Printed Circuit Assembly
Printed Circuit Board Assembly
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male Offset VHDCI
540205020240
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin Male Offset VHDCI
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Ferrules, 2m
40-972-015-2m-MU
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks.The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 20-Pin Power Connector
540145010101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 20-Pin Power Connector
-
Product
Circuit Breaker Timer
-
* Micro - Controller based technology* Very Compact and lightweight* Very accurate measurements* Available with built - in thermal printer or RS 232 interface* Available in bench top and industrial suit case models.* Economical
-
Product
Circuit Tester With Buzzer
28620
-
Tests low voltage up to 28 volts. Spring loaded hook can be removed to use the probe tip only. Can also be used to check polarity and battery drain.
-
Product
20-Pin GMCT Cable, Male to Male, 16A, 0.5m
40-970B-020-0.5m-MM
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Build-to-Print for Test Systems
Test System
Built-to-print / test system replication addresses your internal capacity and capability constraints. Ball Systems has perfected quoting, procurement, planning, assembly, testing, quality, delivery and installation to ensure your testers are on-time and on-budget, and meet design and production standards while keeping open and transparent communication.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 1 Amp, 1m, 500 Port
A500RMR-F-1B100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.
-
Product
Cable Assembly, Receiver, TriPaddle/Coax, 20", 68-PIN Male VHDCI, 4 SMA Plugs, 2 SMB Plugs
540170010143
Cable Assembly
Cable Assembly, Receiver, TriPaddle/Coax, 20", 68-PIN Male VHDCI, 4 SMA Plugs, 2 SMB Plugs.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assy 26-Pin D-Type Male to Female 1m
40-970-026-1m-MF
Cable Assembly
The 26-Pin D-Type cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 26-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 2 Amp, 1m, 250 Port
A500RMR-T-5C100
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin VHDCI
540072020240
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 36", 2 68-Pin VHDCI
-
Product
Cable 100-Pin Micro-D Male to Unterminated, With Ferrules, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-F-9A200
Cable Assembly
This 2m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
Product
Cable Assembly 44-Pin D-Type Male to Male, 1m
40-970-044-1m-MM
Cable Assembly
The 44-Pin D-Type Density and a Half cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Ferrules, 2m
40-972-009-2m-FU
Cable Assembly
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
Product
75 Ohm SMZ/Type 43 Cable Assembly
40-977-711-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Cable Assembly 78-Pin D-Type, Male to Unterminated With Cut Ends, 1m
A078HM5-C-0A100
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Cable Assembly, Twisted Pair, Differential Signals, 78-Pin D-Type Male to Female, 2m
A078DMR-078DFR-9A200
Cable Assembly
The A078DMR-078DFR-9A200 is a 78-Pin Male to Female D-Type Cable Assembly with twisted signal pairs suitable for differential signals and is designed to be used with Pickering's 40-200 fault insertion switch.
-
Product
75 Ohm SMZ/Type 43 Cable Assembly
40-977-711-2m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m
A015DF4-C-0A050
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Open Circuit Locator
A994
-
The A994 is an open circuit locator for electric and telephone cables wind on the reel; it gives the position of the fault from the inside or outside end of the cable, in percentage to the total cable length. The instrument measures the ratio of the capacitances of the two sections of failed conductor using two high precision i/v converters. The advantage of this method is due to the fact that the measurement error depends almost exclusively on the dimensional inhomogeneity of the cable. The A994 has the unique feature to permit the location of fault in cables with all broken wires. This instrument locates breaks in cables with a total capacity between 2 nF and 5 uF. The distance to fault is displayed on a large LCD display.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", RJ45 Plug
540030010140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", RJ45 Plug
-
Product
Cable Assembly, 192-Pin Receiver, QuadraPaddle, 60", 160-Pin Female DIN
540069010940
Cable Assembly
Cable Assembly, 192-Pin Receiver, QuadraPaddle, 60", 160-Pin Female DIN
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Ferrules, 2m
A068SMR-F-5A200
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Cable Assembly, Receiver, TriPaddle, 20" (2) 16-Pin Connectors
540029010101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20" (2) 16-Pin Connectors
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", for NI PXIe-4339
540309010140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", for NI PXIe-4339
-
Product
Cable Assembly, Receiver, 20", Micro Power to 41-Pin FML Power Connector, for VTI EX1200-2001 Switch Module
540249010147
Cable Assembly
CBA, RCV, MicroPWR to 41-Pin J1 PWR Conn f/VTI EX1200-2001 Switch Module.
-
Product
Cable Assemblies
-
We offer a variety of cables covering DC to 110Ghz. Cable assemblies from 0-6Ghz we usually build in our Quick Turn Cable Assembly Shop, delivery is 1-2 days. We also offer some Low Loss Phase Stable from our quick turn shop; but some of the precision cables can take longer.
-
Product
500-Pin SEARAY Cable Assembly (500-Port version), Male to Unterminated with Cut Ends, 1 Amp, 0.5m length
A500RMR-C-1B050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC. This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
