Fibre Channel
Data transfer interface with speeds up to 2 Gigabit per second that maps to common transport protocols, i.e. IP and SCSI.
-
product
2 To 18 GHz 6 Channel Downconverter
Teledyne RF & Micrrowave's Six Channel 2 - 18 GHz (RF and LO) downconverter operates with an IF of ~960 MHz, providing 25 dB of RF-IF gain, and bandwidth of ~500 MHz. This downconverter operates on a single LO at -6 dBm which is amplified, split, then again amplified to each of the 6 channels. Integrated into each channel is a range extension switch, controlled by a TTL input and adding 20 dB attenuation. Noise figure is ~ 13.5 dB and output IP3 is ~+25 dBm. The downconverter is 2- sided, hermetically sealed and designed for rugged applications.
-
product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, DIO (2-in/2-out), 4 AI Channels (16-bit, 250 KS/s, 0 - 20mA, ±20mA) And 2 PCIe Mini Card Slots
IRU152-I
*RISC-based (i.MX 6UltraLite) processor 528 MHz*512MB DDR3 SDRAM onboard*8GB eMMC flash onboard*2 PCI Express Mini Card slots (Wi-Fi, 3G/4G or LoRa)*4 isolated analog input channels (16-bit, 250 kS/s, 0 - *20mA, ±20mA)*1 isolated COM port*1 isolated DIO (2-in/2-out)*Embedded Linux operating system (Yocto)*Wide operating temperature range from -40°C to +70°C*Supports LabVIEW versions later than 2016*Supports OPC UA
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
Oscilloscope, 50 GHz, 320 GS/s, 8000 Mpts/ch, 4 Channel, 12-bits
WaveMaster 8500HD
50 GHz, 12 bits, 320 GS/s, 400 Mpts/Ch High Definition Oscilloscope.
-
product
Dual Channel High Voltage Linear Amplifier
A800D
This unit contains two independent A800 amplifiers that share common ground reference and power supply.
-
product
Oscilloscope 59 GHz, 2 Channels, 1 mm Inputs
UXR0592BP
The UXR0592BP is the 59 GHz, 2 channel, 1mm input, Infiniium UXR-Series real-time oscilloscope.
-
product
Digital Oscilloscope, 2 Channel, 50 MHz, 1 GSPS, 25 kpts, 7 ns
72-8705A
The 72-8705A from Tenma is a digital storage oscilloscope with 50MHz bandwidth, 2 analogue channels. The digital storage oscilloscope provides trigger modes edge, pulse, and alternate.
-
product
Mixed Signal Oscilloscope, 500 MHz, 4 Analog Plus 16 Digital Channels
MSOX3054A
500 MHz4 analog plus 16 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
product
HandyScope HS6-DIFF With SafeGround & SureConnect: 500 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-500XMSG-W5
The only oscilloscope in the world that has:- SafeGround, differential input channels that can be switched to single ended.-SureConnect, auto-detects a true connection between the probe tip and the device under test.- CMI interface.- USB 3.0 interface, 5Gb/s data transfer- Lowest noise
-
product
Infiniium EXR-Series Oscilloscope: 2.5 GHz, 8 Channels
EXR258A
2.5 GHz on all 8 channels, 8 instruments integrated in one, hardware accelerated plotting, and fully upgradeable
-
product
PCIe 16 Bit Arbitrary Waveform Generator - up to 625 MS/s on 2 Channels
M4I.6621-X8
The M4i.66xx-x8 series arbitrary waveform generators (AWG) deliver the highest performance in both speed and resolution. The series includes PCIe cards with either one, two or four synchronous channels. The large onboard memory can be segmented to replay different waveform sequences. The AWG features a PCI Express x8 Gen 2 interface that offers outstanding data streaming performance. The interface and Spectrum’s optimized drivers enable data transfer rates in excess of 2.8 GB/s so that signals can continuously replayed at a high output rate. While the cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum waveform generators. So, existing customers can use the same software they developed for a 10 year old 20 MS/s AWG card and for an M4i series 625 MS/s AWG.
-
product
Data Analyzer, 16 GHz Bandwidth, 4 Input Channels, 80 GS/s Max Sample Rate
SDA 816Zi-B
16 GHz, 80 GS/s, 128 Mpts/Ch Serial Data Analyzer with 15.3" WXGA Color Display. 50 ohm and 1 Mohm Input, 6.5 Gb/s Serial Trigger, 8b/10b and 64b/66b decode. Also operates in 4ch, 40 GS/s, 64 Mpts/Ch mode.
-
product
PXI RTD Simulator Module, 4 Channel, PT100
40-263-501
The 40-263-501 is a 4-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
200MHZ, 2.4 GSa/S, 20 Mpts, 2 Channel, 20 Vpp Function/Arbitrary Waveform Generator
T3AFG200
Teledyne Test Tools T3AFG5 and T3AFG10 series Function/Arbitrary Waveform Generators are a new family of low cost, high performance, single channel Function / Arbitrary waveform generators offering a high level of functionality and an excellent specification at a very competitive price point.
-
product
WaveRunner Oscilloscope, 500 MHz Bandwidth, 4 Input Channels, 20 GS/s on 2 Ch Sample Rate
WaveRunner 9054
500 MHz, 20 GS/s, 4ch, 16 Mpts/Ch DSO with 15.4" Capacitive Display.
-
product
PXI RTD Simulator Module, 12 Channel, PT100
40-263-301
The 40-263-301 is a 12-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
product
Mixed Signal Oscilloscope: 70 MHz, 4 Analog Plus 8 Digital Channels
MSOX2004A
70 MHz4 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
product
Mixed Signal Oscilloscope 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX3104G
The MSOX3104G 1 GHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
product
NI-9232, 3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module
782000-02
3-Channel, 102.4 kS/s/channel, ±30 V, C Series Sound and Vibration Input Module - The NI‑9232 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The NI‑9232 is also compatible with smart TEDS sensors. The NI‑9232 incorporates software-selectable AC/DC coupling, IEPE open/short detection, and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti-aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking.
-
product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
product
HD Oscilloscope, 2GHz, 10 GS/s ESR, 4 CH, 500 Mpts/Ch (Single Channel), 12-Bit HD
T3DSO4204L-HD
2GHz, 10 GS/s ESR, 4 CH, 500 Mpts/Ch (Single Channel), 12-Bit HD Low Profile Oscilloscope.
-
product
4, 8, 16 And 32 Channels ARINC429 Test & Simulation Module CompactPCI/PXI (3U)
ACXX429-3U-x
The ACXX429-3U-x is a functional replacement formodel ACX429-3U-x.
-
product
HandyScope HS4 DIFF: 50 MS/s 100MHz BW, 4 Channel, USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS4-50-DIFF
* record length is 131060 samples * 128K samples on screen without loss of information * free settable pre trigger position, from 0 to 100% * easy time axis zoom using unique scaleable sroll bar slider * free adjustable sample frequency * vertical offset and gain adjustable with graphical shiftable and scaleable axis * WYSIWYG trigger level, slope and hysteresis adjustment using combined trigger control * Auto setup to reduce setting time with unknown signals * linear/quadratical interpolation * extended cursor measurements * all settings accessable through popup menus * storing and recalling reference signals * software math channel available * easy to use speedbutton toolbar for easy access of all functions * comment tags to mark specific events in the signal * color hardcopy supported * explanatory comments with all controls * envelope mode * averaging of signals
-
product
Eight and Four Channel Quadrature Encoder Input Cards
mPCIe-QUAD
The mPCIe-QUAD-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to two DB-37F Modules via included 9” cables. The mPCIe-QUAD-4 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to one DB-37F Module via an included 9” cable. The modules are designed to be easily panel-mounted in any application environment, and have convenient mounting holes for non-panel-mount applications. Up to eight differential (or single-ended) encoders (each with A, B, and Index) can be monitored simultaneously.
-
product
Oscilloscope 70 GHz, 2 Channels
UXR0702B
The UXR0702B is the 70 GHz, two-channel Infiniium UXR-Series real-time oscilloscope.
-
product
DC Coupled, 14-Bit Digitizer For ExpressCard 54, 2 Channels 150 MS/s
EC14150D
The EC14150D (EC) is an DC-coupled dual channel waveform capture board that provides a remarkable combination of high speed and high resolution sampling along with a very large memory capacity all in a very compact and low power consuming ExpressCard form factor. At 4.5 W, the EC represents one of the lowest power consuming digitizer cards ever created for its class. Signal frequencies up to 200 MHz can be accurately captured either in baseband or in higher order Nyquist zones using under-sampling techniques. Where DC-coupling is required, the EC14150D should be considered.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-Purpose Digitizer - 125 MS/s on 12 Channels, 80 MS/s on 24 Channels, 24 Single-Ended Inputs, 12 True Differential Inputs
DN6.596-24
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
4 Channels of Strain Gauge Inputs for the SCS-800 Signal Conditioning System
SCS-817
The SCS-816 and SCS-817 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-816) and 0.5Hz to 60kHz(SCS-817). Each of the SCS-816/SCS-817's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Digitizer with two 125 MS/s, 14-Bit Channels, Recommended for VXI Systems
6084-2105
The Astronics 6084-2105 digitizer includes two 125MS/s, 14-bit digitizer channels and is recommended for VXI systems that need either improved accuracy or replacement of an obsolete instrument. Wide dynamic sampling, a powerful acquisition engine, and excellent AC/DC performance ensure an upgrade for your VXI system that will preserve your legacy investment for years to come.Key features include:Dual 14-bit digitizers for SE or DIFF operation at sample rates up to 125 MS/sDC accuracy of 0.15% ± 800 µV on low voltage rangesSFDR 80 dB at 1 MHz Wide input ranges from 0.25 Vpk to 256 VpkPerformance upgrade or replacement for existing VXI applications Pre- and post-triggering availableWaveform storage of 32 M samples per channel
-
product
Infiniium S-Series High-Definition Oscilloscope: 8 GHz, 4 Analog Channels
DSOS804A
8 GHz bandwidth4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.4 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
