Passive Intermodulation
1.) Protocol Independent Multicast - network routing over existing unicast framework. 2.) Passive InterModulation - RF interference generation condition.
-
Product
RF & Microwave Passive Components
-
SHF Communication Technologies AG
SHF’s microwave components are broadband devices suitable up to 110 GHz. Our SHF BIAS TEES are well known but perhaps a slight variation does suit your application even better. DIPLEXERS are bias tees with a certain bandwidth in the low frequency path to combine or separate high frequency and low frequency signals into or out of a single line. DC-FEEDERS are bias tees without the capacitor. Therefore, it provides slightly lower insertion loss in case it is connected to an AC-coupled device which already has a capacitor on its input. Based on our air line construction, these passive components provide resonance-free transmission over the entire operating range.
-
Product
Passive Tapping Device
VDSL Phantom™
-
VDSL Phantom™ is a unique passive tapping device for Lawful Interception (LI) of VDSL2 lines. The device records and stores broadband digital information, offering unique advantages to Law Enforcement Authorities (LEAs) looking to capture data between the target and the service provider premises.
-
-
Product
Passive Components
-
Bias Tees, filters, power splitters, circulators: Passive components from Kuhne Electronic meet highest quality standards. Benefit from our experience in the commercial sector to achieve the optimum for your station!
-
-
Product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB105
-
The FAB105 features a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three 32bit/33MHz PCI slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. The FAB105 is perfect fit for AXIOMTEK's SHB100 and SHB110, which are built around the PICMG 1.3 form factor. The FAB105 is compatible with the AX60501 chassis.
-
Product
Passive Probe, 10:1, 1.5 GHz, 1.3 M
N2874A
Oscilloscope Probe
A compact 2.5-mm probe head diameter, low input capacitance, and fine-pitch probe tip accessories make the N2870A Series ideal for probing densely populated IC components or surface-mount devices used in today’s high-speed digital applications.
-
Product
Passive Probe, 500 MHz, 2.5mm Tip
PP007-WR-1
-
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
Product
Compact Passive and Active Resistor Trimming for Thick and Thin Film
LRT 2000C
-
*Travel: 6" x 6"*Laser : Fiber Laser Ytterbium 1064 nm*Kerf: 30 to 80 micron Adjustable*Pulse width : 80 nano second*Rap Rate: 1 to 1 million Pulse Per Second*Average Power: 20 watts
-
Product
Passive Devices
-
Fiber Splitters, Muxes, CWDM, DWDM, WDM, PON, Fiber Jumpers, Fiber Attenuators.
-
Product
Passive Component ATS
-
Test and packing speeds from 80ppm to1,800ppmStandard functions - Inductance/quality factor test - Winding resistance test - Polarity testOptional functions - Layer short test - Insulation resistance test - Bias current testCircular vibrating plate design feeds inductors steadily and rapidlyIndex disc design eliminates dropped inductorsFour-wire measurement test socket designAutomatic discharge mechanism when feeding errors occurEach test station has an independent NG (No Good) product collection boxTest without packaging function provided, good products gathered in bulk collection boxExclusive data collection software designed for monitoring product quality in real timeReserved stations for number spraying and automatic optical inspectionSwitchable Chinese/English/Japanese operating interfaceEquipment is fast, stable and safe
-
Product
Integrated Passive Devices
-
Macom Technology Solutions Holdings Inc.
MACOM’s new Integrated Passive Devices (IPD) products can be used in a wide range of aerospace and defense, wireless, and test and measurement applications. These IPD devices implement various functions such as baluns, couplers and power dividers, and are available in PQFN or bare die. Operating over the 2 GHz to 20 GHz frequency range our IPD products offer excellent performance over wide bandwidths.
-
Product
Passive Probe Interface Adapter
CX1151A
Digital I/O Adapter
The CX1151A is an adapter for passive probes for the voltage waveform measurements by the CX3300 series Device Current Waveform Analyzer.
-
Product
500 MHz Passive Probe, 2.5mm, 10:1, 10 MOhm
PP023-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
Passive Oscilloscope Probes
5900 SERIES
-
Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.
-
Product
13-slot ATX-supported PICMG1.3 Bus Passive Backplane
FAB114
-
The FAB114 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three PCI Express x1 slots and a total of eight 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Through one PCIe x16 link, this PICMG 1.3 backplane maximize the performance of high-end PCI Express graphics and video cards. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB114 is perfect fit for AXIOMTEK's SHB100 and SHB110. AXIOMTEK also offers versatile 4U industrial chassis specially design for the FAB114, such as the AX61400, AX6156 series and AX61491.
-
Product
3 Way GPS / GNSS Signal Splitter Passive
GPS302
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
RS-232 Passive Tap Module
EZ-TAP™
-
Stratus Engineering’s EZ-Tap hardware module is a low-cost hardware bus analyzer and protocol analyzer solution that uses a traditional dual COM port approach to RS232 interface monitoring.
-
Product
Intermodulation Distortion Measurements For P50xxA/B Streamline Series VNA
S97087B
-
Easily set up and calibrate swept intermodulation distortion measurements (IMD) measurements using the S97087B software application with the P50xxA/B Streamline Series VNA
-
Product
BenchMate Passive- Air Vibration Control
2210 Series
-
BenchMate Vibration-Free Platforms enhance the performance of precision tabletop equipment.The 2210 Series features a Passive-Air design requiring periodic manual leveling.
-
Product
Passive Fiber Network TAPs
-
Passive network test access points (TAPs) are a hardware tool that allows you to monitor your network. Garland Technology offers fiber network TAPs in network speeds of 1Gb, 10Gb, 40Gb and 100Gb. Fiber Network TAPs are passive, purpose-built hardware devices that make a 100% copy of your networks data - without affecting network traffic. Passive network TAPs let your monitoring tools to see every bit, byte and packet®.
-
Product
CP400X, 400 MHz, ±60 V, 10X Attenuation, Single-Ended Passive Oscilloscope Probe
784254-01
High Current Probe
The CP400X is a coaxial passive probe with fixed 10X attenuation for oscilloscopes that provide 1 MΩ input impedance. It is 2 meters in length. The CP400X attaches to BNC connections on both the signal input and instrument sides.
-
Product
6-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/6
-
*1 PICMG, 4 PCI and 2 ISA*Compatible with AX60501 and AX60530*Supports both AT and ATX power supply
-
Product
Extreme Temperature Passive Probe
N7007A
Oscilloscope Probe
Many environmental test engineers today are using standard-temperature probes in extreme temperature condition, which causes physical damage to the probe. Another common practice among environmental test engineers is to simply attach long wires at the end of their probes, which significantly degrades measurement performance due to excessive inductance and reduced bandwidth. Keysight addresses this issue with the N7007A single-end passive probe.
-
Product
10:1, 10 Mohm, 300 MHz Passive Probe
PP016
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
500 MHz Passive Probe for HDO4000, 10:1, 10 MOhm
PP018-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
Passive Imaging & Radiometers
PMMW
-
A low attenuation atmospheric window from 80-110 GHz (W Band) makes this band an ideal candidate for PMMW systems. Passive imagers operate by detecting naturally emitted thermal (black body) radiation from an object. Products available up to 345 GHz.
-
Product
13-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/13L
-
*1 PICMG, 4 PCI and 8 ISA*Compatible with AX61400, AX6145, and AX6156LE*Supports both AT and ATX power supply
-
Product
Passive Probe, 500 MHz, 10:1, 1 MOhm/10 MOhm
PP020-1
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.Each passive probe is recommended for a certain oscilloscope, using the right passive probe with the right oscilloscope means that the probe will be properly compensated across the entire bandwidth. Using probes with a different oscilloscope will only let you compensate for low frequencies.
-
Product
Thick Film Passive Element
GBR-250
-
GBR-250 series high voltage resistors are made in a thick film technology on ceramic substrates (Al2O3 96%). These elements are used in high voltage applications.
