPTA-504

-

UDEYRAJ ELECTRICALS PRIVATE LIMITED

CTPTA-504 - UDEYRAJ ELECTRICALS PRIVATE LIMITED

UDEY ‘CTPTA-504 is a comprehensive CT and PT analyzer. It’s constant voltage and current is highly stable. DSP system controls the constant voltage and current source output and amplitude. This source generates AC of 0-125V and or DC of 0-0.5A current to sample CT. The DSP system besides controlling the sources, also samples data and communicates with the internal computer. Display screen is large LCD with touch pad. The analyzer is highly accurate with high noise immunity and is very user friendly.

Product

AC Power Sources

RS Series

-

AMETEK Programmable Power, Inc.

RS Series - AMETEK Programmable Power, Inc.

The RS Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the RS series combines compactness, robustness and functionality in a compact floor-standing chassis, no larger than a typical office copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the RS unit to its designated location (using included casters), plug it in, and the RS series is ready to work for you.

Product

ARM LPC2364 Board

MS 1541

-

Meltronics Systemtech

MS 1541 - Meltronics Systemtech

- 128KB On chip Flash- 16*2 line LCD Module interface- Two CAN channel at 1MPBS- Ethernet interface which supports 10/100 MBPS- Full Modem RS232 interface- RS485 interface- RTC (Real Time Clock)- 2048 bits serial EEPROM with data protect and sequential read.- 24 ULN outputs of 12V level.- Eight 110V DC inputs interface.- Six digital inputs interface- Four on board keys interface- Power delay circuit for external use- ON board inspection circuit

Product

2 in 1 LAN Tester

PLTM20

-

Pyle Audio Inc.

PLTM20 - Pyle Audio Inc.

Tests Pin Configuration for 10 Base-T, 10 Base-2, RJ45/RJ11, 356A, TIA-569A/568B and Token Ring CableRemotely Test Cables Up to 330 Yards AwayTest Ground WireMeasure DC/AC Voltage, DC/AC Current, Resistance, Continuity, and DiodeDC Voltage: Max Range 600 V, Accuracy +/- 0.5%AC Voltage: Max Range 600 V, Accuracy +/- 1.2%DC Current: Max Range 200 mA, Accuracy +/- 1.2%AC Current: Max Range 200 mA, Accuracy +/- 2.0%Resistance: Max Range 20 M, Accuracy +/- 0.8%Continuity Test: Beeps If Less Than 100 Accessories Included: Test Leads, LANtest Remote Terminator, 9V Battery, Carrying CaseDimensions: 6.38' H x 2.93' W x 1.73' DWeight: 10.86 oz.Sold as : Unit

Product

4-in-1 OSLT Calibration Kit, DC to 50 GHz, 2.4 mm (m)

CK564A

-

Spanawave Corporation

CK564A - Spanawave Corporation

The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.

Product

Power Limiter, 0.01 to 26.5 GHz

N9355C

-

Keysight Technologies

N9355C - Keysight Technologies

The N9355C power limiter provides the best broadband input power protection to sensitive RF and microwave instruments and components, like network analyzers, spectrum analyzers, and amplifiers, from excess RF power, DC transients and ESD. Minimize your measurement uncertainty and improve your measurement accuracy with the limiter's superior RF performance.

Product

Isolated RS-232

-

Analog Devices Inc.

Analog Devices Inc.

Analog Devices offers a wide range of RS-232 transceivers to suit many applications. As RS-232 cable networks and the systems to them can be vulnerable to voltage spikes and ground loops, we have developed a number of innovations that protect against these issues and create an isolated RS-232 environment. We accomplish this through our isoPower® integrated dc-to-dc converters, as well as our iCoupler® technology, which enable the power isolation and signal isolation required for system reliability in a noisy environment.

Product

Power Splitter, DC to 18 GHz

11667A

-

Keysight Technologies

11667A - Keysight Technologies

The Keysight 11667A power splitter is recommended when making wideband ratio measurements using a Keysight 8757 scalar network analyzer. This two-resistor type power splitter provides excellent output SWR at the auxilliary arm when used for source leveling or ratio measurement applications. The tracking between output arms over a frequency range from dc to 18 GHz allows wideband measurements to be made with a minimum of uncertainty.

Product

High Speed DC Electronic Load

6330A series

-

Chroma ATE Inc.

6330A series - Chroma ATE Inc.

The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.

Product

Waveguide Power Detector

-

RF-LAMBDA Inc.

RF-LAMBDA Inc.

RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.

Product

HV & AC Resonant Equipment

-

Kvtester Electronics Technology Co.,Ltd

Kvtester Electronics Technology Co.,Ltd

This kind of products are small in volume, light in weight, with compact structure and multiple function, general-purpose and easy to use. Applies to the test of frequency or insulating intensity under DC ,HV for all kinds of HV electric equipments, components, insulated material in electric system, industrial and mining enterprises, traffic , post and telecommunications, science institute, etc.