Depth
how far down in.
-
Product
Resistivity Meters
DDR3
-
Integrated Geo Instruments & Services Private Limited
The DDR 3 Resistivity Meter is a specialized version of IGIS Resistivity meters designed for use in Resistivity surveys up to about 200m depth. It utilizes rechargeable batteries as power source to energize the ground thus eliminating the necessity of using the relatively expensive dry cells.
-
Product
Multibeam Echosounder - Deep Water
HydroSweep MD/50
-
The HydroSweep MD/50 is a high resolution multibeam echosounder ideally suited for seabed mapping in mid and shallow water based on a sonar frequency range between 52 kHz to 62 kHz. Beside bathymetric depth information from 5 m to more than 2000 m, sidescan data and backscatter data for seabed classification can be acquired.
-
Product
Oscilloscope, 200 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch interleaved, Fully Loaded DSO with 16 Dig Ch MSO
T3DSO2204HD-MS
-
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
4 Channel Oscilloscope
2565B
-
The 2560B Digital Storage (DSO) and Mixed Signal Oscilloscope (MSO) Series offers 100 MHz, 200 MHz and 350 MHz bandwidth models in a 4-channel configuration, with a sample rate of 2 GSa/s and a maximum memory depth of 200 Mpts. Additionally, these oscilloscopes are equipped with a large 10.1" capacitive touch display that provide 1024 x 600 resolution and intuitive touchscreen gestures.
-
Product
LXI Low Thermal EMF Matrix 1-pole 14x33
60-510-004
-
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset. The 60-510 is designed in accordance with the LXI Standard 1.4 and is supplied in a 2U high, full rack width case with 500mm depth.
-
Product
Cable Route Tracing and Identification
-
Cable pinpointers and fault locators from Megger make the process of cable route tracing and identification quicker and more accurate. These pinpointing systems are portable for everyday fieldwork and provide services from power and telecoms to water, rail and gas utilities. HV and LV buried cables can be traced to a depth of up to 5m.
-
Product
Resistivity Meter for Concrete
Ohmcorr Test System™
-
OhmCorr has two probes spaced 1.97" (5cm) apart which are placed in holes drilled to a depth of 3/8th" (8mm) and filled with conductive gel. The direct digital read-out of resistivity is displayed on the LCD when the control switch is activated. OhmCorr and CorMap, when used together, provide an economical and sound diagnostic system of corrosion in reinforced concrete.
-
Product
1U 18" Short-Depth Edge Server
HPC-6120+ASMB-610
-
1U 18" short-depth edge server with Intel® Xeon® W CPU, 128GB DDR4, and 4 PCIe slots. Designed for reliable edge AI, automation, and data acquisition.
-
Product
3D Micro Coordinate Measurement Machine and Surface Roughness Measurement Device
InfiniteFocusSL
-
With the InfiniteFocusSL you are able to measure form and roughness of your components with only one system. In addition, color images with high contrast and depth of focus are achieved. The robust frame and the intelligent illumination technology provide fast and high-resolution measurement in the laboratory and a production near environment. The measurement system is particularly attractive due to its cost effectiveness, measurement speed and usability. The long working distance in combination with the above average measurement field allows a wide range of applications. Measurements are achieved within seconds, and features, such as a coaxial laser for quick and easy focusing, enhance its usability.
-
Product
Multibeam Echosounder - Deep Water
HydroSweep MD/30
-
The HydroSweep MD/30 is a deep water multibeam echosounder ideally suited for seabed mapping in medium and deep waters down to 7,000 m water depth. The HydroSweep MD/30 utilizes operating frequencies between 24 and 30 kHz to map the acquire bathytric depth information as well as sidescan and backscatter data.
-
Product
Oscilloscope, 350 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch interleaved, Fully Loaded DSO with 16 Dig Ch MSO
T3DSO2354HD-MS
-
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
Handheld Oscilloscope
SHS800X Series
-
The SHS800X series has two non-isolated scope channels and one isolated multimeter channel. Available in 100 and 200 MHz versions, all feature a single ADC with 1 GSa/s maximum sample rate and a single memory module with 12 Mpts memory depth. When two channels are enabled, each channel has a sample rate of 500 MSa/s and a standard record length of 6 Mpts. When only a single channel is activated, the maximum sample rate is 1 GSa/s and the maximum record length is 12 Mpts. For ease of use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
Product
Digital Storage Oscilloscope
DCS-1000B Series
-
*100MHz/70MHz/50MHz Digital Storage Oscilloscope*Waveform update rate up to 50,000wfms/s*256 color gradient 7inches WVGA display*10M memory depth per channel independently*1M FFT mathematical sampling analysis mode*Zoom In/Play and Pause Function*Diversified Trigger Functions*X-Y Mode Display*Go/NoGo Function*Data Log Function*Digital Filter Function*36 Measurement Parameter Selections
-
Product
19" Rackmount Drawer with Keylock, Shielded, 7"H x 20"D
DR-071920-K
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Marine Logging System
SuperSting Marine
-
The SuperSting Marine continuously records and stores data from a GPS receiver. Current is injected every 3 seconds and 8 apparent resistivity values representing 8 depth levels are read for each current injection. Depth of penetration depends on length of the cable and array type. Typically you will see down to aproximately 20% of the electrode spread length.
-
Product
19" Drawer with Writing Surface, Unshielded, 10.5"H x 20"D
DR-101920-S
-
Unshielded drawers with writing surface are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
1U 19” Edge Computing Platform with Intel® Xeon® D Processor
MECS-6120
-
- 1x Intel® Xeon® D-17XX Series family processor- 3x DDR4-2666 RDIMM ECC REG up to 192GB- 2x 2.5” SATA bays and 2x M.2 M Key interfaces- 420mm depth 1U 19” rackmount form factor- Built-in Intel® QAT: SSL (20G), Compression (15G)- Intel® eASIC by card for FEC acceleration- EMC grade: Class B & Advanced chassis management, IPMI v2.0 compliant
-
Product
Releaseit Shallow Water Deck Unit
-
Teledyne Benthos’ new Releaseit Deck Unit and dunking transducer enables communications and acoustic release functionality when used with any of Teledyne Benthos’ R-Series Acoustic releases deployed in shallow water environments. Designed with Teledyne Benthos’ proven engineering and reliability, Releaseit is a value-priced alternative deck unit allowing for basic coastal operations. When paired with our new R500 Shallow Water Acoustic Release, the combined system represents a lower-cost turn-key option for shallow water applications up to 500 m water depth.
-
Product
2U Short-Depth Optimized Chassis For ASMB-62 Series Edge Server Board For Edge Computing.
HPC-6240
-
Supports ASMB-62 edge series motherboardFour 2.5" hot-swappable SATA drive bays (2 NVMe drives in option)Four FH/10.5"L and four FH/HL expansion slots1200W 1+1 redundant power supply with 80 Plus platinum level certificateUltra Slim ODD support in option2U Front Bezel in option
-
Product
PDS Ploughing Software
-
Teledyne PDS Plough supports different ways to monitor your leveling operation. Teledyne RESON provides the software as well as the sensors to accompany the system.Teledyne PDS visualizes the plough in top, profile, and 3D views indicating where leveling has taken place. The position and depth of the plough is logged to a digital terrain model (DTM) which is color-coded for depth. It is possible to display a design depth in the profile views, indicating whether the plough has to be lowered or hoisted.
-
Product
G12 - 12 Module Solution
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
Product
100 MHz Digital Output / Pattern Generator
TE8200
-
The TE8200 is a PXI based, high speed digital output/pattern generator product. The TE8200 is capable of 100 MHz high speed digital output and 512Kb memory depth per channel on its sixteen channels. It plugs into a single 3U PXI slot.
-
Product
Digital output version optical fast DO sensor
RINKO II / II D
-
Rinko II is a digital output version with a fast-response optical DO sensor. The instrument can be easily integrated on platforms, because it works with communications by RS-232C or RS-485 and an external power (12 to 24V DC).Rinko IID has not only a temperature sensor but also a depth sensor. Their models can monitor DO in real time, if you have a personal computer and an external power.
-
Product
In-Situ Metrology Etch
-
In-situ metrology systems are attached to deposition systems on one or several viewports for monitoring the progression of the etch dept during the process in real time. No matter if the required stop depth lies within a layer or at an interface.
-
Product
19" Rackmount Drawer with Keylock, Unshielded, 10.5"H x 20"D
DR-101920-K
-
Unshielded drawers are constructed of 20 ga. CRS and are furnished with ball bearing chassis slides to provide smooth operation. Available for 19" and 24" rackmount in 20", 24" and 30" depths, with or without a keylock
-
Product
Rebar Locator
Profoscope
-
The Profoscope is a versatile, fully-integrated rebar detector and cover meter with a unique real-time rebar visualization allowing the user to actually “SEE” the location of the rebar beneath the concrete surface to a maximum depth of 180 mm. This is coupled with rebar-proximity indicators and optical and acoustical locating aids. Rebar diameter can also be estimated within the specified testing range. The Profoscope combines these unique features in a compact, light device that allows the user to operate this rebar detector with one hand making the task of locating rebars a simple and efficient process. In addition, Proceq’s rebar detector convinces through its intuitive user interface making rebar detection easy.
-
Product
CMOS Camera
MIchrome 20
-
Fuzhou Tucsen Photonics Co.,Ltd
MIchrome 20 is equipped with Tucsens new computational imaging software, Mosaic 2.0, which provides a "real-time image stitching" function. It can generate large-sized mosaic images in a few seconds while moving the stage, which is light, smooth and worry-free! MIchrome 20 also provides real-time depth of field fusion. Turning the focus ring to capture different depth of field points while generating clear depth of field images, fast, accurate and efficient.
-
Product
SEA CLIP™ Sensor & Aqua MER™ Meter
-
The SEA CLIP™ by Swain Meter is a high-quality, hydraulically actuated clamp-on DC ammeter for ROV. It is useful for measuring DC currents in subsea cables, cathodic protection systems, and subsea pipes up to 4” in diameter. The SEA CLIP™ can be used with an optional 200-foot cable to a topside meter, or in concert with the Aqua MER™ subsea meter at depths up to 6900 feet of seawater.The Aqua MER™ ROV meter is based on Swain’s proven MER2™ technology, specially adapted to the demanding requirements of the subsea environment and updated to provide RS-485 communication over twisted pair, or fiber optic data transmission protocols.
-
Product
550 HP Water Brake Chassis Dynamometer
TD-24S
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 8,700 lb (3,946 kg)Capacity: 550 hp at 35 mph (410 kW at 56 kph)Rolls: 24 by 34 in. (610 by 864 mm) 4 front fixed rollsPit Required Depth: 27 in. (686 mm)
-
Product
Bench
-
Imagine having a digital storage oscilloscope (DSO) on the bench with next-generation capabilities. Transcat makes it possible with an diverse selection of benchtop oscilloscopes from manufacturers such as Keysight, Rigol, and Siglent. Our digital bench oscilloscope models offer greater memory depth for capturing single-shot and repetitive signals. They allow you to find glitches and transient events.
