-
Product
Integrated I-V Test Systems
-
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
Product
Non-steady-state probe for thermal conductivity measurement
TP02
-
Hukseflux Thermal Sensors B.V.
TP02 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at the highest accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The standard TP02 probe has proven suitability in soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials. The Non-Steady-State Probe (NSSP) measurement method (also known as transient line source, thermal needle, hot needle, heat pulse- and hot wire technique) has the fundamental advantages that it is fast and absolute while the sample size is not critical. Hukseflux is specialised in NSSP design. Special models have been developed for in-situ field experiments. For permanent installation in soils, a dedicated model, TP01, is available. TP02 has been designed and tested in collaboration with the Applied Physics Group of Wageningen University.
-
Product
Other Power Electronic Capacitors
-
AC/DC Power Film Capacitors, DC Pulse Current Capacitors, DC Filter Capacitors, Pulse Grade Capacitors, Motor Run Capacitors, Feed-Thru Capacitors and other Customized Capacitors
-
Product
OWON PC Oscilloscope Test Instrument
pc-vds
-
Shenzhen Chuangxin Instruments Co., Ltd.
- Up to 100MHz bandwidth, and max 1GS/s real-time sample rate- 10M record length- Friendly UI : FFT, or X-Y, and waveform 2 views displayed on the same screen- Multi-trigger option : edge, video, slope, pulse, and alternate- USB isolation - less signal inference, more PC protection- USB bus powering, and LAN remote control (optional)- Ultra-thin body design, easy portability
-
Product
Gated Integrator | Boxcar Averager
GIA100
-
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
Product
1.6 GSPS, 14-bit Time-domain Digitizer
ADQ1600TD
Digitizer
The ADQ1600TD is a world-leading 14 bit digitizer optimized for time-domain pulse capture. With its unique 1600 MSPS capture rate, enabled by SP Devices’ ADC interleaving technology ADX, the ADQ1600TD opens for demanding measurements such as time-domain pulse capture and high-speed data recording.
-
Product
Laser Drivers & Controllers
-
Fast Pulse Generators for E/O ModulationFast Laser Diode DriversSeed Laser Pulse PickingMOPA timing and controlCustom Delay and Waveform Generation
-
Product
Ultrafast Fiber Optic Photodetectors
DXM Series
-
The DXM series of Ultrafast Detectors are fiber-coupled photodetectors with wide wavelength ranges, as shown in the plot to the right, that are designed to be used for a variety applications. Each provides a high-fidelity electrical output pulse in response to an optical input pulse, and their clean impulse responses have full width half maxima (FWHM) down to 15 ps.
-
Product
Counter/Timer Board
USB-CTR-15
-
The USB-CTR-15 is an ideal solution for adding portable, easy-to-install, counter/timer capabilities to any PC or embedded system with a USB port. This board is packaged in a small, rugged, industrial enclosure and features 15 independent 16-bit counter/timers. The unit is a true USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The unit is plug-and-play allowing quick connect/disconnect whenever you need additional counter/timer devices on your USB port. The USB-CTR-15 can be used for a wide variety of measurement applications including event counting, frequency measurements, position measurement, pulse counting, pulse-width modulation and pulse generation. The OEM version provides just the board without the enclosure or external screw terminal board and is ideal for a variety of embedded OEM applications.
-
Product
2-18GHz Digitising Receiver
DR068-M1
-
Teledyne Defence & Space (TDS) DR068-M1 Digitising Receiver combines a state of the art broadband frequency measurement receiver with a high dynamic range successive detection log video amplifier to realise a high probability of intercept receiver. Digital signal processing techniques are utitlised to derive pulse parameters which are packaged into a PDW and transferred via a low latency Gigabit Ethernet interface. The DR068-M1 enables new and existing systems to incorporate a wideband high POI pulse detection capability with minimal integrating effort.
-
Product
POWER PROBE 4 MASTER KIT
PPKIT04
-
*Combines the Power Probe 4, PPECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit testing capabilities*Tests for AC/DC voltage in 100ms and 50s resolutions, AC volts RMS and volts peak-to-peak, measure resistance, frequency and pulse width (negative and positive)*Tests fuel injectors, module drivers (transistors) and works as a circuit detector with the PPECT3000
-
Product
Software
-
Test and Control Software is also available for several of our products. All of our software is designed by Pulse Instruments for optimum flexibility and control. Please fill out the following form to request an evaluation copy.
-
Product
Chamber/Pyroelectric Task
-
Radiant's Chamber/Pyroelectric Task sets the sample to a series of temperatures by performingGPIB control of an external thermal device. At each temperature it captures the sample’s polarization response and/or small-signalcapacitance. These are combined to calculate the pyroelectric coefficient. The Pyroelectric Task is to be used with a Radiant Test System and a Linkam Stage (-196C to 600C), Thermal Chambers, Hot Chucks, or a Furnace to automatically measure the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled. Radiant's Pyroelectric measurement Task can be added to Vision at additional cost. This measurement suite fully characterizes the pyroelectric charge (polarization) response of the sample under test. The Pyroelectric Task suite controls various thermal controllers such as Quantum Design, Lake Shore, Delta Design, and many others. Detailed Listing of Thermal Controllers Registered in Vision. The Chamber/Pyroelectric Task is quoted upon request.
-
Product
Timing & Digital Logic ICs
-
Renesas offers a selection of industry standard quartz- and RC-based timing/oscillator ICs along with real time clocks. Timing circuits provide clock pulsing and synchronization in digital systems as well as pulse modulation circuits.
-
Product
ESD Test System
58154 Series
Test System
ESD (Electrostatic Discharge) Test Systems are PXI/PCI controlled module to simulate electrostatic discharge pulse during electronic device testing. The 58154 series offer both ESD STM5.1-2001-Human Body Model and ESD STM5.2-1999-Machine Model. The user friendly software offers programmable and flexible features, such as sampling test on a wafer, ESD model, ESD pulse polarity, ESD pulse interval in a sequence, and automatic testing function.
-
Product
EFI Test Light-Bosch 2
3416
-
Peaceful Thriving Enterprise Co Ltd
Simply for testing: Disconnect the fuel injectors, plug in a Noid. Quickly determines if the electrical signal present at the fuel injectors. Light and crank the engine, a flashing Noid light indicates normal pulsing voltage.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
Servo Motor Drive
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
Device Current Waveform Analyzers
-
The dedicated Current Sensors measure from 100 pA level dynamic current up to 10 A with a maximum of 200 MHz bandwidth. The mainframe acquires the signal from the sensors by a maximum of 1 GSa/s sampling speed and 14-bit and 16-bit wide dynamic range. This combination allows you to measure quite wide range of dynamic current, for example, from standby/sleep state to active state, at a single measurement. In addition, the wide bandwidth and the high speed acquisition enable you to measure high speed pulse response even less than 100 ns previously very difficult with existing instruments.
-
Product
AC Calibration Standard
1U647-001
-
The 1U647-001 is a low cost calibration standard used to determine if a 1U632-100 or a 1U663-100 DMU requires factory calibration. Its portability makes it ideal for field-testing. The standard generates signals that simulate the aircraft’s resolvers, rotary variable transformers (RVTs), and linear variable displacement transformers (LVDTs). The unit also generates a pulse width modulated (PWM) signal, and routes the output of an ARINC 429 source to the different DMU input channels. The calibration standard connects directly to the DMU and replaces the output signals of an active extender card. Discrete switch settings simplify testing. The unit is housed in a rugged aluminum case.
-
Product
Pulse Radar Sensors
-
Non-contact pulse radar level transmitters are available in general purpose and intrinsically safe models for liquids and internisically safe models for solids with light, medium, and heavy dust.
-
Product
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse
T3CP30-100
-
30A, 100 MHz CURRENT PROBE, BNC, AC/DC, 30A rms, 50A Peak Pulse.
-
Product
HyMPulse Pulsed Field Magnetometer
-
Metis Instruments & Equipment NV
Geometry independent M-measurement (patent pending): One probe fits all, no pole shoes per magnet geometry. Measure the actual magnet instead of a prepared standard size sample. Measurement of industrial shapes like segments, cylinders, bricks,... with one probe
-
Product
Benchtop Research System
XENON X-1100
-
The XENON X-1100 is the only low-cost benchtop Pulsed Light system that enables researchers to more easily characterize new processes using XENON’s proven technology.
-
Product
Closed Loop Hall Effect Current Sensors/Transducers
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor
-
Product
Frequency Converter
FC5-29M
-
Frequency converter FC5-29M is a measurement instrument which is designed for spectrum conversion of 75 - 170 GHz to 1 MHz ÷ 2,6 GHz range and automatic frequency measurement of sinusoidal signals. When combined with the 1 MHz - 3,0 GHz spectrum analyzer, FC5-29M can be used for examination of the continuous and periodically repeating pulse signals.The instrument is meant to be used for measurement of various signal sources, radio-transmitting instruments, synthesizers, frequency converters, measurement generators and also for adjustment and verification of various radio-transmitting or communication instruments in laboratory and workshop conditions.
-
Product
Automated Shock Test Systems
AutoShock-II Test System
-
The AutoShock-II is a fully automated series of shock test systems used to measure and identify product fragility levels and evaluate protective packaging. With the simulation of real world shock pulses and impact energy levels, manufacturers can systematically test and optimize product design and packaging. L.A.B. Equipment, Inc.''s fully automated computer controlled shock and data analysis test systems are the critical path in accomplishing this optimization.
-
Product
Non-Linear Pulse Amplifiers
-
These amplifiers have fixed output amplitudes, and are DC-coupled. All models can drive 50 Ohms or higher.
-
Product
Picosecond Laser
PIXEA
-
The PIXEA is a high-quality laser system for OEM and R&D applications generating ultra-short optical pulses by using gain-switched laser diode technologies. The laser features high-quality picosecond laser pulses with no satellite pulses and minimize pulse tail. The PIXEA series offer a large variety of centered wavelengths between 375 nm and 2 um. The pulse duration down to 20 ps is optimized for each wavelength. The system is based in two modules or one module, the laser head and the dedicated Control Unit including the GUI software. Different optical output options are available, including free space collimating optics and fiber coupled.
-
Product
One Wire Communication Board
MS 1727
-
- Digital serial bus communication with low speed data over a single line, Both signaling and driving power over a same single signal.- Protocol used in small inexpensive devices. Such as digital thermometer, weather instruments, laptop sub module, authenticate system and some cell phone battery packs.- Always master only initiates the communication and in overall in charge of the network.- Bus communicates with master and slave at a low data rate of 12kbps.- All terminals in the network are communicating by half-duplex mode.- Maximum of 255 nodes in each 1-wire network- Each data transaction will start with 480micro second low RESET pulse.
-
Product
Incorporated a Convenient LabView Interface to the Output
LabView VIs
-
Several VIs are available for plotting and monitoring pulse parameters. Update rates can be adjusted as well as the plots. The VIs are intended to be easily understood and easily modified for your particular application.
