Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +44 (0)161 371 6000
- +44 (0)161 371 6010
- Edge Lane
Manchester, England M43 6BU
United Kingdom of Great Britain and Northern Ireland
-
Product
Drying Time & Permeability
-
When developing a coating process, it is important to know the exact time it takes for the coating to dry or cure. For multicoat paint systems, having knowledge of the drying time enables the operator to know when any subsequent layers can be applied. There are many stages involved in the coating drying time. Once a coating has been applied, it levels off under gravity, and, as the coating begins to cure, a thin dry film appears on the surface. The coating then continues to dry until, finally, it is totally cured.
-
Product
Soluble Salt Profiler
130 SSP
-
The Elcometer 130 Soluble Salt Profiler provides fast and accurate measurement of the level and density of soluble salts - over 4 times faster than other Bresle equivalent methods. The new Elcometer 130 Soluble Salt Profiler allows you to complete a Bresle equivalent test in just over two minutes. The multi-point conductivity sensors enable the Elcometer 130 SSP to accurately display salt concentration, showing exactly where the contamination lies and generating full colour salt density maps in 2D or 3D.
-
Product
ISO Viscosity Dip Cups - Frikmar
2437
-
Thanks to its handle, the Elcometer 2437 ISO Viscosity Dip Cup - Frikmar is very easy to use to perform viscosity checks on site or during the manufacturing process.
-
Product
Concrete Moisture Meter
7410
-
The electrodes transmit parallel low frequency signals, calibrated to give average moisture content by comparing the change in impedance between damp and acceptably dry concrete.Calibrated ready for use on concreteInstant readings on a clear, easy to read scaleFully portable, battery operated and non-destructive
-
Product
Film Application & Test Charts
-
For numerous products, such as paint, ink, varnishes, glue and cosmetics, the reliability of many laboratory tests is directly related to the quality and consistency of the samples. Any measurements made on coatings for the purpose of describing their physical properties (drying time, elasticity, abrasion, gloss, colour, shade, etc.) are made on the basis of uniform and comparable samples with precisely controlled thickness.
-
Product
Concrete Inspection
-
Concrete structures are normally constructed using steel reinforcement and Elcometer offers Concrete Covermeters and Rebar Locators to either measure the depth of concrete over the rebar or simply to detect the rebar under the surface. Half-cell versions of the Covermeter can be used to assess the probability that corrosion is taking place on the rebar. Test Hammers are used to assess the surface hardness of cured concrete and Elcometer offers several moisture meters that can be used to determine if the structure is sufficiently dry for coating.
-
Product
Fineness of Grind Gauges
2020
-
The Elcometer 2020 Fineness of Grind Gauges is used to determine the particle size and fineness of grind of many materials including paints, pigments, inks, coatings, chocolates and other similar products.
-
Product
Conical Mandrel Bend Tester
1510
-
The Elcometer 1510 Conical Mandrel Bend Tester is used to determine the effects of bending on the elasticity, adhesion and elongation properties of cured coatings on sheet metal.
-
Product
Bresle Salt Meter
Elcometer 138
-
Incorporating a flat sensor, the Elcometer 138 Bresle Salt Meter measures the conductivity of a sample, then automatically converts this to show the density of salts, negating the need for the user to do a manual calculation when working in accordance with ISO 8502-6 or ISO 8502-9.
-
Product
Elcometer Dust Tape Roller
145
-
The Dust Tape Roller presses the Elcometer 142 Dust Tape to the surface using a controlled constant force as required by BS EN ISO 8502-3 (BS 7079-B3:1993).
-
Product
Coatings Inspection Division
-
For over seventy years, Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings industry. Whether you are measuring surface profile, surface cleanliness, dry film thickness, porosity, adhesion or gloss; or testing the abrasion, scratch resistance or elasticity of a coating - Elcometer's extensive and versatile range of equipment provides the complete solution to your coatings inspection requirements, whatever and wherever they might be.
-
Product
CoverMaster™ Software
-
Elcometer's CoverMaster™ software will manage your data efficiently and effectively. Data is transferred quickly into the CoverMaster™ software data management system via RS232 connection. Both Covermeter and half-cell readings can be stored together with associated photographs, Word documents, Excel spreadsheets and other files.
-
Product
Concrete Test Hammers
-
Test hammers are used to determine the surface hardness of concrete and are one of the most widely used instruments to assess concrete compressive strength. It is the quickest, simplest and least expensive method to obtain an estimate of the quality and strength of the concrete. Test Hammers with both analogue and digital displays are available.
-
Product
Surface Profile Gauge
123
-
The Elcometer 123 Surface Profile Gauge is an easy to use analogue gauge which measures the peak-to-valley height of a blast cleaned surface in a similar way to the Elcometer 224 Digital Surface Profile Gauge.
-
Product
Half-Cell Meter
331HM
-
These easy to use Elcometer 331 Half-Cell Meters measure the condition and potential corrosion of rebars and steel structures within concrete.
