-
product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with Virtex-6 FPGA - 6U VPX
Model 57640
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One 1-Channel mode with 3.6 GHz, 12-bit A/Ds- Two 2-Channel mode with 1.8 GHz, 12-bit A/Ds- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 16 Channels, 16 Single-Ended Inputs
DN2.592-16
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
Vector And Scalar Mixer/Converter Measurements
S97083B
S97083B provides fully calibrated conversion gain/loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers
-
product
E/O Converter
LTX-510
The LTX-510 Electrical to Optical Converter is a convenient device that is intended to transmit analogue or digital signals to a remote location via a multi-mode fibre optic cable. The main applications are situations in which the signal of interest has a high common mode voltage with respect to the measuring equipment.
-
product
40 GbE Network Attached Storage
HSR40 AC
Curtiss-Wright Defense Solutions
Handling the incoming data is Curtiss-Wright’s CHAMP-XD2, featuring dual Xeon D processors and two built in 40 GbE interfaces. The processors can easily absorb the incoming data and redirect it to the persistent storage media, using 3rd generation PCI Express (PCIe), enabling the efficient movement of all the data. By keeping the data as PCIe, instead of converting it to SATA and sending it to a SATA storage, the data can be directly pipelined over the backplane to the PCIe-based Non-Volatile Memory Express (NVMe) SSDs.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5942-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
Highly Scalable Gaming Platform Based On 12th Gen Intel® Core™ Processors Supports Up To Eight Independent Displays Including 4K UHD
ADi-SA3X-AD
ADLINK‘s ADi-SA3X-AD all-in-one gaming platform features powerful processing and graphics performance for gaming and retail. Equipped with 12th Generation Intel® Core™ processors, the ADi-SA3X-AD provides compelling graphics performance from a PCI Express 3.0x16 discrete graphics card and/or an embedded Intel® Iris® Xe supporting up to eight independent monitors.
-
product
3.6 GS/sec Ultra Wideband RF/IF Extreme 1/2 ATR Recorder
Talon RTX 2589
- Rugged 1/2 ATR MIL-spec chassis- Designed for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 22 lb (10kg)- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Capable of recording RF/IF frequencies to 2.8 GHz- Ultra Wideband recording with 3.6 GHz 12-bit A/D- Selectable 1.8 GHz dual channel mode- Up to 61 TB of solid state storage in removable QuickPac- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.448-02
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Electric Vertical Test Stand
WDW-L series
Jinan Testing Equipment IE Corporation
Electric Vertical Test Stand is a tensile compressive test stand especially designed to match push-pull force gauge. This series pf electric vertical test stand has good stability, wide application range and is convenient to use. The electric vertical test stand has stepless speed-adjusting uniform motion, digital display of the testing speed and converting mode between manual and automatic operation. The vertical test stand is specialized for tension/compression test, insertion/withdraw test, fatigue test and fracture test.
-
product
4-Channel DAQ Module
FMC144
Sundance Multiprocessor Technology Ltd.
The FMC144 is an analog-to-digital (A/D) and digital-to-analog (D/A) FMC daughter card that provides four 16-bit A/D channels at 370MSPS and four 16-bit D/A channels at 2.5GSPS which can be clocked by an internal clock source (optionally locked to an external reference) or by an externally-supplied sample clock.
-
product
Wideband Digital Down Converter
A Digital Down Converter performs channel access functions in digital receivers. It is used for extracting a channel (frequency band) of interest in a wideband signal. Abaco Systems' wideband DDC core employs a quad DDC architecture to achieve ultra high performances. The core accepts up to 16-bit complex data and can process 1GSPS continuously. With a fully programmable architecture at all stages of the processing, this core combines flexibility and speed and can be used in combination with our dual-channel 1GSPS ADC module.
-
product
Bresle Salt Meter
Elcometer 138
Incorporating a flat sensor, the Elcometer 138 Bresle Salt Meter measures the conductivity of a sample, then automatically converts this to show the density of salts, negating the need for the user to do a manual calculation when working in accordance with ISO 8502-6 or ISO 8502-9.
-
product
Total Stations
Zipp02 Series
With vertical compensation and 2” accuracy the Zipp02 provides you with the precision required for your most demanding jobs at an affordable price without adding complexity. The Zipp02 is the tool of your choice when it comes to checking angles, alignments, grade work and short range leveling.
-
product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
product
Level Control Loop Trainer Model
ULP-24P & ULP-24C
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Level Control Setup comprises of acrylic measuring tank fitted with Level transmitter, control valve, I to P converter, source tank with water pump and necessary flexible piping for water circulation. The system is mounted on a table top powder coated metal frame. Level transmitter is of capacitance or DPT type sensor. The electronic panel comprises of ADC and DAC card with RS-232 interfaces.
-
product
DIO-AIO Conversion Set For Conventional Power Amplifier
PAD64
PAD64 DIO(digital input/output)-AIO(analog input/output) Converter is the equipment which could be used for DI/DO (Digital input/Digital output) conversion and galvanic isolation between Real-time simulation system and protection equipment, and any other equipment which need AIO (analog binary input/ output, dry contacts).
-
product
Flame Ionization Detector
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
-
product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 4 Channels, 2.5 GS/s on 8 Channels, 1.25 GS/s on 16 Channels
DN6.225-16
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
product
LXI Remote AC Power Management Switch
60-200-001
If you have ever read the term “programmable except for the supply on/off switch” the 60-200 can provide this capability in a system with the added benefit of an easy to use LXI interface. The 60-200 is a power management switch that provides a means of remotely controlling the power status of up to 8 instruments.
-
product
Modular DC Electronic Load
63600
Chroma Systems Solutions, Inc.
Chroma’s 63600 Modular DC Electronic Load is designed for testing multi-output AC/DC power supplies, DC/DC converters, chargers, batteries, adapters, and power electronic components. They are excellent for use in research, development, production, and incoming inspection applications. The 63600’s state-of-the-art design uses DSP technology to simulate non-linear loads using an unique CZ operation mode allowing realistic loading behavior.
-
product
CHNO Combustion Services
Carbon, Hydrogen, Nitrogen are determined using a 2400 Perkin-Elmer CHN Analyzer. This analyzer uses combustion to convert the sample elements to simple gasses, i.e. CO2, H2O, & N2. Upon entering the analyzer, the sample is combusted in pure oxygen environment at temperatures in the range of 1200-1500 F. The product gasses are separated under steady state conditions, and measured as a function of thermal conductivity.
-
product
High Performance PCIe-GPIB Interface Card
82351B
Convert your PCI computer directly into an intrumentation control; install easily with plug-and-play configuration.
-
product
Temperature and humidity outdoor, indoor probe
T3110
Programmable temperature and humidity transmitter is equipped with temperature and relative humidity sensors. Measured values are also converted to other humidity interpretation - dew point temperature, absolute humidity, specific humidity, mixing ratio or specific enthalpy. Degrees Celsius and Fahrenheit are user selectable. Transmitter contains a microprocessor based control circuitry in a durable plastic case with connection terminals and sensors in a filter with stainless steel mesh. Humidity transmitters is equipped with two galvanic isolated 4-20mA outputs. Configuration of outputs and output range are user adjustable. Large dual line LCD for simultaneous display of T+RH or other humidity interpretation is an advantage. Display is possible to switch off. Computerized design ensures temperature compensation of the humidity sensor and fail indication. State-of-the-art capacitive polymer sensor ensures excellent calibration long term stability, inertia against water and condensation. Transmitters are designed for use in non-aggressive environment.
-
product
DC/DC Converter 3.5 W
REM3.5E-0524S/R10/A
DC/DC converter with 3.5 W from Recom | input ranges 4.5 - 9 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | 10 kVDC isolation
-
product
PXI Signal Conditioning
For RF and Microwave measurements, Keysight PXI signal conditioning modules modify an analog signal to meet the requirements of the next stage for signal processing. Signal conditioning examples include amplification, attenuation, converting and filtering.
-
product
High Accuracy Fibre Optic Inertial Navigation System
SATURN INS
SATURN INS, from Teledyne TSS, is a world leading surface navigation system which offers enhanced unparalleled INS performance which builds on the TSS fibre optic gyro system by adding inertial navigation (INS) capability.As with SATURN, it is available in three standard heading accuracy variants; 0.1° sec lat (SATURN10INS), 0.3° sec lat (SATURN30INS) and 0.5° sec lat (SATURN50INS).
-
product
Converter
ARINC 429
ARINC 429 runs at one of two speeds – 100KHz or 12.5 Khz (nominal). But, the Russians have created an 'ARINC 429 like' standard, which operates at ~ 50KHz. Our customer needed to convert the 50 Khz 'Russian ARINC' to standard high speed ARINC 429, so that their existing test rig would accept it. Our solution all fits in this very small enclosure.
-
product
Temperature and Humidity Regulator
H3021
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
USB / RS232 / RS485 / RS422 Opto Isolators
USB has now moved from the desktop to more challenging environments, including instrumentation, point of sales, factory & building automation, etc. With our rugged, industrial-grade USB isolators and USB to RS232 / RS485 / RS422 optically-isolated converters, we ensure that your assets are well protected from unexpected events.
