PXI Express
Bi-directiona data throughput up to 6 GBytes per sec and electro-mechano interoperability with CompactPCI Express.
See Also: PXIe, CompactPCI Express
-
product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
4-Port PCI Express
PEX 8716
The ExpressLane™ PEX 8716 is a 16-lane, 4-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8716 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
product
XMC-to-PCI Express (PCIe) Adapter
9956
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
product
PCI To PCI Express Board
MS 1718
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
product
Flexible x1 PCI Express to PCI Adapter
SKU-041-0X
The Flexible x1 PCI Express to PCI Bus Adapter (Adapter) was designed to convert the x1 PCI Express bus into two 32-bit PCI buses. It allows you to connect up to two 32-bit PCI expansion boards to the motherboard x1/x4/x8/x16 PCI Express connector.The adapter includes a PCI adapter, x1 PCI Express host board and a PCI Express flat cable.
-
product
PXI Chassis, 8-Slot
40-924-001
The 40-924 includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 7 additional 3U peripheral modules.
-
product
PCI Express PLL Test Application
N1081PLCA
Keysight N1081PLCA PCI Express PLL Test Application designed to measure transmitter PLL bandwidth and peaking based on the PCI Express 5.0 TX PLL Specifications. Use N1081PLCA PCIe PLL test software to test, debug and characterize your PCIe designs.
-
product
PXI Instrumentation
Build high-performance, mixed-measurement systems with NI’s easy-to-scale PXI platform.
-
product
PCI Express (PCIe) 5.0 and Compute Express Link (CXL) Protocol Analyze
Your product description goes here.
-
product
PXI SMU
1 channel, potential-free, U/I measurement unit (16 Bit)Maximum ±30V | ±2.5 A | 25 W4-quadrant operation, slew rates up to 500 V/msDigitizer and arbitrary waveform generator (Option)Standards: PXI, PXIe
-
product
PCI Express Filler
SKU-017-01
PCI Express FIller is very useful for solid fixture of x1 and x4 PCI Express boards during production/testing/debugging phases, for example. It prevents the boards from wiggling within their slots.
-
product
PCI Express 64 bit Card
EXC-4000PCIe-64/xx
The EXC-4000PCIe-64/xx card for the PCI Express bus (64-bit) supports an Ethernet channel using the M4KETH module. The module supports 10Mhz, 100Mhz and 1Ghz Full Duplex UDP/IP Ethernet.
-
product
3-Port PCI Express
PEX 8712
The ExpressLane™ PEX 8712 is a 12-lane, 3-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8712 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
product
Compute Express Link (CXL)
Compute Express Link (CXL) is a new high-speed CPU-to-Device and CPU-to-Memory interconnect designed to accelerate next-generation data center performance. CXL technology maintains memory coherency between the CPU memory space and memory on attached devices, which allows resource sharing for higher performance, reduced software stack complexity, and lower overall system cost. This permits users to simply focus on target workloads as opposed to the redundant memory management hardware in their accelerators. CXL is based on a PCI Express 5.0 Physical layer with speeds up to 32GT/s. Teledyne LeCroy provides protocol analysis test equipment to support development and debug of CXL based devices.
-
product
PCI Express A/D Board
AD12-2000 - Dual 12 bit, 2 GS/s, up to 7GB/s DMA
The AD12-2000 series has two 2000 MS/sec 12-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at up to 7 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, at twice the effective memory depth and speed (up to 4 GSPS).
-
product
4-CH 12-Bit 80 MS/s PCI Express Digitizer
PCIe-9814
The ADLINK PCIe-9814 is a PCI Express digitizer providing speedy, high quality data acquisition. Each of the four input channels supports up to 80MS/s sampling, with 12-bit resolution A/D converter. This allows simultaneous recording of signals on all channels with no inter channel phase delay. The extremely large on-board memory enables long recording times even at the highest sampling rates.Unlike parallel PCI buses, PCI Express slots utilize serial point-to-point connection. Each connection pair (lane) can achieve burst connection speeds of 250MB/s. The PCIe-9814, based on x4 lane slot PCI Express technology, provides a clear advantage in that direct connection of each slot allows full transfer bandwidth for each individual card. The ADLINK PCIe-9814 x4 digitizer can be used in any standard PCI Express slot, x4, x8, or x16.
-
product
24-Port PCI Express
PEX 8796
The ExpressLane™ PEX8796 is a 96-lane, 24-port, PCIe Gen3 switch device developed on 40nm technology. PEX8796 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
product
XMC-to-PCI Express (PCIe) Adapter
8613
Our Reverse Compact XMC-to-PCI Express (PCIe) Adapter 4X (8613) permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported.
-
product
PCI Express 16 Isolated Input Digital Interface (3-13V)
8006e
The 8006e PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
product
Full-Size PCI Express Mini Module With SATA
AX92907
*Two independent SATA channels*Fully compatible with SATA revision 2.0 and 3.0 hard drives (HDD) and Solid State Drives (SSD)*Supports RAID 0,1*Two SATA power connectors with +5V*51 x 30 mm
-
product
PXI Signal Conditioning
For RF and Microwave measurements, Keysight PXI signal conditioning modules modify an analog signal to meet the requirements of the next stage for signal processing. Signal conditioning examples include amplification, attenuation, converting and filtering.
-
product
Protocol Analyzer for PCI Express 5.0
Summit T54
The Summit T54 Protocol Analyzer captures, decodes and displays PCIe 5.0 protocol traffic data rates for x1, x2, x4 lane widths.
-
product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
PXI Software
Keysight modular products include software tools to help you quickly access your test equipment and make measurements. The Keysight IO Libraries Suite allows you to display and configure all of the modules in your system such as LXI, VXI, PXI, AXIe and USB. In addition, software drivers support the most common programming environments such as Visual Studio, C, C++, Visual Basic, MATLAB and LabVIEW.
-
product
XMC-to-PCI Express Adapter
7988
The Technobox, Inc. P/N 7988 is designed to adapt a single-wide XMC card to a 16X PCI Express slot. The 7988 supports both P15 and P16 and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
product
PCI Express CONET2 Controller
A3818
The Mod. A3818(*) is a PCI Express x8 card that can plug into both x8 and x16 PC PCI Express slot (V2.0), which allows the control of up to 4 CONET2 independent networks (each network can be made of up to 8 CONET2 slaves).
-
product
PCIe-8431, PCI Express, 8-Port, RS485/RS422 Serial Interface Device
780592-01
The PCIe‑8431/8 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between … 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
PCI Express 8 Reed Relay Output
8012eS
The 8012eS PCI Express digital interface provides eight optically isolated inputs and eight Reed relay outputs (SPST). The isolated inputs are non-polarized and rated for 3-30 VDC. Optical isolation protects the PC and other sensitive equipment from the voltage spikes and ground loop currents that are common to industrial environments.
-
product
COM Express Type 7
COM Express Type 7 with NXP platforms provides super speed I/O, high-bandwidth expansion interfaces, and 10 x GbE interface for data transmission.
-
product
Specialized PXI
PXI is an abbreviation for PCI eXtensions for Instrumentation. It is based on the PCI architecture, a commonly-used standard in personal computers, with an industrial connector. A second connector adds instrumentation-specific signals to the backplane, like clock and trigger signals.
