-
Product
IP Solution
eMMC 5.1
-
Demand for mobile content capacity and bandwidth for video, pictures and music is ever increasing. To address this demand in the next generation of smartphones, tablets, and portable devices, the eMMC 5.1 Specification from JEDEC, improves the current HS400 speeds operating at 3.2Gbps, with "command queuing" making the data transfers highly efficient by offloading the software overhead into the controller. eMMC 5.1 further improves the reliability of operation by utilizing an "enhanced strobe" at the PHY layer. The eMMC5.1 is backward compatible with the existing eMMC 4.51 and eMMC 5.0 Devices.
-
Product
Mini Pneumatic, Contact, ITA, Push-in Fitting, for 6 mm OD Tubing
610132112
-
Primary mating contact 610131112.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
Product
FPP Software
Four Point Probe
-
Materials Development Corporation
For use with a manual four point prober, the MDC FPP Software operates in a convenient, single screen that displays both measurement parameters and testresults. The FPP software can measure Resistivity, Conductivity, Resistance, Doping, Thickness, and SheetResistance when used with a compatible current source and voltmeter or SMU.
-
Product
Avionics Generator
MPG 4010 Series
-
The MPG 4010 Series is fully compatible to Aeroflex NAV 750C, 2030 and 2040 Series GPIB commands, enabling simplified and optimized replacement. Avionics parameters are presented in the same form as described in the ICAO standards. The 4010 Generator is the ideal solution for the testing of avionics on-board LRU and airfield alarm monitors in STTE systems. The use of a Vector Modulator and Digital Modulation Techniques ensures very high accuracy and stable performance over all operating conditions.
-
Product
NI-9852, 2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
779707-01
-
2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI-9852 is a fault‑tolerant Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9852 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9852 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9852 is only compatible with CompactRIO systems.
-
Product
16G SO-DDR4-3200 1GbX8 1.2V SAM -40~85C
AQD-SD4U16N32-SEW
-
DDR4 3200Mhz Unbuffered SO-DIMM, 30u" Gold Plating Thickness, Anti-sulfurization resistance, 1.2V power consumption. Samsung original chip, 100% tested for stability, compatibility and performance.
-
Product
Battery-Powered Flow Totalizer
8150
-
The Signet 8150 Battery Operated Flow Totalizer is compatible with the Signet 515 and 525 flow sensors, and will provide years of dependable operation. The large digital display indicates flow rate and totalized flow volume simultaneously. One of the three totalizers is resettable from the front panel or a remote location, while the second resettable totalizer can only be reset by entering a user-selectable security code. Meanwhile, the third is a permanent non-resettable totalizer.
-
Product
GPIB-RS232, Instrument Control Device
779732-12
-
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
Day/Night IP Surveillance Camera
ENVIROMUX-IPCAM-N
-
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.3 mm (0.17 in), 12 infrared LEDs for night vision. RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
Product
Diode Power Sensor
8487D
-
Excellent SWR for reducing mismatch uncertainty Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 50 MHz to 50 GHzDiode power sensing element
-
Product
3U CPCI To PCI 4 Slot Adapter
-
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
Product
Compatible Adapter Carrier
PCI2PC104p
-
Use your PC/104p boards in a standard PC. Two orientations supported for production mode and test.
-
Product
ARINC 615A Data Loader Software Kit
F-SIM-LDR-615A
-
Avionics Interface Technologies
The F-SIM-LDR-615A software application is an ARINC 615A data loader tool which is compatible with AIT’s family of ARINC 664 interface modules and standard LAN interfaces available on most PC’s. The F-SIM-LDR-615A application supports ARINC 615A load operations over Ethernet and ARINC 664 networks.
-
Product
MIL-STD-1553 Two-Channel PMC Board
BRD1553PMC-STD-2
-
The PMC HyperBoard is a multi-standard PCI Mezzanine Card that contains two channels of MIL-STD-1553 communication. The board is compatible with MIL-STD-1553B and MIL-STD-1760. Each channel can be configured independently to work with H009 and WB-194 in conjunction with MIL-STD-1553.
-
Product
Automatic Antenna Tuner 3.5 kW
DU 3500 AL
-
The DU 3500 AL automatic tuner has been primarily manufactured for an automatic PA, but it can also be used with any manual PAs as well. The tuner is primarily compatible with the OM POWER automatic PA.This tuner was designed for antennas calibrated to HAM BANDs. The maximum power can only be utilized with these antennas. With other antennas, it should be set at a lower power (max. 2kW).The major advantage of the tuner is that during competitions it is possible to change BANDs particularly quickly.
-
Product
Standard Voltage 37 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Registered DIMM
SQR-RD5N
-
Registered DIMM DDR5 4800/5600/6400, Data Transfer Rate: 4800/5600/6400 MT/s. Capacity : 16/32/64/128GB, 100% Screening Test. Compatible with server platform, Original IC chip adopted.
-
Product
SparkFun GPS Breakout
NEO-M9N, U.FL (Qwiic)
-
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Software For Autograph Precision Universal Testing Machines
LabSolutions™ AG
-
The Autograph precision universal testing machines are now compatible with the latest in data integrity.Connecting TRAPEZIUM X-V to the LabSolutions system, which provides ER/ES regulatory compliance, enables confident, reliable data management.In addition to Autograph data, consolidated management is available for LC, GC, and UV data.
-
Product
USB Interface for 1-2 MIL-STD-1553 Channels
NLINE-U1553
-
The NLINE-U1553 implements the latest USB 3 SuperSpeed technology for 1-2 dual redundant, independent 1553 channels. Full function capability for Bus Controller (BC), multi-RT (mRT), and Bus Monitor (BM). Also, o-scope signal capture on the first channel to troubleshoot bus signals. All built-in a small, rugged cable assembly that allows the customer to easily connect with standard 1553 jack connectors, or make their own custom cable with a Lemo break-away standard. USB 2 backward compatible (but not recommended – USB 3 offers superior throughput performance).
-
Product
6U CompactPCI Rear Transition Module with Ruggedized M12 Connectors
cPCI-RMPSA
-
- Dual display with DVI-I and DVI-D- Ruggedized USB 2.0, GbE M12 ports- Dual serial ports and optional USB 3.0- Compatible CPU boards: cPCI-6530/cPCI-6520/cPCI-6940
-
Product
MIL-STD-1553 Eight-Channel PMC Board
BRD1553PMC-STD-8
-
The PMC HyperBoard is a multi-standard PCI Mezzanine Card that contains eight channels of MIL-STD-1553 communication. The board is compatible with MIL-STD-1553B and MIL-STD-1760. Each channel can be configured independently to work with H009 and WB-194 in conjunction with MIL-STD-1553.
-
Product
AC/DC Split Core Current Sensor CT1000S
-
This AC/DC split core current sensor is designed for measuring large DC and AC currents in applications such as electric vehicles, renewable energy systems, inverters, and motors. It facilitates high-current measurements by clamping around existing current connections. With its voltage output, this sensor is compatible with power analyzers (WT series and PX8000) and waveform measurement instruments (ScopeCorders and DLM series), making it a versatile tool for various high-current measurements.
-
Product
SH37F-P-4, 37-Pin Female to Pigtail Shielded I/O Cable, 12ft
778620-04
-
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
-
Product
Development Board
SOM-DH2000
-
Development Board for COM-HPC® Mini pin-out & Size, PICMG COM-HPC Mini pinout. COM-HPC Mini compatible, Rich extension: 1x PCIe x8(Base on PCIe x16 slot), 2x PCIe x4.
-
Product
Safety Relay Unit for PNP Output (Equivalent) Type Light Curtain
SF-AC
-
Panasonic Industrial Devices Sales Company of America
Safety Relay Unit compatible up to control Category 4. This device incorporates power supply terminals and synchronization line terminals for the Light Curtain, so terminal blocks are not required.
-
Product
32-Axis PCIe EtherCAT MainDevice Motion Controller
PCIe-8334
-
ADLINK PCIe-8334 is a hardware-based EtherCAT motion controller able to support up to 32 synchronized axes and over 10,000 points simultaneously. The PCIe-8332 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8334 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party SubDevice are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Signal Conditioners & Interface
-
Modbus RTU Remote Connectivity and Control. Minimize Long Cable Runs with Modbus Network. Pulse to Frequency Conversion. Shaft Speed Pulse to DeviceNet. Shaft Speed Pulse to 4-20 mA Conversion.Sensor Compatibility
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - 3U VPX
Model 52660
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Supports gigabit serial fabrics including PCI Express, Serial RapidIO and Xilinx Aurora- Four 200 MHz 16-bit A/Ds- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
