6U PXI Chassis
See Also: PXI Chassis, 3U PXI Chassis, Portable PXI Chassis
-
product
PXI Single 10 Channel MUX, XLR Connectors
40-735-902-S2
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 16.3k Ohm
40-294-031
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Prototyping Module, 1-Slot, 78-Pin D-Type
40-225A-401
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
CompactPCI 6U 64 bit ATX 3 slot, P1s, P2-5l
102CPCI603-4057
CompactPCI 6U 3 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
product
PXI 8-slot BRIC Multiplexer, 12-Channel, 80-Pole (8 Sub-cards)
40-570A-116
The 40-570A-116 is a 12-channel, 80-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
product
PXI 10A Power Multiplexer, 1-Bank, 16-Channel
40-661A-103
The 40-661A-103 is a single pole, 1-bank, 16-channel PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
product
PXIe-8881, 3.9 GHz 8-Core PXI Controller - The PXIe-8881 is an Intel Xeon 8-Core embedded controller for PXI Express systems
787807-01
PXIe, 3.9 GHz 8-Core PXI Controller - The PXIe-8881 is an Intel Xeon 8-Core embedded controller for PXI Express systems. You use the PXIe-8881 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe‑8881 includes two 10/100/1000BASE‑TX (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive and other peripheral I/O, such as two Thunderbolt 3 ports. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.
-
product
PXI 8 Slot BRIC 99x16 2-pole (9 sub-cards)
40-562A-122-99X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI High Density Precision Resistor Module, 4-Channel, 2.5Ω to 925Ω
40-298-121
The 40-298-121 is a high density programmable resistor module with 4 channels which can be set between 2.5Ω and 925Ω with 0.25Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI Very High Density Multiplexer, 5-Channel, 32-pole
40-670C-022-5/32
The 40-670C-022-5/32 is a 5-channel, 32-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
product
PXI 8-slot BRIC Multiplexer, 6-Channel, 160-Pole (8 Sub-cards)
40-570A-016
The 40-570A-016 is a 6-channel, 160-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.>
-
product
PXI 8-Slot BRIC Matrix, 99x16 1-Pole (9 Sub-cards)
40-562B-121-99X16
The 40-562B-121-99X16 is a high density BRIC8 matrix module with a size of 99x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI Strain Gauge Simulator Module 4-Channel, 3k
40-265-104
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
PXI Power Relay Module, 16xSPST, 16 A
40-161A-001
The 40/42-161A-001 is a PXI/PXIe 16xSPST power relay module and is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock. Electro-mechanical power relays are used wich are suitable for switching loads up to 16 A at 250 VAC.
-
product
PXI 12-Slot BRIC Matrix, 1344x6 1-Pole (16 Sub-cards)
40-558-121-1344X6
The 40-558-121-1344x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
Analog Output/Arbitrary Waveform Generator PXI Card
GX1649 Series
The GX1649 is a 3U PXI digital to analog output board designed specifically for applications where multiple DC or AC analog outputs are required. The GX1649 offers 64 output channels with 16-bits of precision signal sourcing performance and can be used as a DC source or arbitrary waveform generator.
-
product
PXI 8-Slot BRIC Matrix, 66x8 2-Pole (3 sub-cards)
40-562B-122-66X8
The 40-562B-122-66X8 is a high density BRIC8 matrix module with a size of 66x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXIe-5186, 5 GHz, 12.5 GS/s, 8-Bit PXI Oscilloscope
782058-02
PXIe, 5 GHz, 12.5 GS/s, 8-Bit PXI Oscilloscope—The PXIe‑5186 high-speed PXI oscilloscope has two channels with flexible settings for coupling, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 5 GHz of analog bandwidth and flexible measurement configurations. The PXIe‑5186 also features PXI synchronization and data streaming capabilities.
-
product
PXI 4 Slot BRIC 58x6 2A 1-Pole Matrix
40-596-001
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
product
PXI 12-Slot BRIC Matrix, 320x8 1-Pole (5 sub-cards)
40-558-121-320X8
The 40-558-121-320x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 18x12 Matrix Module, 1-pole 2A 60W
40-508-001
The 40-505/506/507/508/509 are a range of medium density matrix modules able to switch up to 2 Amps or 300VDC/250VAC. They are constructed using high quality electro-mechanical relays for high switching confidence.
-
product
PXI 2 Amp MUX, Single 4-Channel 8-Pole
40-635-104
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
8-Slot 32-bit 6U CompactPCI Backplane
cBP-6108F
- PICMG:2.0 R3.0, 2.1 R2.0, 2.5 R1.0, 2.9 R1.0Note- Dimension:202.5 x 262.05 (mm, WxH, vertical insertion view)- Segment:One- cPCI Bus:32-bit/33MHz- System Slot:Right-hand side; System Slot Rear I/O:P3, P4 and P5 rear I/O with AB-type shroud
-
product
CompactPCI 6U 64 bit ATX 4 slot, P1s P2l, RoHS
102CPCI604-40X0R
CompactPCI 6U 4 slot 64 bit low Easycable, system slot left, with ATX connector. It is fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
product
Outdoor Chassis
PXI-8S
Specifically designed after customer requirements, the PXI-8S Outdoor Chassis purpose focuses on applications in measurement technology - outdoor acoustic measurements in this case with the possibility to connect up to 64 microphones. Tailored solutions for complex customer requirements is a challenge we're facing with confidence; got yourself a mission critical application lacking that certain something? Contact us for further evaluation and eventual resolution of your problem
-
product
PXI 8-Slot BRIC Matrix, 220x8 2-Pole (10 sub-cards)
40-562B-122-220X8
The 40-562B-122-220X8 is a high density BRIC8 matrix module with a size of 220x8 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
2-Slot BRIC, 128x8, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-201-128x8
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
20 Channel RF Multiplexer/Scanner PXI Card
GX6021
The GX6021 is a high-density 3U PXI switching card that provides 200 MHz bandwidth and offers four groups of 1x4 multiplexer scanners.
-
product
PXI 10 Banks of 8 Channel 2 Pole MUX
40-615-022-10/8/2
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
product
PXI Switching Instrumentation
6U PXI
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
