HiL Simulation
-
Product
VXI 12-Channel, 3-Wire LVDT/RVDT Simulation
65DL2
Simulator
NAI’s 65DL2 is a 12-channel, 3-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board features up to 12 stimulus channels of 3-wire LVDT/RVDT, wraparound self-test, and onboard programmable excitation supply. The board is uniquely versatile, as each excitation input and output voltage is programmable. In addition, each channel can be programmed to be controlled by an external DC voltage. A replacement for the 5410C-83, the 65DL2 is ideally suited for defense, commercial aerospace, and industrial applications.
-
Product
PXI 6-Channel Battery Simulator Module
41-752-001
Simulator
The 41-752 is a 6 channel battery simulator, each channel being capable of supplying up to 7V and 300mA to the load. Each channel is fully isolated from ground and from each other allowing the channels to be connected in series to simulate batteries arranged in a stacked architecture. The 750V isolation barrier permits the 41-752 to be used to create a lower power version of a battery stack representative of those used for vehicle propulsion.
-
Product
GPS Simulator
ADIVIC MP6220
Simulator
Multi-channel GPS simulator for GPS receiver position fix testIndividual channel is power adjustableSingle channel mode for receiver S/N ratio testTunable power output level from -160dBm to -55dBm
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X-FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. By simply upgrading the firmware / software, a single function board can become a full function board without having to purchase new hardware.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel With V/I Readback
41-752A-012
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PCI-8516, 2-Port, PCI, LIN Interface Device
781365-01
LIN Interface
2-Port, PCI, LIN Interface Device—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
PCI RTD Simulator Card 6-Channel PT100
50-262-101
Simulator
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card provides a setting resolution of <8mΩ (also available in <90mΩ - PT1000version) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
Single Stream STANAG3910/EFEX Test And Simulation Module for PCI
APXX3910
Simulator
STANAG3910/EFEX Test and Simulation module for PCI with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APXX3910 is a functional replacementfor model APX3910.
-
Product
PXIe Battery Simulator Module, 4-Channel, 5 Amp
43-754-011
Battery Simulator
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
PXI Millivolt Thermocouple Simulator Module - 16 Channel
41-760-003
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
-
Product
PXI RTD Simulator Module, 20 Channel, PT500
40-263-102
Simulator
The 40-263-102 is a 20-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-913
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 750 V Isolation
43-752A-012
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
41-752A-112
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel
41-752A-003
Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
Battery Simulator
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
PXI RTD Simulator Module 12-Channel PT1000
40-262-202
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
PXI RTD Simulator Module, 12 Channel, PT1000
40-263-303
Simulator
The 40-263-303 is a 12-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI/PXIe Resolver Simulator Module, 2-Banks
43-670-203-AABBCC
Simulator
The 41/43-670-203 is ideal for the simulation of Resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire resolver.
-
Product
Regenerative Grid Simulator
61800 series
Simulator
Market demand for Distributed Resource (DR) products such as PV inverters and wind energy systems is steadily growing as the world strives for clean renewable energy sources. This demand has created a need for rigorous regulation testing to standards such IEEE 1547 / IEC 61000-3-15 / IEC 62116 ensuring proper and safe operation of on-grid products. It has become critical to manufacturers to conduct these tests to prove compliance and to relieve product liability concerns. Chroma’s new 61800 family of Grid Simulators has been designed to fulfill these test requirements by providing a full 4 quadrant, fully regenerative, grid simulator with advanced features for compliance, safety and product verification testing.
-
Product
Single or Multi-channel Coherent Signal Simulator
Z2090B
Simulator
The Z2090B-3xx can generate single or multiple coherent outputs to 44GHz with precise phase and amplitude offsets. It is available as a component bundle or as an integrated system.
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
Simulator
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
41-752A-103
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
2 Port 10/100/1000Mbit/s AFDX/ARINC664P7 Test, Simulator And Monitor Module For PCIe
APE-FDX-2/B
Simulator
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
Product
Solar Array Simulator Auto-Ranging Module 0-160V, 0-10A, 1kW
MP4361A
Simulator
The Keysight MP4361A is a 1000 W solar array simulator DC power module that simulates the output characteristics of a solar array. The MP4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin, etc.).
-
Product
4, 8, 16 And 32 Channels ARINC429 Test & Simulation Module CompactPCI-Express/PXI-Express (3U)
ACE429-3U-x
Simulator
4, 8, 16 and 32 channels ARINC429 Test & Simulation module for CompactPCI-Express/PXI-Express (3U).
-
Product
Synchro/Resolver Simulator, Programmable
5330A
Simulator
NAI's 5330A Synchro/Resolver Simulator is a rack-mount or bench-top instrument featuring integrated touch-screen controls and input terminals. This model represents a major step forward as it uses digital technology to produce Synchro and Resolver outputs. Improved flexibility is provided by two fully independent outputs that can be used to simulate two separate Synchro or Resolver signals simultaneously, or can be combined to operate as two-speed outputs. The versatility of this device has been substantially increased by incorporating dynamic modes that enable servo systems to be tested under various simulated stringent field conditions.
-
Product
Solar Array Simulator DC Module, 130V, 5A, 600W
E4362A
Simulator
The Keysight E4362A is a 600W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4362A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for CPCI With 2 Or 4 CAN Bus Nodes
ACC825-3U-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for CPCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACC825-3U-x CPCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
