Stripline
generate a transverse electromagnetic field for immunity testing and calibration.
-
Product
Stripline Automotive 10KHz-30MHz 50 Ohm
STPL-30
-
The GTEMCELL STPL-30 Stripline is designed to produce high electric fields over a controlled bandwidth. It is used to perform EMC measurements according to automotive and aerospace standards in order totest the immunity of automotive and aircraft equipment to radiated electromagnetic fields.The STPL-30 uses a dual-sided tapered adjustable feed design into a tunable transmission line.
-
Product
Socket with Bifurcated Contact Solder Tail Pins
Series 0511
-
Strip-Line Sockets with Bifurcated Contact Solder Tail Pins. Features: For mounting liquid crystal displays and other high pin count or odd centered components. Available in several sizes with bifurcated contacts in solder tail or wire wrap pins. Consult Data Sheet No. 12009 for wire wrap pins. Optional spacer available for mounting on .300 [7.62], .600
-
Product
Stripline 50/90 Ohm DC-1GHz Mod. STPL
-
The EMC-STPL striplines are designed for automotive immunity testing of components according to the standards ISO 11452-5 and SAE J1113-23. Striplines are a variation of TEM lines which allow an application of electromagnetic fields with a good homogeneity in the test volume.
-
Product
VME J1J2 Monolithic 2 slot
101VMEM102-0500R
-
VME J1J2 Monolithic backplane 2 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1 7 Slot with ADC Connectors
101VMEJ107-0590
-
VME J1 backplane 7 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
2-Way Power Dividers From 0.23 To 70 GHz
-
Pulsar Microwave manufactures a large selection of 2-way power dividers in narrowband and broadband configurations, covering frequencies from 225 MHz to 70 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
Product
MP field sources calibration set
-
The MP field source calibration set is used to measure electric or magnetic fields in a frequency range up to 3 GHz. RF fields or transient fields can be measured. The MP field source calibration set is used to check fields of the Langer EMV-Technik GmbH field sources, fields of TEM cells and IC striplines.
-
Product
VME J1 3 Slot with ADC Connectors
101VMEJ103-0590
-
VME J1 backplane 3 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1J2 Monolithic 6 slot
101VMEM106-0500R
-
VME J1J2 Monolithic backplane 6 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1J2 Monolithic 20 slot
101VMEM120-0500
-
VME J1J2 Monolithic backplane 20 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
Bandpass Filters
-
These bandpass filters utilize a suspended stripline design to obtain a very compact configuration. Applications include wideband receiver input preselection and output filtering of frequency multiplied RF power sources.
-
Product
VME J1 8 Slot with ADC Connectors
101VMEJ108-0590
-
VME J1 backplane 8 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1 16 Slot with ADC Connectors
101VMEJ116-0590
-
VME J1 backplane 16 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
9U CTEL Backplanes with system Slot on left 9U8Slot, 3 x P47
103CTEL908-4146R5
-
Conforms to PICMG basic specification 2.0 R3.0, Versions conforming to PICMG H.110 Computer Telephony specifications, 8-layer and 12- layer controlled impedance stripline design.
-
Product
VME J1J2 Monolithic 1 slot
101VMEM101-0000
-
VME J1J2 Monolithic backplane 1 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1 21 Slot with ADC Connectors
101VMEJ121-0590
-
VME J1 backplane 21 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1J2 Monolithic 17 slot
101VMEM117-0500
-
VME J1J2 Monolithic backplane 17 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
Beam Lead PIN Diodes
-
The SemiGen SBL 2000 series Beam Lead PIN Diodes feature fast switching speeds at both low capacitance and resistance. Beam Lead PIN Diodes have high levels of mechanical strength and stability during assembly. These diodes are suitable for microstrip or stripline circuits as well as circuits requiring high isolation from a series of mounted diodes such as multi-throw switches, phase shifters, attenuators and modulators.
-
Product
Embedded Components
-
Teledyne Labtech prides itself in being at the forefront of RF/Microwave PCB development. Teledyne Labtech were also one of the first companies to successfully develop techniques for embedding SMD resistors and capacitors within multilayer structures and the embedding of connector pins in buried stripline circuits.The advantages of such a structures ensures a much higher density of interconnect. This then removes the need for via-hole connections to the board surface or the need to create access pockets to the inner layers. Consequently you finish with a board with that exhibits much lower RF/Microwave losses. This is particularly important when designing large RF feed networks or 16:1 power dividers.
-
Product
Striplines / TEM-Cells
-
Open, unsymmetrical 50 Ω stripline for automotive immunity testing of components.
-
Product
VME J1 4 Slot with ADC Connectors
101VMEJ104-0590
-
VME J1 backplane 4 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1J2 Monolithic 16 slot
101VMEM116-0500
-
VME J1J2 Monolithic backplane 16 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1J2 Monolithic 18 slot
101VMEM118-0500R
-
VME J1J2 Monolithic backplane 18 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1 12 Slot with ADC Connectors
101VMEJ112-0590
-
VME J1 backplane 12 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1J2 Monolithic 3 slot
101VMEM103-0500R
-
VME J1J2 Monolithic backplane 3 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
90 Degree Hybrid Couplers To 26.5 GHz
-
Pulsar Microwave manufactures hybrid couplers and dividers from 400 MHz to 26.5 GHz for use in 50-ohm systems. These hybrids are available in narrowband and wideband designs with up to 20:1 bandwidth ratios. Most models are built to handle 100 watts input power. The designs are stripline, and optimized for best matching and isolation performance. Available with SMA or N type female connectors.
-
Product
Strip-Line™ Socket with Bifurcated Contact Wire Wrap Pins
Series 0501
-
Strip-line Sockets with Bifurcated Contact Wire Wrap Pins. Features: For mounting liquid crystal displays and other high pin count or odd centered components. Available in several sizes with bifurcated contacts in wire wrap or solder tail pins. Consult Data Sheet No. 12008 for solder tail pins.
-
Product
VME J1J2 Monolithic 14 slot
101VMEM114-0500
-
VME J1J2 Monolithic backplane 14 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
VME J1J2 Monolithic 12 slot
101VMEM112-0500R
-
VME J1J2 Monolithic backplane 12 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
Product
Automotive EMC Testing
-
Having been assessed by Ford Detroit’s EMC expert, we are Australia’s only Ford (and NATA) accredited automotive EMC test laboratory. Others have tried, but none have succeeded. Ford does not accept reports from EMC labs that are not on the Ford list of accredited labs. The scope ranges from component to complete vehicle level EMC testing for Australian and overseas manufacturers. We also have a fully dedicated CISPR 25 Electronic Sub Assembly (ESA) chamber, another large CISPR 25 anechoic chamber for vehicle testing or susceptibility levels in excess of 500V/m. We possess a vast array of specific automotive EMC test equipment such as BCI’s, tri-plate’s, and striplines for susceptibility and emissions testing to meet the most stringent automotive EMC requirements. Our Australian and overseas customers use our labs because they know that our reports will be accepted and will not be questioned.
