Optical Modulation
See Also: Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Unloaded
510150116
Receiver Module
Primary mating module 510151106. (May mate with other ITA modules, as well.)
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-03
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP8T, 8 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
40-788-012-E
Multiplexer Module
The 40-788-012-E (PXI) and 42-788-012-E (PXIe) are dual failsafe SP8T 8 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, Terminated, 8GHz, 50Ω, SMA
40-883B-002
Multiplexer Module
The 40-883B-002 (PXI) and 42-883B-002 (PXIe) are single 16 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. They are available in 8 to 1 and 16 to 1 configurations in two and three slots respectively.
-
Product
PXI Replacement Microwave Multiplexer Relay
40-785-751-R
Multiplexer Module
Pickering Interfaces PXI Microwave multiplexer modules are suitable for switching 50Ω signals up to 40GHz. The 40-785 is available as a single or dual 6 channel multiplexer, with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode, 9/125 Fiber
40-855A-322-HI
Multiplexer Module
The 40/42-855A-322-HI is a PXI/PXIe dual 2-channel multiplexer with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI 8-slot BRIC Power Multiplexer, 24-Channel, 12-Pole (8 Sub-cards)
40-571A-306
Multiplexer Module
The 40-571A-306 is a 24-channel, 12-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI Very High Density Multiplexer, 99-Channel, 2-Pole
40-675A-002-99/2
Multiplexer Module
The 40-675A-002-99/2 is a 99-channel, 2-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
Thermocouple, Module, Receiver, 90 Series, 64 Position
510104133
Receiver Module
Primary mating module 510108124. (May mate with other ITA modules, as well.) *Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
PXI 8-slot BRIC Power Multiplexer, 2-Channel, 48-Pole (4 Sub-cards)
Multiplexer Module
The 40-571A-002 is a 2-channel, 48-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
COM Express Basic Size Type 6 Module with 11th Gen Intel® Core™, Intel® Xeon® and Intel® Celeron® Processors
Express-TL
Computer on Module
ADLINK’s Express-TL COM Express Type 6 Basic size module is based on the 11th Gen Intel® Core™, Xeon® W and Celeron® 6000 processor, and is the first COM Express module to support PCI Express x16 Gen4, effectively doubling the bandwidth of previous generation COM Express modules. With a combined 8 cores, 16 threads, and up to 128GB memory, the Express-TL brings uncompromised system performance and responsiveness to your solution. Featuring brand new Gen 12 Intel® UHD Graphics and Intel® AVX-512 Vector Neural Network Instructions (VNNI), the Express-TL provides AI inferencing performance as much as 3X higher compared to previous generation non-VNNI platforms. The integrated Gen 12 Intel® UHD Graphics core can be configured to support one 8K independent display or four 4K independent displays (HDMI/DP/eDP). In addition, legacy display interfaces such as LVDS and analog VGA are still supported as build options. Key features for today’s applications are support for 2.5 GbE and USB 3.2 with transfer rates of up to 10Gb/s that can transfer image data from cameras faster than previous generation products. Combined with 8 processor cores at 25W TDP, Intel® AVX-512 VNNI, Intel® OpenVINO™ toolkit and Intel® UHD Graphics, the Express-TL is well suited for AI at the edge applications (AIoT/IoT).
-
Product
PXI-7952, Virtex-5 LX50 FPGA, 128 MB DRAM PXI FPGA Module for FlexRIO
780561-01
FPGA Module
Virtex-5 LX50 FPGA, 128 MB DRAM PXI FPGA Module for FlexRIO—The PXI‑7952 provides flexible, customizable I/O for LabVIEW FPGA. It includes 132 single-ended I/O lines configurable as 66 differential pairs. You can pair the PXI‑7952 with FlexRIO adapter modules that offer high-performance analog and digital I/O. Together, the two modules create a reconfigurable instrument that you can program with LabVIEW FPGA software.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 6GHz, 50Ω, SMA, Remote Mount
40-784B-003-E
Multiplexer Module
The 40-784B-003-E (PXI) and 42-784B-003-E (PXIe) are triple SP6T 6GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, SC/PC Connectors, With Interlock
42-860A-222-HI
Switch Module
The 40/42-860A-222-HI is a PXI/PXIe dual insert/bypass switch with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI/PXIe Microwave Transfer Switch, Dual, 50 GHz, 50 Ω, SMA-2.4, Failsafe, Remote Mount
40-782B-552-E
Switch Module
The 40-782B-552-E (PXI) and 42-782B-552-E (PXIe) dual failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
Product
PXI/PXIe Microwave Transfer Switch, Dual, 40 GHz, 50 Ω, SMA-2.9, Failsafe
42-782B-542
Switch Module
The 40-782B-542 (PXI) and 42-782B-542 (PXIe) dual failsafe transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 40 GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
Product
PXI 2A Multiplexer, 16-Bank, 4-Channel 2-Pole
40-614-002
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 67 GHz, 50 Ω, SMA-1.85, Remote Mount, Terminated, Failsafe
40-785C-473-TE
Multiplexer Module
The 40-785C-473-TE (PXI) and 42-785C-473-TE (PXIe) are triple failsafe SP4T 67 GHz with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe USB Data Comms Multiplexer, 16-Channel
42-737A-001
Multiplexer Module
The 40-737A-001 (PXI) and 42-737A-001 (PXIe) are 16:1 USB data communications multiplexers suitable for switching USB1 and USB2 data and power connections using a 78 way D-Type connector. The data signal paths are 2-pole arranged as differential pairs as defined by the USB standard.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP8T, 8 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-788-011-E
Multiplexer Module
The 40-788-011-E (PXI) and 42-788-011-E (PXIe) are single failsafe SP8T 8 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
4-Ch High Speed Counter/Frequency Module
ADAM-5081
Counter/Timer Module
Minimum Pulse Width: 1μ sec. (Frequency/Counter Mode)Function Mode: Counter (Up/Down, Bi-direction, Up, A/B Phase) FrequencyInput Frequency: Frequency Mode: 5Hz ~1MHz Counter Mode: 1MHz max.Isolated Voltage: 2500 VdcProgrammable Digital Noise Filter: 1~65000μ sec.4 channels for Counter, 8 channels for FrequencyCounter Aux. Function: Initial preset, hi-low alarm setting, alarm digital output mapping, overflag
-
Product
PXI Single SP6T Multiplexer 18GHz 50, SMA
40-785B-521
Multiplexer Module
The 40-785B-521 is a single 6-channel 18GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
FPD Tester Power Module
67393-120-480
Power Module
The 67393-120-480 FPD Tester Power Module is a new generation of small, stable, high reliability AC to DC power supply. It adopts compact mechanical design and uses Chroma FPD Tester for signal input/output that can provide a total solution for testing the signal, control and power of diversified panels.
-
Product
AC Reference Modules
Reference Module
NAI offers a variety of AC reference modules that provide a drive capability to 5 VA. The units are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. These modules are specifically designed for rugged defense, commercial aerospace, and industrial applications.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 26.5GHz, 50Ω, SMA, Remote Mount
40-785C-531-E
Multiplexer Module
The 40-785C-531-E (PXI) and 42-785C-531-E (PXIe) are single SP6T 26.5GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Computer On Modules
COM Express Basic
Computer on Module
COM Express Basic is the latest COM 125mm x 95mm form-factor, including Intel core i, Intel 6th Generation and Intel Atom processor. Because of wide range of processors, Intel core i, Intel 6th Generation and Intel Atom processors, COM Express can provides not only high-speed interfaces like HDMI/DisplayPort, PCI Express, SATA and USB 3.0 for volume data transportation, but also LVDS, PCI, and IDE for legacy applications.
-
Product
PXI Solid State Switch Module, 6xSPST, 10 A
40-182A-011
Switch Module
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 3GHz, 50Ω, N-Type, Remote Mount
40-785C-562-E
Multiplexer Module
The 40-785C-562-E (PXI) and 42-785C-562-E (PXIe) are dual SP6T 3GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP12T, 18 GHz, 50 Ω, SMA, Terminated, Failsafe
40-788-221-T
Multiplexer Module
The 40-788-221-T (PXI) and 42-788-221-T (PXIe) are single failsafe SP12T 18 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
Product
PXI 2 Amp MUX, Dual 32-Channel 1-Pole
40-635-005
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
