Serial Digital Interfaces
A family of digital video interfaces standardized by SMPTE.
-
product
Interface Adapters and Serial Data Repeaters
Designed to provide a fan-out of up to ten RS-232 compliant outputs from a single input, the SSD120-100N-SDR is an all solid-state Serial Data Repeater. This device provides a simple and robust means of transmitting serial data to multiple aircraft systems in a small package.
-
product
4-CH 16-Bit 10/40 MS/s PCI Digitizers with 512 MB Memory
PCI-9816/9846
The ADLINK PCI-9816/9846 are 10MS/s, 40MS/s sampling 16-bit 4-CH digitizers designed for digitizing high frequency and wide dynamic range signals with an input frequency up to 20 MHz. The analog input range can be programmed via software to ±1 V or ±0.2 V and ±5 V or ±1 V. With a deep onboard acquisition memory up to 512 MB, the PCI-9816/PCI-9846 are not limited by the data transfer rate of the PCI bus to enable the recording of waveforms for extended periods of time.
-
product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels
M4I.4481-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
NI-6584 / 781290-02
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
product
PCIe-6537B, 32-Channel, 50 MHz, 200 MB/s Digital I/O Device
782631-01
32-Channel, 50 MHz, 200 MB/s Digital I/O Device - The PCIe-6537 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
product
sbRIO-9862, Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module
785963-01
Non-Enclosed, 1-Port, High-Speed, Flexible Data Rate C Series CAN Interface Module—The sbRIO‑9862 is a high-speed Controller Area Network (CAN) Flexible Data‑rate (FD) interface for developing applications with the NI‑XNET driver. The sbRIO‑9862 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The sbRIO‑9862 is only compatible with CompactRIO systems. Non-enclosed modules are designed for OEM applications.
-
product
Ethernet Network Interface Cards
Our Ethernet cards, which support copper and fiber, are designed to relieve your bandwidth bottlenecks in compactPCI and VMEbus applications.
-
product
ARINC interface
RAR-EC
Available in a range of configurations to match your needs, the 11 channel RAR-EC provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols, for an ExpressCard interface. The RAR-EC supports maximum data throughput on all channels while providing onboard message scheduling, label filtering, multiple buffering options, time-tagging, error detection and four avionics-level I/O discretes.
-
product
4-CH 16-Bit 80 MS/s PCI Express Digitizer
PCIe-9834
ADLINK's new PCIe-9834 high-speed PCI Express digitizer, featuring four simultaneously sampled 80 MS/s input channels with 16-bit resolution, 40 MHz bandwidth, and up to 1 GB DDR3 onboard memory. Each of the four input channels supports up to 80MS/s sampling, with 16-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no interchannel phase delay. The extremely large onboard memory enables long recording times even at the highest sampling rates. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9834, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card.
-
product
Smart GPIB Serial Interface Board
Model 4806
* Provides GPIB-to-serial and serial-to-serial data paths for serial devices with RS-232 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message. • On board voltage regulator for operation from 5 to 15 Vdc power. • Rear panel mounting eliminates cables.
-
product
Multi-Channel 10-Bit Digitizer
ADQ8-8C
With compact modular form factors, 8 channels per board, and high-precision multi-board synchronization capabilities, ADQ8-8C is ideal for massive multi-channel implementations.
-
product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 12 Channels, 12 Single-Ended Inputs
DN6.448-12
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
1553 to Ethernet Converter
eNet-1553
eNet is a small, rugged 1553 to Ethernet appliance/converter (~200 grams and about the size of a 4 stub coupler) and offers the same advanced BC, mRT and BM functions as our cards. In addition, eNet can provide an additional independent BM mode to auto bridge (transmit) 1553 messages on user defined IP/UDP packet header. The appliance can also auto-load setup images for fast auto start-up, which would be ideal for simple RT applications that wouldn’t even need an API interface (just a standard UDP interface – usually through simple socket programming).
-
product
Digital multimeter, 6 digit
34461A
Color, graphical display with built-in bar chart, histogram, trend, math, and statisticsI/O: USB, LAN/LXI, GPIB (optional)BenchVue software enabled: Do more with your PC and instrument together, no programming required. Easily control your DMM, quickly build automated tests, log measurements and save precious time.
-
product
Interfaces
Channel link cable. Allows two scopes to be linked together to give 4 analog and 16 digital channels. Requires the four channel software to be installed.
-
product
GPIB Serial Interfaces
ICS's GPIB Serial Interfaces provide a mix of RS-232 and RS-422/RS-485 asynchronous signals to drive serial devices. Interfaces are available for transparent data transfer and with smart firmware that adds an IEEE-488.2 Interface to plain serial devices or with embedded PC boards. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
product
PCIe-4065, PCI Express, 6½-Digit, ±300 V Digital Multimeter Device
779771-01
The PCIe‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
product
Interface
RQVME2-1553
The RQVME2-1553 provides new levels of performance and flexibility for MIL-STD-1553A and B Notice II on the VMEbus. Available in commercial, industrial and conductively cooled versions with one, two or four dual-redundant channels, the RQVME2-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
product
PCIe Thunderbolt 3 EON Express 12-Bit Digitizers
Thunderbolt 3
Thunderbolt 3 provides the largest bit-rate capacity interface possible at up to 40 Gbps (5 GB/s) over a USB-C connector to support a variety of protocols including PCI Express (PCIe).
-
product
Serial Device Servers
Advantech''s serial device servers, Modbus gateways, and USB Device Server are easy to install and configure, support wired and wireless networking and provide various operation modes to satisfy rigorous industrial automation needs.
-
product
Interfaces
A computer-video interface ensures computer-video signals can be displayed on large-screen projectors or monitors.
-
product
Digital to Synchro and Digital to Resolver Converters
Computer Conversions Corporation
1.2VA, 1.5VA, 4.5VA and 5VA Models60 or 400, & 60 and 400 Hz. Models to 22 KHz.Trouble Free Isolated Reference Inputs & Signal OutputsUltra High Efficiency, Low DistortionSelf Powered off the AC Reference Input (DSP Series)Internal Cool AC-Pulsating Supplies (DSP Series)Very Low Loss & Heat DissipationFULLY INTEGRATED, NO EXTERNAL COMPONENTS REQUIREDVery High Resistance to Shock and VibrationHigh Reliability Throughout ImplementationIsolated, Transient, Therrnally & Short Circuit Protected Outputs
-
product
Multiprotocol Serial Card
PCIe-ICM-4SM
The PCIe-ICM Series are a new family of isolated PCI Express serial communication cards. These PCI Express cards feature a selection of 4 or 2-ports of isolated, software selectable, RS-232, RS-422, and RS-485 serial protocols.
-
product
PCI 16 Isolated Input Digital Interface (3-13V)
8006
The 8006 PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments.
-
product
cPCI Serial Backplanes
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system's card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
product
PXIe-6545, 200 MHz, 32-Channel PXI Digital Waveform Instrument
780993-03
200 MHz, 32-Channel PXI Digital Waveform Instrument—The PXIe‑6545 is a digital waveform generator and analyzer for interfacing with 32 single-ended digital pins. The device is capable of sampling digital waveforms at up to 200 MHz and interfacing with common transistor‑to‑transistor logic (TTL) voltage levels. The PXI‑6545 also features advanced synchronization capabilities for building integrated mixed-signal test systems and per-bank digital timing features.
-
product
Serial I/O Boards
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
product
NI-6581B, 100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO
783887-01
100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO—The NI-6581B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581B can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
product
PCI Fault Insertion Switch Range for Differential Serial Interfaces
50-200/201
Pickering Interfaces, a leading supplier of modular signal switching for electronic test and simulation, is expanding its range of PCI Fault Insertion switching with the introduction of two new modules (models 50-200 and 50-201) designed for use with differential serial interfaces. PCI Fault Insertion Switch Cards for Differential Serial InterfacesThe new modules include the Differential PCI Fault Insertion Switch (model 50-200) which is designed for lower data rate serial interfaces such as CAN and FlexRay, and the High Bandwidth Differential PCI Fault Insertion Switch (model 50-201) which is designed for higher data rate serial interfaces such as AFDX and 1000BaseT Ethernet. Each module allows the introduction of fault connections that include data paths open, data paths shorted together, and data paths shorted to externally applied faults such as power supplies and ground. The software driver defaults to a protective mode where conflicting faults are prevented to avoid accidentally shorting unintended paths, such as power to ground. A separate mode allows complete freedom in setting fault patterns.
