Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +1 248 650 0500
- +1 248 650 0501
- sales@elcometer.com
- 6900 MIller Drive
Warren, Michigan 48092
United States of America
Categories
-
product
AFNOR Viscosity Dip Cups - Frikmar
2436
Thanks to its handle, the Elcometer Frikmar Viscosity Dip Cup is very easy to use to perform viscosity checks on site or during the manufacturing process.
-
product
Abrasion and Washability Tester
1720
The Elcometer 1720 Abrasion and Washability Tester is robust, reliable and extremely versatile and is designed for testing the washability, brushability and resistance of a wide range of materials.
-
product
Mechanical Coating Thickness Gauges
Mechanical Coating Thickness Gauges are suitable for working in high risk areas such as high temperature or flammable atmospheres, underwater or where the risk of explosion is high and could be triggered by the use of an electronic instrument. From the simplest coating thickness gauge Elcometer 101 which will provide you with quick and immediate results to the more accurate coating thickness gauge Elcometer 211, also called the "banana gauge" which is ideal for cold and underwater surfaces.
-
product
Anemometer
410
Rugged and durable: the Elcometer Anemometer is made from high impact injection moulded plastic and corrosion resistant materials.Waterproof: Waterproof equivalent to IP67 with fully sealed electronics. Will also floatin water if dropped.Clear LCD Display: Easy to read, large 9mm digits.Choice of measurement units:Beaufort ForceKnotsKilometres per hourMetres per secondMiles per hourFeet per minute
-
product
Surface Contamination Kit
138/2
The Elcometer 138/2 Surface Contamination Kit provides the user with a means for testing invisible surface contaminants including:pHchloride ionsironsalts
-
product
Digital Pocket Thermometer
212
The probe conveniently folds back into the side of the instrument, preventing damage when not in use.Liquid or surface probe options availableUser switchable between °C and °FResolution can be set to 0.1°C (0.1°F) or 1°C (1°F)
-
product
Moisture Measurement
Moisture: The presence of moisture within a material will result in poor adhesion, premature coating failure and poor appearance. For example, applying a powder coating to a damp wooden panel will cause steam to be created when the panel passes through the curing oven, thus causing damage to the coating. It is not sufficient to simply ensure that the surface is dry by touch. The surface of the substrate is often the driest point due to evaporation. It is important to establish the moisture content within the substrate itself. The moisture measurement can either be taken using a Pin moisture meter or Pinless (Contact-Type) moisture meter.
-
product
Chloride Ion Test Kit for Water
134W
The Elcometer 134W is used to monitor recycled water (after it has been applied) to establish effectiveness of salt removal, this test is ideal for testing the salt contamination in wash water and blast water.
-
product
Zahn Viscosity Dip Cups
2210
The Elcometer 2210 Zahn Dip Cup is a small U-shaped viscosity cup suspended from a looped wire.
-
product
ISO Viscosity Flow Cups
2353
The Elcometer 2353 ISO Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
product
Surface Profile
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
product
Chloride, Sulphate & Nitrate Kit
134 CSN
Supplied in an ABS plastic carry case for easy portability around the site, each field kit is supplied with full instructions attached to the inside lid, together with:5 x Chloride tests5 x Sulphate tests, together with 1 x colorimeter, for sulphate testing5 x Nitrate test strips5 x Syringes (without needles)
-
product
Calibration
Formal quality systems, such as those described in ISO 9000, require gauges to be properly controlled, logged and in calibration. Increasingly, users are specifying that the readings taken by gauges are traceable to National Standards. There are three types of coating thickness standards available from Elcometer: calibration foils, coated standards and zero test plates.
-
product
Bresle Salt Meter
Elcometer 138
Incorporating a flat sensor, the Elcometer 138 Bresle Salt Meter measures the conductivity of a sample, then automatically converts this to show the density of salts, negating the need for the user to do a manual calculation when working in accordance with ISO 8502-6 or ISO 8502-9.
-
product
Wet Sponge Pinhole Detection
Wet Sponge Technique: A low voltage is applied to a moist sponge. When the sponge moves over a coating flaw, liquid penetrates to the substrate and completes an electrical circuit, setting off the alarm. The wet sponge technique is suitable for measuring insulating coatings less than 500μm (20mils) on conductive substrates, and is ideal for powder coatings and other coatings where the user does not wish to damage the coating.
