Performance Testing
determines degree of ability.
See Also: Conformance, Qualification, Benchmark, Failure Analysis
-
Product
MultiMeter
TW3204
-
Techwin(China) Industry Co., Ltd
Multi-Meter TW3204 integrates both an optical power meter module and an optical light source module and can perform closed-loop tests by using both modules,and can also work individually. It is specifically designed for technical support personnel to test a variety of instruments with a single meter and thus satisfy the user by providing a choice of greater convenience and more advantages.
-
Product
Memory Test System
T5230
Test System
T5230 memory test system for NAND/NVM devices adopts a combined array architecture to achieve best-in-class cost-of-test performance for wafer test, including wafer-level burn-in (WLBI) and built-in self-test (BIST). The system can perform on-wafer test of 1,024 memory devices per test head in parallel, delivering high productivity and enabling floor space savings of up to 86%. Multiple test cells are connected per system controller in the T5230, allowing independent wafer test of each test cell. The test cells can be stored in a general multi-wafer prober while minimizing the test cell floor space, and the tester can be docked with probers in both linear and multi-stack configurations. For functional tests at a maximum test rate of 125MHz/250Mbps, the T5230 assures high timing accuracy, repeatability, and failure detection capability.
-
Product
Mainframe Performance Monitoring & Analysis
Strobe
-
Compuware Strobe is the industry-leading application performance monitoring and analysis solution for mainframe applications. With Strobe, IT departments can pinpoint application inefficiencies that cause excessive CPU consumption and reduce hardware and software costs while increasing customer satisfaction.
-
Product
Life Cycle Module Testing System
LCN
-
Full featured test system for quality control and R&DLife Cycle Testing: Perform charge/discharge cycling of batteries or modules to obtain charge and discharge capacity, energy and DC internal resistanceAutomotive Battery TestingStarting, Lighting and Ignition (SLI) TestingTraction Battery Testing
-
Product
Automotive Testing
-
Unique E-Marking Service: Efficient, Flexible and Quality Kiwa Dare is a full compliant test house that perform tests and measurements for customers so that the E-Marking (type approval) can be obtained on vehicles or automotive products and components.
-
Product
Circuit Breaker Test System
AutoScan
-
AutoScan Circuit Breaker Test System is used for performing routine tests on circuit breakers and various other types of switchgear. This test system is designed to test vacuum circuit breakers, high voltage circuit breakers, and extra high voltage circuit breakers as per suitable standards.
-
Product
Motor Winding Ohmmeter
RMO-M Series
-
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
-
Product
Tracer Gas Diffuser Kit
DIF-KIT
-
The Kanomax tracer gas diffuser kit is used in performing tracer gas tests in accordance with ANSI / ASHRAE Standard 110. The diffuser is designed to the specifications of standard drawing #110-83M.
-
Product
Battery Checker
SK-8551
-
Total condition check for 12V (24V) batteries. (Truck, Marine, Industry etc.)Battery check, Engine start performance, Charging system tests.
-
Product
Brush Holder Tester
-
Shanghai Aoboor Electric Co., Ltd.
Applicable to electrical performance test of brush holder motors.
-
Product
Multi-Purpose Brake Dynamometers
GIANT 6000 Series
-
The GIANT 6x00 product line is a multi-purpose, full-size inertia brake dynamometer for performance and NVH tests of brake systems from passenger vehicles to truck brakes, commercial vehicle assemblies and high-speed railway applications. The GIANT 6x00 product line offers a complete range of test functions for fully automated performance tests and basic NVH investigations and can be designed to fit the requirements of our customers.
-
Product
FPGA Fast Fourier Transformation (FFT)
eXpert / Fast Fourier Transformation
-
Fourier Transform Analysis is Advanced On-board FPGA Technology a powerful signal-processing technique used in a wide variety of applications. GaGe’s eXpert FFT firmware allows CompuScopehardware to perform Fourier Analysis within its on-board processing FPGA.
-
Product
Optomechatronics Testers
-
T100 is a flying actuator tester designed to calibrate and test any kind of device, module or product with electronic, optical and mechanical functions, using the latest opto, MEMS, sensor, microelectronics, micromechanics technologies.T100 can be equipped with tools and actuators to perform calibration, electrical test, mechanical test, optical test.All on a single machine without any need for additional equipment.It is the ideal tester for production lines with a wide variety of products and frequent entry of new ones.
-
Product
Digital Circuit Breaker Analyzer
CT-8000 S3
-
The CT-8000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-8000 S3 is available with 3 (part number 9103-UC) or 6 contact timing channels (part number 9104-UC). The CT-8000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Also, an outstanding feature of the CT-8000 S3 is the ability to perform dynamic resistance tests on circuit breaker contacts.
-
Product
Adapter/Stainless Steel
WADP-24M29M
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
PoE Tester
PE-100
-
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
Product
Hand‐held Digital Battery Tester w/ Thermo Printer, USB port
12-1015
-
• Tests 12V Flooded, AGM, Gel Cell, Enhanced Flooded (Start/Stop Batteries)• 10 Line LCD display• Performs ground test• Checks diode ripple• Stores last 250 test series with or without power• Carrying case, printing software and USB cables included• Built-in thermal printer with thermal paper (611305)
-
Product
Multi-Layer Analyzers
LTE-Advanced Xpert™
-
The LTE-Advanced Xpert multi-layer analyzer is a unique, real-time continuous protocol analyzer for LTE and LTE-Advanced networks. Installed between a base station and its served mobile devices, the LTE-Advanced Xpert captures the LTE-Uu uplink and downlink transmission and performs deciphering and analysis of data and control channels in real time.
-
Product
Battery Voltage Supervisor
BVS
-
DV Power battery voltage supervisor – BVS, is an accurate battery voltage monitoring system that monitors the state of health of battery systems. It records important battery parameters such as battery voltage, inter-cell connection voltage, and ambient temperature. Because of that, it can be a support tool for capacity testing.The BVS voltage supervisor is an integrated system consisting of:BVS Control Unit (BVS-CU)Cell Voltage Modules (CVM)String Voltage Module (SVM) (optional)String Current Module (SCM) (optional)It is an ideal testing tool for maintenance, troubleshooting and performance tests on individual stationary batteries and battery packs in critical backup energy solutions.BVS-CU provides ambient temperature measurements on multiple locations (4 temperature channels). Overall string voltage and string current monitoring can be achieved by using an optional string voltage module (SVM) and string current module (SCM).There are two types of DV Power battery voltage supervisors:BVS – One cell voltage module measures 1 cellBVS-4 – One cell voltage module measures 4 cellsCVM modules detect cells that fail a discharge test based on monitored voltage values. As a result of that, these cells can be safely removed from the battery string.Data acquisition and analysis of data collected from the modules are available in the DV-B Win application software suite. They provide data viewing, tracking, and generation of comprehensive reports.
-
Product
Portable Gas Analyzers
SERVOFLEX
-
Offering the precision sensing technology of Servomex fixed analyzers in a compact, easy to use package, SERVOFLEX analyzers deliver high performance portable gas analysis for safe or hazardous area use. Utilizing Servomex’s nondepleting Paramagnetic and Infra-Red sensor technology, SERVOFLEX analyzers deliver stable and reliable measurements for oxygen, carbon monoxide and carbon dioxide.
-
Product
PC Edition Ynit
RH-2000
-
"RH-2000" is a digital microscope which can evolve and customize. 2D Measurement, 3D Measurement, and Tilting. "RH-2000" enables you to make a high performance observation and analysis.
-
Product
Portable Electricity Meter Testers
EE-120A-1S
-
The EE-120A-1S unit consists of a single-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types single-phase electricity meters using the voltage of the site. The meter error can be measured for active, reactive or apparent energy, in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the site – with direct measurement or with optional current clamps.
-
Product
Current Booster
BUX
-
The current boosters allow performing tests up to 2000A, 3000A and 5000A. The option is made of a module, which incorporates a power transformer, which generates a low-voltage, high current output and a metering CT, which measures the output current and sends the metering to eKAM.
-
Product
Unclamped Inductive Load Tester
ITC55300C
-
Model ITC55300C performs ruggedness testing of power MOSFETs, discretes and modules and IGBTs, discretes and modules. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
-
Product
Computer-controlled Torque Testing System
Torque Testing System,
-
Our top-of-the-range Vortex-i torque testing system gives optimum testing performance and evaluation options, enabling you to get the most from your test measurements.
-
Product
Thermal Insulation Demonstrator
-
Shenzhen Linshang Technology Co., Ltd.
Linshang Technology offers three sales kits to demonstrate the thermal insulation performance and UV blocking performance of glass and window films, two solar film temperature meters LS300 and LS301 to demonstrate thermal insulation performance through temperature test, two power meter: infrared power meter and UV power meter.
-
Product
500 AMP Carbon Pile Load Tester
710
-
The #710 will perform variable load testing on 12 volt batteries rated as high as 1000 Cold Cranking Amps. Use this battery tester to simulate actual cranking loads. Also tests alternator charging voltage and relative starter current draw. The #710 features large dual meters to display the battery voltage and load current simultaneously, during the test.
-
Product
Battery Discharge Test Unit
125V DC 100A
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
Auto Tensile Tester
ATT-01A
-
Jinan Leading Instruments Co., Ltd.
ATT-01A Auto Tensile Tester is applicable in the test of physical mechanical properties of plastic films, laminated materials, adhesives, adhesive tapes, adhesive bandage (plaster), release paper, protective film, leather, rubber and paper fiber, etc. It can perform the test items of tensile, peeling, deformation, tearing, heat seal, adhesive, open force, etc.
-
Product
General-Purpose Analyzer Systems
-
Brüel & Kjær Sound & Vibration A/S
Sonoscout is a system that uses an app on an iPad to control a wireless data acquisition unit. This rugged front-end can connect up to 12 transducers, such as a binaural headset for in-vehicle recording at the user's ear positions. The front-end is battery-powered and transmits data to the iPad for recording or records directly to SD card inside the front-end, avoiding the need to use Wi-Fi. The intuitive app makes it simple to either perform basic analysis, or to replay and listen to files in order to validate recordings before exporting them for further analysis and archiving in PULSE Reflex.
