Wafer Level
-
Product
Wafer Level Test
-
Double sided wafer inspection system is an automatic inspection system for afterdicing wafer chip. It can do double side inspection simultaneously. The appearance defects of wafer chip are clearly conspicuous by using advanced illumination technology. Illumination and camera acquisition mode can be adjusted for various wafer process, like vertical chip or flip chip.
-
Product
Inspects MEMS and Wafer Level Devices
NorCom 2020-WL
-
The NorCom 2020-WL is specifically designed for wafer-level inspection and leak tests up to 1000 devices per cycle. The system can inspect up to an 8” wafer on or off a saw frame. It is designed to test MEMS and other wafer level devices that have a cavity.
-
Product
Wafer Level Test Handler
Kronos
-
Wafer level test handler for 6/9DOF sensors with real stimulus. Very high UPH capacity and the lowest cost of test (COT). KRONOS is one of the only wafer level test solutions for motion sensors with real stimulus.
-
Product
Wafer-Level Parametric Test
test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
Product
MultiSite Test sockets and Wafer Level
-
multi-site sockets include anything from strip test sockets to test sockets for wafer test to multi-position, singulated devices. The advantages of these sockets can be enormous as test time can be decreased by a factor of ten over conventional one up testing. In most cases, the throughput is only limited by tester capabilities and/or handling capacity.
-
Product
Wafer Probe Heads
-
WLCSP test is the applying final test conditions at Wafer Level. WLCSP testing is driven in lowering the cost of test of devices through economical methods of manufacturing and testing.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-3010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±8 kV*High pulse output current up to ±30 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
Semi-Automated Probe Stations
SPS 2600, SPS 2800, and SPS 12000 Series
-
The SPS 2600, SPS 2800, and SPS 12000 Series systems are MicroXact’s semi-automated probe stations designed to be flexible and easy to use when performing high productivity device characterization, wafer level reliability testing and failure analysis. These semi-automatic probe station systems are designed to support manual and semi-automatic probing of up to 200mm wafers.
-
Product
Humidity Sensors
-
digital humidity sensor with integrated temperature sensor that provides excellent measurement accuracy at very low power. The device measures humidity based on a novel capacitive sensor. The humidity and temperature sensors are factory calibrated. The innovative WLCSP (Wafer Level Chip Scale Package) simplifies board design with the use of an ultra-compact package. The sensing element of the HDC1008 is placed on the bottom part of the device, which makes the HDC1008 more robust against dirt, dust, and other environmental contaminants. The HDC1008 is functional within the full 40C to +125C temperature range.
-
Product
High Power Devices
-
SemiProbe configures our PS4L Adaptive Architecture into the Voltarus (TM) family of probe stations to fulfill the unique requirements of testing high power devices at wafer level prior to packaging. Voltarus probe stations are available in manual, semiautomatic, and fully automatic configurations that can test and characterize power devices up to 10 KV or 200 Amps (pulsed).
-
Product
Test Socket Based Elastomeric Matrix Connectors
-
Z-Axis offers a wide range of high performance test sockets, which are based on our elastomeric matrix connectors, for wide range of IC packages (BGA sockets, LGA sockets, etc.), coaxical, and wafer level; and for testing high speed, digital, analog, and RF signals etc.
-
Product
X-ray Inspection Performance
MXI Quadra 7
-
Ultimate image quality and magnification, Quadra 7 reveals quality defects as small as 0.1 µm. Ideal for root cause failure analysis, wire bond integrity checking, component cracking, MEMS inspection and wafer level components including TSV and wafer bumps.
-
Product
Wafer/Dicing Frame Prober
WDF 12DP+
-
The WDF 12DP is a prober/handler capable of transporting and testing standard 300-mm wafers and dicing frames without need of a changeover kit. To support multiple tests after dicing, it has a special positioning function that differs from former types, as well as image-processing functions such as wafer level packaging.
-
Product
Multisite Probe Card
T300 ButtonTile™
-
The Celadon T300™ probe cards are designed for long-term, multi-site, high-density wafer level reliability or burn-in tests up to 400°C. In today’s economic environment, conventional reliability data is needed quickly while eliminating the cost, electrical stress, and delay of parts packaging while maintaining a wafer performance map.
-
-
Product
Probe Card
VC43™/VC43EAF™
-
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliability testing. Cards can be configured up to 104 probes in either single or dual layer with near vertical probes to minimize scrub lengths on pads allowing the VC43s to probe pads as small as 30 microns.
-
Product
Probe Card
VC20E Series
-
The 20mm VC20 is a highly adaptable probe card solution for a wide variety of tests including Modeling & Characterization, Wafer Level Reliability or Parametric Test. It can be easily combined with different interfaces to create modular probe cards supporting Keithley, Keysight or other custom tester platforms. Probes can be configured in either single or dual layer.
-
Product
Wafer Level Multi-Die Test System
ITC55WLMD
-
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
-
Product
High Voltage 50 Ω Pulse Generator
TLP-4010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
Nano-focus X-ray Inspection System
X-eye NF120
-
Nano-focus Tube of 400 nano resolution is installed which is specialized for Semiconductor Packaging, Wafer Level Packaging(WLP) requiring detection of Sub-micron defects.Able to trace and inspect defected area precisely by precise movement of axis with Anti-vibration table.Tomography is available if 3D CT module is added and Wafer Bump Automatic Inspection is available from loading to inspection with wafer handler systems.
-
Product
MPI Automated Probe Systems
-
MPI Advanced Semiconductor Test
MPI’s 200 mm and 300 mm automated probe systems are dedicated and designed to address current and future requirements for all facets of Device Characterization for Modeling and Technology/Process Development, Failure Analysis, Design Verification, IC engineering, Wafer Level Reliability as well as special requirements for MEMS, High Power, RF and mmW device testing.
-
Product
Bond Tester for Wafers 2 - 12 inch
Sigma W12
-
Bondtester for wafers or at wafer level 2” – 12” (up to 300 mm)Precise testing and Cold Bump Pull (CBP) testingLarge X/Y stages X: 600mm, Y: 370 mmForce range from 1gf – 10 kgfBump pitch down to 20 µm
-
Product
WLCSP Probe Heads
-
Smiths Interconnect offers Wafer Level Chip Scale Package (WLCSP) Probe Heads utilizing spring probe technology which provide high parallelism in test, superior signal integrity and high speed / RF testing capability.
-
Product
Wafer/Chip/Package Semi-automated ESD Tester
400SW
-
Tokyo Electronics Trading Co., Ltd.
Semi-automated ESD tester featuring Ecdm 400E, Universal ESD Simulator. Used with a manual wafer probing system or a die manipulator, wafer or die level semi-auto ESD test can be done, as well as packaged device test. Damage is detected by V-I curve or leakage current change detection. Stress level and measurement points are programmed by personal computor via GP-IB. Once test terminals are selected, ESD endurance is automatically measured.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-8010A
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/HMM testing*Fast 50 Ω high voltage pulse output with typical 300 ps rise time*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω-configuration*High pulse output current up to ±80 A (short circuit) with 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 300 ps to 50 ns*1 built-in pulse width: 100 ns*Optional external pulse width extensions 5/10/50/100/200/500 ns using an external pulse width extender TLP-8012A5*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
Product
Wafer Inspection Products
-
Sonix provides manual and automated wafer inspection and metrology systems for wafers ranging from 100mm to 300mm, with extensive analysis capabilities at both the wafer and device level. These industry-leading automated wafer inspection systems are used by the world’s top manufacturers to ensure quality from development through production.
-
Product
System to Handle Wafer Levels
AMI AW Series
-
Operator-Free Wafer Inspection, Analysis and Sorting The AW Series are advanced high-capacity, high throughput automated wafer C-SAM® instruments specialized to deliver maximum sensitivity for the evaluation of wafer and device level applications.
-
Product
Impulse Semiconductor High Current Integrated
Transmission Line Pulse Test System
-
The Impulse Semiconductor High Current Transmission Line Pulse (TLP) test system is the tool of choice for extracting ESD parameters for transient protection devices in a package, or at wafer level. With accuracy better than 100 milliohms at 40 amps peak current, the Impulse high current TLP is specially tailored to the needs of today's ESD device designers who must accurately measure low values dynamic resistance irrespective of breakdown voltage.
-
Product
Probe Card
T90™ Series
-
The 90 mm tile was designed for mounting on a standard 4.5″ probe card holder for multi-site wafer level reliability testing. The 1.6 mm (0.062″) thick rails allow the chassis to slip into planarity adjustable probe card holders for most analytical probe stations.
