Filter Results By:
Products
Applications
Manufacturers
Gold
invaluable naturally occurring material able to withstand corrosion, highly conductive. AKA: Au
See Also: Precious Metal, Platinum, Au, Gold Test
- Virginia Panel Corporation
product
Coax, Contact, Receiver, 20/26 GHz, Flex 402
610102119
Coax contact, Receiver, 20/26 GHz, Flex 402 (Only available in patchcords).Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield-SolderInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.25 for 2 - 18 GHz1.30 for 18 - 26 GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications Flex 402 (Only Available in Patchcords)Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition AInsulation Resistance 2000 MΩ Min.
-
product
Mini Power, Contact, ITA, 65 Amp, 8 AWG
610115124
Primary mating contact 610116112. (May mate with other Receiver contacts, as well.)Mini Power contacts carry up to 65 amps continuous current, 480 VAC. Maximum resistance is 1 Milliohms.Specifications Operating Voltage & Current 65 Amps Max. Continuous – 8 AWG40 Amp Max. Continuous – 12 AWG30 Amp Max. Continuous – 14 AWG25 Amp Max. Continuous – 16 AWGContact Resistance 1 mOhms Max.Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 1000 MOhms Min.Contact Body BeCuContact Plating 50µ" Au over 100µ" NiContact Termination SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 3.37
-
product
Waveguide Bends
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
product
Grid Electrode
Grid electrode is produced by the deposition of the platinum, gold or carbon onto the quartz glass. The dimension of the glass is 8 x 27 mm, with a 1 mm of the thickness, and the grid line is 100 m width with a distance of the 150 m between lines.
-
product
WR-8 Waveguide Straight
WAG-08-SXX
Precision mmw F-Band, WR-08, Straight waveguides are built with high precision and then gold plated for high corrosion resistance. They have very low loss and great VSWR. Manufactured to rigid specifications, these transmission line components provide minimum detrimental effects on the overall system VSWR.XX = length in inchesFeatures of WR-08, Waveguide Straights• 90 GHz to 140 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-8 Waveguide Straight
-
product
Trace Level Chemiluminescence NO-NOy Analyzer
Model T200U NOY
Teledyne Advanced Pollution Instrumentation
The Model T200U NOy analyzer has been developed and refined specifically to address the challenges of NOy monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is coupled with a remote NOy converter via umbilical to allow measurements with a lower detectable limit of 50 ppt.The Model T200U NOy analyzer combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer. The remote NOy converter is provided with a stainless steel, NEMA 4X (IP65) enclosure and custom sample umbilical to allow a mounting height of 10 meters. In addition, the converter features a unique purge circuit designed to remove residual calibration gas.
-
product
Connectors, Header - Male
INT-10040
1x40 pin breakaway header. These headers have square pins and fit intostandard 0.1" breadboards. Scoring makes for convenient breaking into smaller headersfor all of your projects. Gold plated and RoHS compliant.
-
product
Miniature Adjustable Pressure Switch
MDA
Sense differential pressure with this Miniature Adjustable Pressure Switch. The switch features field adjustable set point and gold inlay contacts. Air or other compatible fluids can be used on the ?high side?.
-
product
Plugbord
3795-1
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side) on 0.100"(2.54mm) centers. 3-Hole Solder Pads One Side Only. 3-hole solder pads (0.28” x 0.080”) for interconnecting multiple component leads. All pad and bus surfaces solder coated for user convenience. No pattern on reverse side, edge contacts only. Convenient easy-to-read hole marking legend on wiring side.
-
product
Rectifier Diodes
Chip Diodes from Bourns has emerged that offers the capability to provide a silicon diode with minimal packaging overhead. The small signal 0603, 1005 and 1206 Chip Diodes are lead free with Cu/Ni/Au plated terminations while the other packages (SMA, SMB, SMC, 1408, 1607, 2010, 2419, 8L NSOIC, 16L NSOIC, SOT23, SOT23-6, 16L WSOIC) use 100% Tin terminations. All Bourns® diodes are compatible with lead free manufacturing processes, conforming to many industry and government regulations on lead free components.
-
product
Single Sided PCB
Amitron produces prototype, midrange and high volume Single Sided circuit boards, with a copper thickness from one to twenty ounces. Operating temperatures range from 130 C to 230 C. Single sided boards are available with surface finishes including Organic surface protectant (OSP), Immersion Silver, Tin, and Gold plating along with both leaded or lead-free Hot Air Solder Level (HASL).
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 305gf
K100-H080305-SKAU
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
product
Isothermal Titration Calorimeters
MicroCal ITC Range
The "Gold Standard" for measuring binding affinity and stoichiometry. MicroCal ITC isothermal titration calorimeters are used to study a wide range of biomolecular interactions. The applications range from drug design to fundamental research such as the understanding and regulation of signal transduction pathways. These systems deliver direct, label free and in-solution measurements of binding affinity and thermodynamic parameters in a single experiment. They have high sensitivity, low sample consumption and options for automation to minimize ‘hands on’ time. A choice of instruments ensures that MicroCal ITC calorimeters meet the varied and demanding requirements of today’s life science laboratories.
-
product
Power Supplies
ZPG-600B
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Power Supplies
ZPG-500B
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
product
Gold Detectors
Be prepared to dig deeper than ever before! With a Minelab Gold Detector you''ll find the elusive gold nuggets that others are missing! Minelab Gold Detectors are the FIRST CHOICE for: Professional gold prospectors, Small scale artisanal mining, Serious holiday gold prospecting, Weekend enthusiasts, Gold specimen collectors.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 155gf
K100-K150155-SKAU
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
product
PCI Adapter for cPCI
PCI2cPCI
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
product
Power Supply
NZXT HALE90 1000w
*80+ Gold certified: The HALE 90 series from NZXT operates atultra high efficiency, at 20%, 50% and 100% loads, efficiencies are87%, 90%, and 87% respectively.*Single140mm two ball-bearing fan operates with minimal noiseeven at full load. Maximum decibel levels are 20db for wattagesbetween 550-750W and 30db for 850W and above.*Strong Single Rail Design: A single +12V rail provides stabilityand ease of use making the most out of your power supply. Offers stable & clean current delivery under heavy load.*Modular cable design: Modular cable design allows the user topick and choose which cables they want to use, optimizing cablemanagement and airflow inside the chassis. Flat cables allow for easier routing and bending inside the computer chassis during wire management.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 155gf
K100-C150155-SKAU
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
product
Small Pellets Testing Kit
The ceramic pellets that generally have a diameter between 6 to 12 mm and a thickness of 2 to 4 mm are blocked on a special flange with a disc of soft vermiculite (mica) that has the same high of the ceramic sample and prevents the latter (or the flanges) to toggle. Gold or other appropriate M_Grid™ materials are placed on both sides of the pellet for potential and current measurement. After this operation, the double ceramic felt caps are covering the sample as for any other cell mounting in the Open-Flanges™ test set-up.
-
product
Environmental Water Research Optical Spectrometer for Colored Dissolved Organic Matter (CDOM)
Not just a scanning fluorometer for EEMs, but a much faster and better A-TEEM spectrometer for colored dissolved organic matter (CDOM)The HORIBA Aqualog is a unique optical spectrometer that is the gold standard in environmental water research around the world for the study of color dissolved organic matter (CDOM).
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 305gf
K100-K150305-SKAU
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
product
Signal Patchcord, ITA, Mini Power, 50u Gold, 36", 14 AWG White Teflon, Single Ended, (40 Amps)
7-239912000-036
Signal Patchcord, ITA, Mini Power, 50u Gold, 36", 14 AWG White Teflon, Single Ended, (40 Amps)
-
product
High Force Type Prbobe For PCB, K100 Series 100 Mil Pitch, Receptacle With Wire Wrap Pin
KR100-WP
K100 Series, Pitch 100mil, Receptacle, with wire wrap pin. Brass with gold finish.
-
product
PCIe Adapter for XMC
PCIe8LXMCX1
Simple and easy to use. Install PCIe8LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position.
-
product
RF/Microwave Assembly Capability
Teledyne Labtech offers a comprehensive build-to-print microwave module and microwave components manufacturing service. This includes MMIC placement, Au wire bonding, SMT assembly and test.Our microwave MIC production facility is housed in a class 10,000 clean room that accommodates manual chip placement and semi-automatic wire bond assembly. Dedicated microwave components manufacturing is undertaken within production cells established to meet specific customer or product requirements.
-
product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 43
MechanicalMINIMUM CENTERS: .075 (1.91)FULL TRAVEL: .250 (6.35)WORKING TRAVEL: .167 (4.24)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 3 amps continuous at working travel, non-inductiveRESISTANCE: At 35 mA test current,30 mOHMS meanMaterials and FinishesPLUNGER: Heat treated beryllium copper or steel hardened to 55-60RC, both 24Kt gold plated over nickelBARREL: Nickel silver with 24Kt gold plated ID and OD over nickelSPRING: Music wire, 24Kt gold plated over nickel
-
product
Socket Accessories (Thru-Hole Options)
The male pin adapter consists of standard high temperature FR4 with pressed in terminal pins and threaded inserts for mounting the socket. The top side of adapter has gold plated pads to receive socket interconnect and the bottom side has 0.006″ to 0.018″ diameter pin tails. These pins can be soldered to the plated thru holes in the target board. Then socket can be mounted to the threaded insert.
-
product
Simulators (Gen II)
J1939
The Au SAE J1939 simulators (Gen II, includes V1.00A releases and V2.00A releases) can generate SAE J1939 signal for up to three controller applications (CA): Engine, ABS and Transmission. Au J1939 simulators are designed so easy to use, even product line operator and sales personal can use them without Controller Area Network training. Au J1939 simulator can run all by itself and doesn''t require complicate software settings or user''s knowledge and experience on Controller Area Network. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
