A/D Converters
quantization of an analog signal into a digital signal.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787457-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
Vector And Scalar Mixer/Converter Measurements
S93083B
The S93083B provides both fully calibrated vector and scalar measurements of mixers and frequency converters, with intuitive, easy-to-use user interface
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 40 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5931-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4I.4470-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-01
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
NI-5772, 1.6 GS/s, 12-Bit, 2.27 GHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
782097-02
The NI‑5772 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that can simultaneously sample two channels at 800 MS/s or sample one channel at 1.6 GS/s with over 2 GHz of analog bandwidth. You can use the NI‑5772 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
product
Compressed Air RH+T Transmitter
T3419P-2
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Static Frequency Converter Systems
Our software and connectivity devices incorporate all the features you need to proactively manage your systems, from basic monitoring and shutdown to predictive analysis and power management. Aplab Integration Services offer complete solutions tailored for the specific requirements of Defense Services, Telecom and Commercial markets.
-
product
Process Indicators & Field Devices
Field devices from the Field Analog series record and convert signals from resistance temperature detectors, thermocouples, resistance-type sensors, and voltage sensors directly on site.
-
-
product
Pulse Rate to 4-20mA or Voltage Converter
SY020
The SY020 Pulse Rate Converter can be linked to any frequency generating device e.g. flow meters, which gives TTL, pulse Reed switch or coil output, converting the frequency to an analogue signal. This can be 4-20mA loop current or a voltage output. The 4-20mA version unit is loop powered.
-
product
Inverters & Chargers
Sensata | Magnum-Dimensions provides a comprehensive range of inverters, inverter/chargers and converters that combines the smart technology you want with the rugged and durable design structure you need.
-
product
Transistor Arrays
Renesas' portfolio of transister arrays include NPN, PNP, NPN-PNP combination transistor arrays based on our complementary UHF-1 SOI process. This portfolio also includes ultra high frequency transistor arrays for VHF/UHF amplifiers, VHF/UHF mixers, IF converters, synchronous detectors. Dual long-tailed pair transistor arrays and Gilbert Cell UHF transistor arrays are also available for wireless communication systems, radio and satellite communications and high performance instrumentation.
-
product
1-Channel DAQ Module
FMC160
Sundance Multiprocessor Technology Ltd.
The FMC160 provides one 12-bit A/D channel at 3.6Gsps and one 14-bit D/A channel at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC160 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
Motor Starting & Control Resistors
Motor Starting Resistors are used to reduce the voltage at the motor terminals and also decrease the starting current. Motor Starting Resistors are necessary because the self resistance of a motor armature is very low. When the voltage is first applied, excessive current will flow. For limiting this current, since there will be no resisting back electromotive force (emf),some series resistance can be added to the armature windings.
-
-
product
Autonomous Capacitive Data Collector
DCX-38
KELLER AG für Druckmesstechnik
The DCX-38 data loggers are designed for water level measurements with a high resolution in the mbar range. They can detect water levels with a total error band of just 1 mm (measuring range 0,5 m water column, compensated temperature range -10...40 °C). Thanks to their long-life battery, they can keep measuring the water level, water pressure and temperature for years (up to 10 years at a rate of one measurement per hour). The logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, converted into fill levels or other units, and exported.
-
product
Embedded LO Capability
S96084B
Enables accurate measurement of relative phase and absolute group delay of a frequency converter with a built-in LO source, without having to access a common reference signal
-
product
PXIe-7868, Kintex-7 325T FPGA, 18-AO Channels, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
785571-01
Kintex-7 325T FPGA, 18-AO Channels, 1 MS/s, PXI Multifunction Reconfigurable I/O Module—The PXIe-7868 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 18 analog output channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7868 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7867 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
JTAG External Modules for Cluster Test
JEMIO
The JTAG External Modules JEMIO™ for Cluster test are intended to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system. For many designs, Boundary-Scan has adequate access to on-board signals, but signals that go off the board often cannot be tested by a JTAG tester. By adding JTAG access to these off-board signals, JEMIO™ modules can increase the board's JTAG test coverage, possibly reducing the need for implementing another test method or for developing alternative tests to reach the required level of test coverage.
-
product
Signal Conditioners
General Purpose
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
product
PC/104 OneBank Board
EMC2-SoM3-300
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-SoM3-300 to be added to robust and rugged installations for various commercial, medical, industrial and military uses and to enable more versatility the EMC²-SoM3-300 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
product
Pilot Wire
The concept is based on the need to improve the performance of existing pilot wire protection schemes by increasing reliability & availability as well as adding an over current guard function. This can be achieved at considerably lower cost than the replacement of the existing proven protection relays & change over to a fibre optic communication channel.
-
product
16-bit, 100KHz, 8SE/4DIFF A/D Inputs; 4 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
APCI-3120-8-4
*Optical isolation 500 V*8 SE or 4 diff. inputs*Data transfer rate: 100 kHz*16-bit resolution*4 analog output channels*Data transfer rate:30 kHz
-
product
Adjustable Bandwidth Tunable (700MHz-1000MHz)
MFA R&D Tunable
Allows passband centered at any frequency over tuning range while adding the capability to vary passband width. Upon input of desired frequency and bandwidth, the filter tunes center frequency and adjusts bandwidth to provide a custom filtering solution on demand. 1dB bandwidth of 5MHz to 20MHz. Suitable for LTE and other test applications.
-
-
product
PXI-7853, Virtex-5 LX85 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module
780341-01
Virtex-5 LX85 FPGA, 750 kS/s PXI Multifunction Reconfigurable I/O Module—The PXI‑7853 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXI‑7853 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
FMC-HPC ADC Board
FMC121
Sundance Multiprocessor Technology Ltd.
The FMC121 provides two 16-bit A/D channels up to 1Gsps and two 16-bit D/A channels up to 1.4 Gsps data rate with a 2.8 GSPS update rate. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter and Texas Instruments DAC39J84 Digital-to-Analog converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC121 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
Data and Statistical Services
Science, Technology, Engineering and Math (STEM) along with Data Analytics look at raw data and convert it into useful information. Data often has missing fields, invalid entries, and duplicate records. Data can also be in multiple files or formats that need to be decoded and merged together, so it can be used successfully. We use Excel, Python, R, and SAS to process these multiple files to extract useful information our customers can use, making their businesses more profitable.
-
product
PXIe-4135, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-01
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
