PXI Serial Interfaces
See Also: Serial Interfaces
-
Product
Digital Interface Boards
Model 2363 OEM
-
* 114515 Board has same digital capability as the 2363 described above with Serial and GPIB IO.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* GPIB header mates with 113640 or 113642 GPIB Connector/Address Switch Cable Assemblies* Accepts 9-32 Vdc power.
-
Product
Multichannel Interface Card
DAS-429mPCIe/RT8-717
Interface Card
The card complies with the PCI Express support one lane 2.5 Gbps PCI Express. The card’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating ARINC 429 and ARINC 717 interfaces and for performing system simulation both in the lab and in the field.
-
Product
Interface Converter
ZET 7076
-
Previously it was widely thought that it is enough to receive sensor readings and to have remote control over them. But gradually there evolved a need for remote control, i.e. people need to receive sensors readings and to control their performance via Internet (for instance, on a portable device). Such possibility simplifies quite a lot of tasks since one can control performance of a system located at the other end of the city or even a country.
-
Product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
-
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
Product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429
-
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Portable Interface Unit
1553-USB-PIU
-
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
Product
200 KHz LCR Meter w/RS-232 Interface
LCR 200
-
Measurement Parameters : Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and £c. Test conditions : 100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz Basic Accuracy 0.1% ; Test Voltage: 1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only). DMM Functionalities. Dual LCD Display with LED backlit
-
Product
Serial to Ethernet Connector
-
With Serial to Ethernet Connector you can share up to 255 serial devices over network turning your computer into a terminal server. With this serial over network solution any device connected to a COM port can be accessed and used from any spot on the globe as if it were physically connected to the local machine. The data sent by serial port device is transmitted over a TCP/IP network. This is achieved thanks to our virtual serial port technology that emulates standard COM ports behavior and Windows OS treats the virtual ports as the real ones. Although the ports are treated as physical you are not limited to the quantity of physical COM ports and can create COM port connections without occupying real serial ports. With Serial to Ethernet Connector you can: share serial port for incoming connections, connect the port to remote host, or share port using UDP connection. Starting from version 7.0 Serial to Ethernet Connector got absolutely new user interface for even easier creation and management of connections with latter conveniently visualized and more.
-
Product
7" WVGA, 64MB, 128MB(NAND), Serial X3, Ethernet
WOP-207K
-
ARM9™ 32-bit RISC processor with 64 MB SDRAM working memorySupports over 500+ PLC industrial communication protocolsBackup memory 128KB for retaining critical data or parameterSupports the HMINavi Designer development tool free on Windows 10Supports HMINavi Runtime data downloads through Serial, Ethernet, USB portNo limitation on the internal I/Os points used for variety applicationEasy to switch one application to different LCD sizes in secondsSupports operation in both landscape and portrait modePanel mount design ensures easy installation and IP66-rated front panel
-
Product
3U cPCI Sensor Interface Unit
SIU35
-
NAI's SIU35 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communication, Ethernet switching, and processing. The SIU35 uses up to five NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-To-Mission."
-
Product
3U CompactPCI Serial 4-slot SSR w/ RTM w/ Ethernet
1CPCIS-304-R210
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot right, with rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, with connectors for Rear Transition Modules (RTMs) in slots 1 to 3, Ethernet full mesh.
-
Product
Digital USB Sensor Interface AC,DC, IEPE
ROGADAQ2
-
The RogaDAQ2 USB DAQ is developed for highly accurate measurements in the T&M and also for NVH measurements. This USB Front End is optimized for noise and vibration measurements with 2 channel IEPE (ICP®) sensor supply.
-
Product
Serial Converter
USB-COMi
-
The USB-COMi is a USB to RS485 serial converter. It allows easy serial port expansion without requiring IRQ, DMA, or I/O port resources. The converter allows the user to easily and economically connect RS485 devices to a host using USB. The RS485 communications standard is used by DGH sensor based data acquisition modules and many industrial control devices.
-
Product
CompactPCI Serial 3U Backplanes
-
Hartmann Electronic’s cPCI Serial Backplanes are compliant to PICMG CPCI S.0 CompactPCI Serial specification. These backplane are outfitted with a cPCI S.0 system slot for the CPU on either the left or right side and then have up to eight CPCI S.0 peripheral slots.
-
Product
PXI Embedded Controller
PXI-3982
Controller
The ADLINK PXI-3982 PXI embedded controller, based on the 6th generation Intel® Core™ i7 processor, is specifically designed for hybrid PXI based testing systems, delivering a rugged yet stable platform for a wide variety of testing and measurement applications.
-
Product
*PC Interfaces
-
Ophir PC interfaces work on the smart plug principle. This means that almost any Ophir PC interface can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir PC interfaces are also the most precisely calibrated units on the marketת, thus measuring with the highest accuracy. With the versatile Ophir StarLab software, your PC becomes a complete laser measurement station. Ophir also provides software to interface seamlessly with LabVIEW or the user's own software.
-
Product
ANSI X3.28 Interface Board
Model 4804B-7
-
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
Digital I/O Module
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
Product
PXI Chassis for Standalone Operation
OTP2 module no.181
-
PXI chassis for standalone operation with the VPC G12 receiver, also required for mounting the Signal Routing Box
-
Product
PXI Software
-
Keysight modular products include software tools to help you quickly access your test equipment and make measurements. The Keysight IO Libraries Suite allows you to display and configure all of the modules in your system such as LXI, VXI, PXI, AXIe and USB. In addition, software drivers support the most common programming environments such as Visual Studio, C, C++, Visual Basic, MATLAB and LabVIEW.
-
Product
Low speed Serial Interfaces
12C/ 12S/ SPI/ UART
-
Arasan has a diverse portfolio of connectivity IP products including SPI, I2C, I2S and UART. These protocols are vital for the integration of SoCs with peripheral chipsets in order to form a complete hardware platform. They are frequently used by the SoC to configure, control and gather diagnostic information at the platform level to ensure correct operation of the hardware.Arasan's proven Connectivity IP Solutions provides a risk free path to integrating these interfaces in SoC designs:High quality IP cores ensure inter-operability between SoCs and peripheralsIn-house domain expertise ensures a high quality support throughout the SoC development cycleTotal IP solution includes RTL source code, synthesis scripts, test environment and documentation
-
Product
Interface Adapter
DMX-10
-
DMX-10 is, all-in-one ready to use PCIEx to I2C/SPI/GPIO Interface adapter based on system with FPGA and 1x PCIEx PHY. DMX-10 converts PCIEx transactions into the I2C, SPI master or slave transactions and GPIO control functions. DMX-10 turns your PC running Windows, DOS, Linux, MacOS or any embedded OS with PCI support into comprehensive general purpose bus master or slave adapter.
-
Product
Avionics/Vehicles Bus, Serial I/O, Shared Memory, and More
-
Curtiss-Wright Defense Solutions
Curtiss-Wright offers a wide range of solutions for high-speed, low latency communications and shared memory products. These products are offered in a variety of form-factors including PMC, XMC, PCIe and PC/104 cards designed to support popular communications standards including 1553, ARINC 429, CANbus and Serial FPDP.
-
Product
Digital Interface Boards
Model 4863 OEM
-
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
Product
Intelligent Interface Card
IIB-1553-CPCI
-
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.The IIB-1553-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes,with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface.2 Mbytes of dual ported RAM are supplied as standard. The board is supplied with C drivers in source code and Windows menu driven software.
-
Product
Interface Technology Basic Line
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Covers all major standard applications in the control cabinet. It is as unique as our well-known high-end products, but much cheaper. Thus, the Basic Line is ideal for all electrical equipment, engineering companies and many other industries where very good just good enough.
-
Product
100 Pin Breakout Interface
VSI-Breakout-100
-
The VSI-Breakout-100 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
3U Conduction Cooled Power Interface Board, VITA 62
106PIBV301-0000R
-
3U Conduction Cooled VPX Power Interface Board, VITA 62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
Product
PXI SMU/Power Supply Instrument
-
a programmable PXI-Express DPS (Device Power Supply) Card designed for high-accuracy and reliable output power for device test applications. Its compact size, easy level of integration, and high flexibility make the 52310e Series ideal for multi-channel power supplies.
-
Product
Serial Probes
-
Probing a SRIO 1 or 2 serial bus at the transmit or receive end point provides the optimal signal for analysis. Single channel probes are designed to attach at that point providing flexibility for different channel widths.
