-
product
Diplexers
ISM and RFID bandpass filter PE8700 from Pasternack is part of our extensive in-stock RF components for sale. Our ISM and RFID band pass filter is manufactured with SMA connectors that are female and in a 4 section design. This 4 section SMA bandpass filter for ISM and RFID has an insertion loss of 1.500 dB and a maximum power of 5 Watts.
-
product
Module Type Amplifiers
Optical amplifier Gain Blocks are compact in size and suitable for built-in use. FiberLabs provides a wide wavelength range of optical amplifier Gain-Blocks over the O-, S-, C- and L-bands. These Gain Blocks can be used for B-PON system using three wavelengths of 1.31 μm, 1.49 μm, and 1.55 μm (ITU-T [compliant with G.983.3]), DWDM system and 100 GbE (IEEE 802.3ba) using the 1.3 μm band.
-
product
Dual Band Radiometer
UVS-AB-T
The UVS-AB-T measures UV-A irradiance and UV-B irradiance.The dual band UVS-AB-T measures the irradiance in two spectral bands with a single sensor providing separate outputs for each band
-
product
Field Meter
AP 01 HD
The AP01-HD is a field meter with total coverage of the terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
product
Rectangular Horn Antennas
SAGE Millimeter wave rectangular gain horns, also called pyramidal gain horns, are offered as both standard and custom models with a rectangular waveguide interface. The pyramidal gain horns only support linear polarization. With a calibrated gain chart, these horns can be used to measure the gain of other antennas by comparing the generated signal levels of both. For this reason, these horns are also referred to as standard gain horns. The listed models offer 23 dB nominal gain, 10/11 degrees typical half power beamwidth and 14 dB/30 dB typical side lobe levels at the center frequency of the band. These horns cover full waveguide bandwidths within the frequency range of 8.2 to 170 GHz. In addition to the models listed below, models with 10, 15, 20 and 25 dB gain and other frequency bands are also available.
-
product
Voltage Controlled Oscillators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
product
Wide Mechanical Tuning Bandwidth Gunn Oscillators
Wide mechanical tuning bandwidth Gunn oscillators utilize high performance GaAs Gunn diodes and various cavity designs to yield near full band frequency coverage. Unlike dual-tuner oscillators, frequency and power optimization are accomplished by a single micrometer. Furthermore, these oscillators can be modified into electrically tunable oscillators by replacing the micrometer with an electrical actuator. The wide tuning bandwidth of these oscillators offers a low cost, high performance means of signal generation, making them ideal test sources for labs and antenna ranges. While standard models offer a waveguide interface, a coaxial interface is also available. When used with a Gunn oscillator regulator/modulator (SOR series), these oscillators can produce AM or FM modulated signals for many test applications.
-
product
SparkFun Transceiver Breakout
NRF24L01+
This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01+. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401A and add some extra pipelines, buffers, and an auto-retransmit feature - very nice!
-
product
Rad Hard GaN FETs
Wide band gap semiconductor technologies such as Gallim Nitride Field Effect Transistors (GaN FETs) have been gaining interest for power management and conversion in space applications. These devices feature higher breakdown voltage, lower RDS(ON) and very low gate charge enabling power management systems to operate at higher switching frequencies while still achieving higher efficiency and a smaller solution footprint. There is an additional benefit from GaN devices that make them attractive to the space market. These devices are inherently immune to total ionizing dose radiation.
-
product
Infrared Camera
TI-240
Shenzhen Calibeur Industries Co., Ltd..
Detector Type: Focal Plane Array, Uncooled MicrobolometerPixel Resolution: 160x120Spectral Band: 8~14μmField Of View: 14°x11°/0.5mSpatial Resolution: 5mradThermal Sensitivity(Netd): ≤50mk@30Focusing: Manual Focus (0.3m~∞)Maximum Frame Rate: 15HzLCD: 2.5′ LCDTemperature Ranges: -20℃~+300℃Accuracy: ±2℃ Or ±2%Temperature Measurement Mode: Real Time Temperature Display, User Defined Points Or Areas of InterestRadiance Correction: 0.01-1.0
-
product
SOA & Raman Amplifier
They are designed for distributed Raman amplification in a narrow spectral range in C band.
-
product
VHF/UHF Handheld Signal Location Antennas
Type NVF-2
The Type NVF-2 series of handheld directional antennas are used to locate interfering signals or noise in either the 420 – 470 MHz (Type NVF-2A) or the 900 MHz ISM band or cellular telephone bands (Type NVF-2B). Both models incorporate a solid reflector positioned behind a resonated half wave driven element, both elements being mounted on a fiberglass rod with an integral pistol grip. The configuration of the reflector and driven element are such that a deep null in the signal being received will occur when the antenna is pointed in the direction of the signal being radiated. A T-pad resistive attenuator is also incorporated in the antenna mounting enclosure to aid in the direction finding process on very strong signals or when excessive reflections present multiple returns.
-
product
Gateway
CODA-4789
Hitron Americas Technologies Inc.
The CODA-4789 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. MoCA 2.0 bonding provides a near-Gigabit wired backbone in the customer’s home for Wi-Fi extension. Its switchable upstream (5~85/5~204MHz) offers the possibility of flexible integration to existing networks.
-
product
Leakage Current Clamp Tester with Bluetooth
M-1141XR
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Waveform display is possible with connection to a smartphone・Measurement data is to be accumulated in the server, and it is available for graph and CSV output・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency (fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
product
Bench Type Panel Meter
ED-305
Standard Electric Works Co., Ltd
● Precision meters for plant maintenance, field servicing and educational purposes.● Taut Band movement with rectifier type.● Multi terminals (4mm socket) for range selection.● Carbon pointer, mirror scale to eliminate parallax error.● High resistance to shock and vibration.● Accuracy：±1.5% F.S.● Scale length：80mm.● Dimension：107(L) × 117(W) × 53(D)mm.● Weight：Approx. 300g.● Meets CE EN 61010-1 CAT Ⅱ 600V EN 61326-1 (for 0~600V)
-
product
Coaxial Waveguide Adapter, 3.5 mm (f), 18 to 26.5 GHz
K281C
The Keysight K281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can be transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.07.
-
product
Broadband Amplifiers
Pasternack broadband amplifier is rated at 1 Watt (30 dBm) Psat and 1.67:1 input VSWR maximum. Our broad band radio frequency amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial broadband amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
product
Motor Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
Dual Station Loaded Motor Tester including Automatic Shaft Engagement, Automatic Bar Code Scanners, Full Spectrum Vibration Analysis (8 bands) with Automatic Accelerometer Placement and Reject Printer.
-
product
Amplified Spontaneous Emissions (ASE) Sources
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
product
0.5-18GHz High Performance Receiver
QR026
The Teledyne Defence & Space (TDS) Single Channel High Performance Receiver provides a new approach for ESM / ELINT applications, incorporating patented features offering wide band synthesized capability from 500MHz to 18GHz, with frequency extensions available up to 40GHz.TDS’s new QR037 digital receiver module combines high dynamic range RF down conversion and LO generation with digitisation and signal processing capabilities to provide a compact solution for a number of ELINT/COMINT and ESM applications.Excellent dynamic range and linearity is achieved through a combination of RF and digital down conversion stages coupled with high performance pre-selection and IF filtering.
-
product
Miniature Axial Extensometers
Model 3442
Jinan Testing Equipment IE Corporation
Weighing as little as 8 grams, these miniature extensometers are designed to have very low operating force with minimal specimen influence. All use an improved version of Epsilon’s dual flexure design which makes them very rugged for their size. With a module height of 15.2 mm (0.6 inches), they will fit in the limited space between grips that is typical with small test samples. Gauge lengths can be as short as 3 mm or as long as 50 mm. A newly designed gage setting pin and assembly allows the gauge length to be set accurately and repeatably to ASTM and ISO requirements for all gauge lengths. Reengineered quick attach wire forms provide simple and secure specimen attachment. Wire forms for round and flat specimens are included, as well as flat, 3-point, and vee knife edges. The wire forms may be removed to enable mounting using elastic bands or springs. A tethering attachment point provides fall protection and enables counterbalancing of the extensometer’s weight when testing delicate specimens.Model 3442 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller and Epsilon will equip the extensometer with a compatible connector wired to plug directly into the controller. For systems lacking the required electronics, Epsilon can provide a variety of solutions for signal conditioning and connection to data acquisition systems, chart recorders, or other equipment.
-
product
Phase Noise Tester 5MHz to 40GHz
Model 7340
Berkeley Nucleonics Corporation
Broad Frequency Range in a single compact instrument from 5MHz to 40GHz. Measurement offsets from .01Hz to 100MHz. Absolute Phase Noise - High Drift mode (ability to measure modulations, high drifting or unstable DUTs, etc.). AM (Absolute Amplitude Noise) measurements. Pulsed Measurement Capabilities. Transient Mode: measure WB Frequency, NB Frequency, NB Phase, NB Power (WB/NB being Wide Band and Narrow Band). Dual channel low-noise integrated power supplies.
-
product
High-Power Multi-Ports Output CATV EDFA (1540~1563nm)
HA5400E (5RU)
Hangzhou Huatai Optic Tech. Co., Ltd.
HA5400E (5RU) series is a high power multi-ports optical amplifier with gain spectrum band within 1540~1563nm. It is mainly designed for the application of CATV or 1~8 continuous banding channel (ITU wavelength). It offers a flexible and low-cost solution for CATV large area coverage of metropolises and medium-sized cities.
-
product
Spectrum Analyzer
S3531
Saluki S3531 series RF spectrum analyzer is designed based on the concept “Smaller, lighter, easier” . S3531 series takes a small desktop space and easy to carry. Most of nowaday RF applications are in this band, like mobile communication (GSM, CDMA, LTE even low frequency 5G), WIFI (2.4GHz), remote control etc, so S3531 series is a good tool for the test, maintenance, R&D of these applications.
-
product
Switches-SP3T
Macom Technology Solutions Holdings Inc.
At MACOM we offer an extensive collection of switches covering multiple commercial and aerospace and defense markets. Our product portfolio has a broad frequency spectrum from DC to 70 GHz. Our silicon Heterolithic Microwave Integrated Circuit (HMIC) PIN diode process is ideal for high power and broadband switches operating from 50 MHz to 26 GHz. Our AlGaAs PIN diode process can extend the upper frequency range of our switch die beyond 70 GHz and is ideal for instrumentation and radar applications. Our GaAs pHEMT and MESFET technology is ideal for fast switching and low control voltage switches optimized for both narrow band and broadband applications. Our 75 Ohm absorptive switches are designed specifically for demanding CATV, FTTx and DBS Infrastructure and CPE applications.
-
product
Analogue (1kV below) Insulation Tester
1800 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Solid state circuitry.● Battery check feature.● Automatic circuit discharge.● Three insulation test voltages.● Color-coded scale.● AC voltage measurement.● Fuse protected.
-
product
SWR / Power Meters
SX240C
Dimensions:170Wx115Hx150DmmWeight:1350gFrequency range:S1 (1.8-54MHz) S2 (140-470MHz)Power display rating:30W/300W/3kW(HF band only)Accuracy of full scale:±10%(F.S.)
-
product
Field Meter
AP 301 FULL HD
The AP301 FULL-HD is a field meter with total coverage of terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
product
UHF/RFID Power Divider Combiner 6-Way, BNC Female, 350-1000 MHz, 30 Watts
PD2561
INSTOCK Wireless Components, Inc
PD2561 is a RoHS compliant, 6 way, wideband, 50 ohm, RF power divider, power combiner furnished with BNC jack female coaxial connectors. All wireless band frequencies in the range from 350 to 1000 MHz are covered with optimal RF performance. Max microwave input power levels up to 40 watts can be handled in both power splitter and power combiner applications. See 6 way power divider input rating tables for additional details.
-
product
VIS-SWIR FPA's
Imaging electronic sensors sensitive in visible, near infrared, short wavelength infrared spectral bands that generate two dimensional electronic images have found mass applications in industry, defense, security, science, environmental protection, medicine etc. Imaging sensors sensitive only in VIS/NIR range are almost exclusively silicon chips manufactured using a series of technologies: CCD, CMOS. ICCD, EMCCD, EBAPS, sCMOS in color or monochromatic versions. Color VIS/NIR sensors are sensitive to light only in visible range when monochromatic VIS/NIR sensors are sensitive up to about 1000nm.
