PXI Serial Interfaces
See Also: Serial Interfaces
-
Product
PXI 16-Channel 4-Bus 2A Fault Insertion Switch
40-197A-002
Fault Insertion Unit
This 16-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers.
-
Product
PXI Signal Analyzer
-
PXI signal analyzers provide the building blocks for your single or multichannel modular test solution with a small footprint that is scalable and flexible. With a shared processor, frame or chassis, display, and interface, you can tailor your test rack to the needs of your lab. Keysight's PXI and PXIe signal analyzers are ideal for design validation and manufacturing applications that require fast measurements, quality control, product conformance, and test optimization.
-
Product
PXI Resistor Module 2-Channel 2R to 131k
40-293-034
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI BRIC8 1Resource Distributor, 6Bus Matrix
40-569-116
Matrix Switch Module
The 40-569 PXI Matrix BRIC provides a range of high-density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 100VDC/70VAC. These large PXI matrix modules are available in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays.
-
Product
PXI Voltage Amplifier 10K Ohm, SMB
41-650-012
Amplifier
The 41-650 is a 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suite the user’s wiring system.
-
Product
High-Power PXI Switch Matrix Modules
-
These high-power PXI switch matrix modules provide higher current and power ratings than the high-density switch versions. These modules are designed for the switching of AC or DC loads or for controlling large relay or solenoid systems. The solid state relay matrices occupy two PXI slots and are suitable for automotive and aerospace test applications.
-
Product
PXI Precision Resistor Module 6-Channel, 2.5 to 395k
40-297-042
Programmable Resistor Module
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Dual 2 Channel Fibre Optic SC/PC
40-855-222
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI 2 A Relay Module, 26xDPDT
40-139A-202
Relay
The 40-139A-202 (PXI) and 42-139A-202 (PXIe) are 26xDPDT relay modules suitable for high density switching applications with medium power and feature 2 A current capacity with voltage rating to 300 VDC/250 VAC
-
Product
PXIe-6672, TCXO PXI Synchronization Module
780063-01
Synchronization Module
PXIe, TCXO PXI Synchronization Module—The PXIe‑6672 is a system timing controller module. It can drive the PXI star trigger lines, import and export PXI backplane clocks and triggers, generate a high-resolution direct digital synthesis (DDS) clock, and generate a high-stability temperature-compensated crystal oscillator (TCXO) 10 MHz Reference Clock for instrumentation. The PXIe‑6672 allows you to synchronize multiple PXI Express systems, synchronize a PXI Express system with external instruments and equipment, and increase the accuracy of instruments within a PXI Express system.
-
Product
PXI 5A Power MUX, 4-Bank, 11-Channel
40-651-003
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI RTD Simulator Module, 16 Channel, PT1000
40-263-203
Simulator
The 40-263-203 is a 16-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Wireless Sensor Tags & Interfaces
-
NFC and UHF RFID sensor tags offer a highly integrated solution for remote sensor data logging. The tags conform to the specifications of the NFC/ISO15693 as well as the UHF RFID standards. Featuring on-chip temperature sensing and the exclusive cool-Log™ technology, these sensor tags enable innovative and cost-sensitive solutions in food and pharmaceutical cold-chain management, industrial process control, remote monitoring and healthcare applications. NFiC™ ICs from ams lower the barriers to NFC integration in electronic devices thanks to their small footprint, high data rate, flexible data transfer modes, fully passive NFC tag emulation and advanced energy harvesting. NFC/HF interface tags are best suited to demanding consumer and industrial applications such as zero-power device configuration and set-up, feature-rich contactless cards for payment and authentication, smart toys and connected cars.
-
Product
GPIB to Relay Interface Boards
Model 4864 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790659-33
Embedded Controller
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
-
Product
50 Pin Breakout Interface
VSI-Breakout-50
-
The VSI-Breakout-50 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
PXI High Power General Purpose Switch Modules
-
Pickering's PXI high power general purpose switch modules provide a range of high current handling relays suited for high power applications. Lower current versions require one 3U PXI slot, the highest current versions occupy two slots. These modules can be used to switch heavy AC or DC loads and the highest current versions are particularly suitable for automotive test. We also have high power switches available in multiplexer and matrix configurations.
-
Product
PXI 12x4 Matrix, 1 Pole Screened
40-510-021-S
Matrix Switch Module
The 40-510 series of matrix modules feature a wide range of selectable switching configurations (12x4,dual 12x4,12x8 and 24x4). Typical applications include signal routing in ATE and data acquisition systems. Available reed relay formats are 1-pole, 2-pole and 1-Pole screened. The screened version is suitable for switching signals up to 50MHz. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules.
-
Product
Interface Solutions
-
Cohu is the market leader in semiconductor test sockets and has 50+ years of semiconductor test expertise providing optimal test contactor and probe pin solutions for every type of application and challenge, using innovative and sophisticated R&D methods.We offer a full suite of test contactors that provide the electrical interface between the tester and the semiconductor device presented by the test handler; optimizes signal performance via an array of consumable probe pins.
-
Product
NI-9853, 2-Port, High-Speed C Series CAN Interface Module
779429-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
Low-Density PXI Multiplexer Switch Modules
-
Pickering's range of low-density PXI multiplexer switch modules are ideal for applications requiring a lower number of channels and poles. All modules are based on high quality ruthenium reed relays that switch up to 150V, 1.2 Amp with 20W max power or high quality electro-mechanical relays (EMR) that switch up to 300V, 2 Amp with 60W max power.
-
Product
Ethernet-GPIB-USB to Serial Interface
Model 9006
-
* All interfaces provide full communication with the serial device.* Ethernet port supports VXI-11 and raw socket protocols.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* GPIB port is IEEE-488.2 compatible.* USB port uses Microsoft supplied driver to prevent driver problems with operating system change problems.* Serial port provides RS-232 and 2 or 4-wire RS-485 signals.* Supports devices that generate asynchronous messages, devices that respond when queried and smart devices.* Internal webserver for easy configuration from any browser.* Board runs on 5 to 15 Vdc power.* Includes ICS's VXI-11 and VISA keyboard control programs.* Works with Agilent, NI and Kikisui VISA libraries.
-
Product
PXI Multiplexer, Single 48-Channel, 1-Pole
40-632A-021-48/1
Multiplexer Module
The 40-632A-021-48/1 is a single 48-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI High Voltage Switching Modules
-
These high voltage relay switching modules provides solutions for uncommitted relay, matrix and multiplexer applications that need to switch voltages up to 1000VAC. The design of these high voltage relay modules ensures they can withstand high common mode voltages and a protective safety cover is used to shield the switching components.
-
Product
PXI Resistor Module 4-Channel 1R to 63.7R
40-293-011
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI Resistor Module 2-Channel 2R to 32.7k with SPDT
40-293-132
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Human Machine Interface
-
Panasonic Automotive & Industrial Systems Europe GmbH
combines state-of-the-art features and top performance with an outstanding design in an all-metal housing. The range consists of four models in sizes from 4.3", 7", 10.4" and 13.4" TFT color display with LED backlight. All models can be installed in a horizontal or vertical position. The touch terminals are equipped with an Ethernet port and support VNC technology, allowing both remote VNC applications and remote assistance. The HM500 series is programmed with the HMWin software, a simple and intuitive program, yet equipped with advanced features. It is possible to import variables from Control FPWIN Pro, the programming software for Panasonic PLCs, thereby facilitating the synergy between PLCs and HMIs. The products have a 5 year warranty.
-
Product
PXI 3A Power MUX BRIC, 3-Channel, 48-Pole
40-571-003
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI High Density Multiplexer, 4-Bank, 20-Channel, 1-Pole
40-615A-016
Multiplexer Module
The 40-615A-016 is a 4-bank, 20-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI Precision Resistor Module 18-Channel, 1 to 62.1
40-297-011
Programmable Resistor Module
This 18-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
