RF Box
A space surrounded by an electromagnetic radiation barrier
See Also: Boxes, Decade Box, Anechoic Boxes, Black Box, Breakout Boxes, Hot Box, White Box, Shielded Box, Programmable Resistance Box
-
Product
RF Sensor for Spectrum Monitoring
N6841A
-
Reduce operating costs with affordable spectrum monitoring and TDOA geolocation measurementsDeploy fully capable RF monitoring stations faster with simple hardware and measurement-specific software24/7 real-time remote spectrum monitoring with Signal Surveyor 4D softwareCapture intermittent signals with spectrum analysis softwareFaster search and signal isolation with broad attenuation and wide dynamic rangeLocate narrow or wideband signals with geolocation software
-
Product
75 Ohm SMZ/Type 43 Cable Assembly
40-977-711-1m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
MS-M 26-Pin RF Cable Assembly 0.5m
40-979-526-0.5m-FU
-
The MS-M RF 26-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
LXI 75 RF Matrix - 1GHz
-
Pickering's 75 LXI RF matrix - 1GHz range is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of these matrices provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance.
-
Product
RF Proximity Detector
Type RPD-2 AND Type RPD-2A
-
The Type RPD-2 Radio Frequency (RF) Proximity Detector is designed to detect and locate devices that radiate radio waves in the high frequency to low microwave frequency range. Such devices often include surveillance and “spy” equipment. The Type RPD-2, when used with the different sensors, will detect the emanation of the radio wave within a confined area, and then isolate its location to within approximately a square foot. The type RPD-2A may be used as an RF field strength indicator for antenna field strength measurements. The RPD-2A is identical in function except that the meter scale is calibrated in relative dB units.
-
Product
Fifo Serial Analyzer 2 TO 2 Breakout Box
FLL222
-
The FLL222 Break Out Box is designed to be used with the FLL and FSA serial analyzers to monitor full duplex bidirectional data. The serial line passes through FLL222 using the 9-pin connectors on the unit. Data from pin 2 of the serial line is available on pin 2 in the first output cable. Pin 3 data is available on pin 2 of the second cable. The output cables can be plugged into the COM ports of the PC running the serial analyzer.
-
Product
OTDR Launch Cable Box, OTDR Dead Zone Eliminator 100-500M
-
Shanghai Fibretool Technology Co.,Ltd.
Designed to aid in the testing of fiber optic cable when using an OTDR. TheOTDR Launch Cable Box is used with Optical Time Domain Reflectometers (OTDRs) to help minimize the effects of the OTDRs launch pulse on measurement uncertainty. Available in many different configurations and fiber lengths.
-
Product
RF Taps
-
Praxsym’s RF Taps afford access to a cable system for monitoring function and performance without interrupting service. The taps also cause minimal insertion loss when the coupled port is open, as in normal system operation. Like all Praxsym products, these high-quality devices have honest specifications, and are well-documented over the bands they are designed for.
-
Product
RF Testing & Engineering Services
RF Testing & Engineering Services
-
Our team has world-class radio frequency experience in defense contracting, design, engineering, manufacturing, quality, research, and testing. The staff at 360°RF includes numerous design patent holders, a sitting member of the CEA's (Consumer Electronics Assoc.) Standards Committee, as well as columnists, editors, and authors for trade publications and reference books, including Radio Shack, Antennas, Selection, Installation, and Projects, TV, FM, CB, Cellular, Satellite, and Shortwave.
-
Product
Small-Size Modular Embedded Box PC With Intel® Celeron® J6412
UNO-2372G V2
-
Intel® Celeron® J6412 quad-core processor with 8GB DDR4 memoryCompact, robust, fanless and scalable system with high stabilityOptional second stack for supporting extension iDoor module, including wireless connectivity, industrial fieldbus and more I/O portsSupports NVME storage with high data-transmission efficiencySupports Windows 11 IoT Enterprise LTSC
-
Product
RF Test Benches
-
FIME laboratory equipment qualified for RF testingValidate the analogue behaviour of RF devices with a single set of laboratory tools and services before seeking contactless Level 1 type approval or launching mass production. FIME RF test benches are built for RF testing of: EMV contactless cards and readers; ICAO e-passports and readers; ISO devices (PICC and PCD), HF and UHF RFID tags and readers.
-
Product
RF Loads
-
Bird manufactures a broad spectrum of devices from one watt to eighty kilowatts. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators and RF loads.
-
Product
EOL RF Functional Test
AS652
-
With this RF test platform, integrable according to the specific needs of the product, we cover a very wide range of test needs with manual feeding.Ergonomics have been fully observed in the design, including the option of servo adjustment of the working height according to the operator.
-
Product
CATV / RF Over Fiber
-
Transport RF signals: Cable TV (CATV), L-Band (SMATV), NTSC, DOCSIS, Return Path and other RF signals over 110km over a single fiber.
-
Product
RF Signal Generator
-
AC powered RF signal generator offering lower phase noise and USB control.
-
Product
RF Detectors
-
BroadWave designs and manufactures RF Detectors and other coaxial RF components that are ideally suited for test, verification and system integration. With frequency ranges of DC to 18 GHz, our components offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
Product
RF Milliwatt Meters
Type NDB-2 and NDB-3
-
National RF’s Type NDB-2 and NDB-3 RF Milliwatt Meters are affordable pieces of test equipment for both the RF laboratory and the home experimenter. Both provide a digital reading of RF power in dB reference 1 milliwatt of power into a 50 ohm load (i.e. 0 dBm). The circuitry consists of a low noise logarithmic amplifier that drives a digital A/D converting meter circuit. The lowest power levels that can be read are about –73 dBm (approximately 40 microvolts or .00000003 milliwatts). The maximum power input should not exceed 10 milliwatts (+10 dBm or .010 watts) when inputed without attenuation. An internal attenuator is provided and described in the next section.
-
Product
RF Sensors & Probes
-
A meter specifically designed for CEMFAW(2016) requirements. This hand held meter covers Electric, Magnetic and RF fields and will display levels vs standard limits. Includes data logging and GPS feature with automatic plotting to maps for area survey
-
-
Product
RF & Microwave Signal Generator
SMA100B
-
The R&S®SMA100B RF and microwave signal generator delivers uncompromising maximum performance. It provides the purest output signals while maintaining the highest output power levels with the lowest harmonics, far outpacing the competition. As the world's leading signal generator, it can handle the most demanding module and system T&M tasks in the RF semiconductor, wireless communications, aerospace and defense industries.
-
Product
RF Solutions for Defense & Space
-
Teledyne e2v HiRel's standard screened line of RF and microwave components provides a cost and time effective approach to meet the requirements commonly found in military and space applications.When system performance or program screening requirements call for more than Teledyne e2v HiRel's standard catalog screened parts, we can tailor a solution by taking a standard catalog device, assembling with proven assembly processes and tailoring a custom screening program that can be created by either adding or removing screening options or by generating a program specific sequence.
-
Product
Benchtop RF Signal Generator
-
The Benchtop version of the Lucid series offers up to 4 phase coherent channels in a 2U 19” benchtop box. With a 5” touch display and front panel control buttons the Benchtop platform enables users to program the instrument without the need of an external PC. For synchronized, phase coherent, multi-channel applications such as quantum physics and phased array antennas the Benchtop platform is an ideal, high performance and cost-effective solution.
-
Product
Microwave / RF Synthesizers, Test & Measurement
-
Berkeley Nucleonics Corporation
The 825-M is an agile ultra-low phase noise RF signal source from 8 kHz to 20 GHz RF Synthesizer. It is available in single-channel or multichannel configurations. A single channel 825-M is packaged in a compact enclosure, or can be ordered with a touch-screen display, or a 1U 19" rackmountable version. The multi-channel version (2, 3, or 4 channels) is packaged in a 19” 1U rackmount enclosure.
-
Product
RF Termination
DR9-10000-2425-2475-2892
-
Frequency2400~2500MHz, 10KW, Waveguide, FDP26, water cooled (Flow: 5-8L/min)
-
Product
Digital RF Power &V.S.W.R. Indicator
PowerMaster Series
-
Thank you very much for purchasing the Array Solutions PowerMaster Series RF Power/VSWR Indicator. The PowerMaster represents a breakthrough in features for measurement of the performance of your transmitting system. Microprocessor control insures fast capture time and low power consumption. With the ability to monitor your VSWR and power levels at all times, you will know that your transmitter, RF source, and load, or antenna systems are operating effectively and safely. In addition, the power and VSWR relay alarms can quickly shut down your power amplifier system and alert you to the alarm condition. This places an additional layer of protection in your transmitting system to help preserve expensive tubes and finals. The PowerMaster also features the ability to be monitored and controlled from a PC via the bundled software, and the unique ability to be monitored and controlled over a LAN or from the internet. PowerMaster firmware updates will be made available for download from the Array Solutions website as they becomeavailable. This means that the user can take full advantage of features or enhancements just by installing the firmware update. No need to return the meter to the factory for updates.
-
Product
RF Detectors for Millimeter Wave
-
RF Detectors are essential microwave/millimeter wave products for most Tx (transmit sources). Transmitter output power measurement is the main application. It is essential to know the RF output power because the output power level must not go above values set by FCC regulations.The unit of power is the watt for RF detectors. But, most commonly used in most RF and wireless systems to express power is the terms of dBm or decibels related to 1 mW:View more RF Detector
-
Product
LitePoint RF Test System
J750
-
The option of adding LitePoint instrumentation to the J750 system delivers a cost-effective, complete production test solution covering global wireless connectivity standards.
-
Product
RF Solutions for Space
-
Our proven design and manufacturing processes yield high-performance, radiation-hardened, high-reliability RF devices that are designed to withstand the harsh conditions of space.
-
Product
Box Compression Testing Machine
-
Dongguan Kejian Instrument Co., Ltd.
Containers are subject to compressive forces when stacked and during transportation. It is vital to determine the compression strength of the box in order to make sure that the box will be able to resist the anticipated compressive forces and to determine the load that the box will be able to withstand during transit and storage.
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
