LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
5KVA to 100KVA Industrial UPS (3Ø – 1Ø)
NSP Series 5KVA to 100KVA
-
- Designed for powering critical Industrial and IT systems- DSP controlled IGBT based PWM technology- Design topology enables N+1 parallel redundancy- Industrial grade high speed CAN bus communication- User Friendly Matrix LCD and LED mimic front control and digital monitoring- Fully rated make before break maintenance bypass operation- Optional break-less load transfer via static switch- Low harmonic distortion- High crest factor tolerance and dynamic stability- Lower TCO- Continuous full rated power at ambient as high as 45°C- N+1 Parallel operation of UPS without any common hardware- Advanced Communication Capability (RS485/Modbus/SNMP)- High branch fuse clearing capacity- On-line battery bank test without load disconnection- Compact, elegant, and light weight enclosure- Easy installation with wheels for maneuverability and front bottom terminals
-
Product
SparkFun Opto-isolator Breakout
-
This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two photodiodes built-in. This allows the low-voltage side to control a high voltage side.
-
Product
4-CH Lighting Control Module
AX92353
-
*4-CH independent constant current LED drivers (up to 1 A)*Supports strobe and trigger mode*Intensity control by software*Supports duration and delay time for LED output
-
Product
Gas Leak Detector
GSD600
-
The Amprobe GSD600 Gas Leak Detector is a fast responding gas leak detector for methane and propane gas. The meter emits a frequency tone when gas is detected. The frequency of the beep coincides with the concentration of the gas. The LEDs display the level of gas present in an area or room. Pinpoint gas leaks for closed piping systems. Use the mute function in quiet work areas and utilize the LED displays. Or a standard earphone jack for hearing the meter in loud environments.
-
Product
UltraZed PCIe Carrier Card for UltraZed-EG System-on-Module
AES-ZU-PCIECC-G
-
The UltraZed PCIe Carrier Card supports the UltraZed-EG System-on-Module (SOM), providing easy access to the full 180 user I/O, 26 PS MIO, and 4 PS GTR transceivers available from the UltraZed-EG SOM via three Micro Headers. Two 140-pin Micro Headers on the carrier card mate with the UltraZed-EG SOM, connecting 180 of the UltraZed-EG Programmable Logic (PL) I/O to 2 Digilent Pmod™ compatible interfaces, FMC LPC slot, LVDS Touch Panel interface, push button switches, DIP switches, LEDs, Xilinx SYSMON, and clock oscillator.
-
Product
LED Display for SysMon
060-013
-
LED Display accessory for System Monitor (SysMon) with 11 LEDs and push button to generate a SYSRESET# signal directly from the front of the system.
-
Product
18.5" 1366 X 768, VGA/DVI/HDMI Interface, Ultra Slim Touch Open Frame Monitor
IDS-3118W
-
18.5" 1366x768 HD LCD panel with LED backlight for 20% power saving and environmental protection. 0° ~ 55° C wide range operating temperature, 5-wire resistive and P-cap touchscreen solution, Touch interface: USB & RS-232.
-
Product
RCD/LOOP/PAT Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
Custom microprocessor controlled for highest accuracy and reliability. 3 LEDs for checking correct wiring status. 0 and 180 degree phase angle switch permits quick tests and consistent readings. Digital read-out of tripping time. Constant current source circuitry ensures that a fluctuating mains voltage does not affect the accuracy of readings. Large custom digital display readout. Visual indication of reversed phase and neutral wiring at socket. Designed to IP54 Rating. Complies with IEC 61557 Test of a large kind of RCD''''s: Standard, Selective, AC and A (DC sensitive breakers)
-
Product
200 KHz LCR Meter w/RS-232 Interface
LCR 200
-
Measurement Parameters : Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and £c. Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz Basic Accuracy 0.1% ; Test Voltage: 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only). DMM Functionalities. Dual LCD Display with LED backlit
-
Product
Relay Buddy PRO Test Kit
191
-
Relay Buddy is a quick go / no-go tester for the most common automotive relays. With the included adapters, Relay Buddy now tests 5 different relay types and also tests shielded relays. Relay Buddy provides you with an indication of the general health and functioning of the relay switch contacts and coil. It will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
Product
For PWS-872 And PWS-872FL
PWS Series Multi-bay Battery Charger
-
Supports up to 4 external batteriesCharging time: 4 hrCharge status LED indicatorsScrew holes for secure installationPower input: 19.5V/7.7ADimensions: 214.4 x 229.4 x 60 mm (8.44 x 9.03 x 2.36 in)Weight: 1.4 kg (3.08 lb)Packing material: XAASC-FSP150-RFBN2 (1 x 150w adapter)
-
Product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-02
-
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
Product
LED Driver Automatic Test System
ATE-2
-
•This system includes 2 groups (left and right); the 2 groups can work in turn, so that to improve the work efficiency. For example, if the left is on working, then the right can make wire connection. •It can test 4 LED drivers input and output at one time. •The equipment can connect with electronic load and LED load, the two difference loads can be fast switch under the control of computer. •Enable to print out the series number and parameters of sub-quality products by working with a micro-printer, •Enable to achieve the bar-code record function by working with a bar-code scanner. •The test report can be saved as Excel file for consult, statistic and analysis purpose. •Good software interface to freely choose the difference parameters combination, so that to meet different demands. All the parameters can set limit, and with the quality analysis function.
-
Product
4 Digit Angle Position Indicator (API)
TA-900
-
This has been the New standard in Angle Position Indicators. 4 digit API has fault monitoring for both low-level and loss of signal (LOS) and this status is shown on the front panel led. The unit provides simultaneous connection of both synchro and resolver devices.
-
Product
Network Cable Tester
PA-40
-
The PA-40 is designed to check both shielded and unshielded twisted pair (STP/UTP) and coaxial BNC-type network cables. With the push of a button, it tests all wires for continuity, miswiring, and polarization. Dual-colored LEDs let you identify correct and reversed pairs; using the included remote unit, cables may be tested before installation or after installation. Features tip/ring polarity test. Uses 1 9V battery.
-
Product
Handheld Water Quality Meters
LAQUA WQ-310-K
-
- Single channel- Large colour graphic LCD screen (70 x 52 mm) with backlight - Built-in foldable meter stand- IP67 waterproof and dustproof- Battery and USB powered- Eco-friendly, shock-proof, scratch-resistant, and non-slip- Built-in sensor holders- Efficient sensor locking mechanism- Sensor's LED light as reading stability indicator- No sensor adapter needed for attaching multiple sensors together- Compatible with conventional electrodes having BNC and phono connectors and long cables- Sensor status indicator- Temperature sensor indicator- °C & °F temperature units- Sample ID setting- Detailed calibration data- Auto stable, Auto hold, and Real time measurement modes- Customizable meter kit - up to 5 meter-sensor kit combinations- Hands-free testing- Ergonomic design- Multi-language options- Versatile channel and adaptive display- Automatic sensor recognition function- Data transfer via USB or wireless communication- Printer communication- 3 years meter warranty
-
Product
15.6" Full HD Standalone Multi-Touch Panel Computer
SPC-815 V2
-
15.6" FHD TFT LED LCD displayIntel® Core™ i3-1315URE / i5-1345URE processor16:9 widescreen with P-CAP multi-touch controlEnhanced touch screen for impact resistanceSilicone-free enclosure with all-round IP65-rated protectionSupports CP 40 (Rittal) and CS-480 B.Flex (Bernstein) mount standards
-
Product
10 GSPS, 14-Bit Digitizer
ADQ7DC
-
With 14 bits and 10 GSPS, ADQ7DC improves the resolution in high-sampling rate applications beyond what was previously possible. This performance-boost has effectively helped our customers overcome performance trade-offs and have led to significant advances in many applications. ADQ7DC can be operated in either single- or dual-channel mode with 10 or 5 GSPS sampling rate respectively.
-
Product
Bench Top Ionizer Cleaning Box
EC-B
-
Panasonic Industrial Devices Sales Company of America
The EC-B Bench Top Ionizer allows direct ion emission to be paired with pulsed air emission to provide quick and effective removal of static charges as well as any dust that is present on the part. Three white LEDs illuminate the work piece to ensure complete dust removal. A powerful dust collecting fan exhausts dust quickly, preventing re-adhesion of dust.
-
Product
S2 Unicolor Sensors
ULP-S2 SCI/V
-
The Universal LightProbe S2 Unicolor Sensor is designed for the intensity test of any single one of the five main LED colors (blue, green, yellow, orange, and red) plus white and Infrared (700nm to 1,000nm). Implemented in a unique and customizable 2-Part solution, the S2 Unicolor Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times:<10mS capture time; 65mS overall response time; intensity output of correct color only.Fiber-Optic Probes: Can utilize any Universal LightProbe Fiber-Optic Probe
-
Product
15" (4:3) Modular Front Display Design Compatible With TPC-B610, TPC-B520, TPC-B300 Models
FPM-D15T-CE
-
300 cd/m² luminance with 1024 x 768 resolutionHigh durability and performance with industrial-Grade LED LCDAdvanced projected capacitive (P-CAP) technologyIP66-rated front panel and panel mount supportUser-friendly system status LED indicators
-
Product
Compact Inspection Camera
-
Fits in your pocket or clips on your beltAffordable1 meter drop-proofLong, thin camera-tipped probe with excellent depth of field penetrates tight, hard-to-reach spacesProbe is waterproof, holds its configured shape, and coils inside clamshell case for storageFour camera-lighting LEDs produce bright, crisp video on large color LCDFour screen controlsFour useful probe tip accessories (pickup hook, magnetic pickup, 45 mirror, thread protector)
-
Product
Digital Panel Meter
CSN-VA
-
CSN-VA is an economic &simple indicator,large LED display 20.0mm height,anti-jamming design, reliable quality and easy installation.Multiple range of input models, you can specify AC or DC voltage / current ,frequency, 4 ~ 20mA, 0 ~ 10V and pulse signals for all general measurement requirements.
-
Product
Endoscopes and Cameras
-
PeakTech Prüf- und Messtechnik GmbH
Is used to locate objects such as connection terminals, electronic components, break points, constrictions, cracks or components at hard-to-reach, hidden locations. This video endoscope camera offers a variety of excellent technical properties, such as the detachable monitor connected by video cable or the high-resolution camera with 6 dimmable LEDs for lighting, which can take photos and videos.
-
Product
12-42V LED Heavy Duty Circuit Tester
1651A
-
Peaceful Thriving Enterprise Co Ltd
*Check on 12 - 42V systems. *Automatic voltage identification: BLUE LED for General car / RED LED for Hybrid car.
-
Product
Digital Pressure Gauges & Displays
-
Our comprehensive range of hydraulic pressure testing equipment is of the highest quality and makes hydraulic testing much easier and extremely accurate. 75mm digital pressure gauges with 0.5% accuracy up to 600 bar. Numerical & 0-100% bar graph display. Min/max storage. 2 x AA batteries. Stylish pressure switch / gauge up to 700 bar with two settable switch values. 4-20mA output. 15...30Vdc external power required. LED high speed panel mounting displays for frequency or analogue signals.
-
Product
64 Channel 12C GPIO Expansion
FXA-102 I2C Expander
-
The FXA-102 provides 64bit of General-Purpose Input / Output (GPIO) which are controlled via I2C. It is 3,3V and 5V compatible and based on four 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. Using the optional Phoenix Contact UMK housing, the FXA-102 can be installed on a DIN rail. The dual row 2,54mm pin headers allow usage with IDC20 connectors or wire wrap cables.
-
Product
Incoherent Sources
-
Our Incoherent Sources include unmounted LEDs, mounted LEDs, collimated LEDs, LED light sources, superluminescent diodes, and broadband light sources. Our collimated LEDs are particularly popular and are compatible with many microscopes. Versions are available with center wavelengths from the UV into the NIR or that emit white light.
