-
Product
Strain Measurements and Experimental Stress Analysis
-
Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.
-
Product
Instrument Bracket Kit, w/ Strain Relief, Slide Configuration, for 28"+ Slide Kits
310113002
Instrument Bracket
Instrument Bracket Kit, w/ Strain Relief, Slide Configuration, for 28"+ Slide Kits Similar to instrument bracket p/n 310113453, but includes cutout to accommodate air intake on NI PXIe-1088 chassis. Only compatible with slide configurations 28" and longer. Not compatible with cable tray. Not recommended for use with 2+ tier 90 Series systems (905, 9075, etc.).Used to mount testing instrument to slides and also allows test instrument to slide out for maintenance access. Provides strain relief in front area of bracket. Compatible with chassis (see drawing for more information)
-
Product
Strain Relief Plate, Receiver, QuadraPaddle, 480 Position
510109348
Strain Relief
Strain Relief.
-
Product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-8
-
18-bit resolution, unipolar, 16-bit accuracy 8 differential inputs for strain gauges Voltage range 0 to + 2.5 V 8 independant voltage sources for the connected pressure sensors Output voltage for the voltage sources 5 V, 40 mA Gain and offset calibration Calculation of the pressure value through software Programmable gain 16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz 4 digital input channels, 24 V and 3 digital output channels, Open Collector, isolated
-
Product
Hand Dynamometer Logger Sensor
NUL-237
-
This sensor comes with a hand held unit with a built in strain gauge. The sensor measures the pressing force on the hand held unit.
-
Product
Dual Loop Master Controller
-
The Xcite System Master Controller provides all dual loop functions needed for accurate closed loop control and display of the static and dynamic test variables, while producing the highest electro-hydraulic frequency response. At the heart of each Xcite System is the Master Controller, a compact electronic control package which provides all of the controls and displays necessary to operate a controlled force or torque exciter system. The Xcite Master Controller is unique in that it provides electro-hydraulic excitation over a broad frequency range, unprecedented by any previous electro-hydraulic excitation system. It achieves its great frequency range through the use of sophisticated circuitry, high voltage inputs to the servovalve and compression control of the dynamic feedback variable in addition to the conventional servo control of the static loop. Static parameters such as force or displacement may be matched with dynamic control variables such as force, displacement, velocity, acceleration or strain for maximum test flexibility.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 10A, 0.5m
A020GMR-C-0C050
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
High Temperature XY Planar Biaxial Extensometer 1200 C or 1600 C)
Model 7651
-
Jinan Testing Equipment IE Corporation
Model 7651 extensometers measure combined in-plane strains in flat cruciform specimens tested in machines capable of simultaneous X and Y (perpendicular) axial loading and on standard flat samples tested in pure tension. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7651 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to eliminate crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃(2900°F) high temperature option.
-
Product
Non-Contacting Video Extensometer
AVE3
-
The AVE3 is Instron’s most advanced extensometer, engineered for high-precision, non-contact strain measurement across a wide range of mechanical tests—including tension, compression, and flexure. Its adaptable design accommodates various specimen types, sizes, and elongation ranges, making it ideal for everything from delicate films to robust metals. By eliminating the need for clip-on devices, the AVE3 streamlines setup and ensures uninterrupted data collection through specimen failure, even in high-energy break scenarios, such as composites. Compatible with environmental chambers and fluid baths, it supports non-ambient testing with ease. With compliance to ISO 9513 and ASTM E83 and a fast 500 Hz data rate, the AVE3 delivers reliable performance for demanding testing standards.
-
Product
SSG Series Strain Gauge Extensometers
-
Shimadzu’s SSG series of strain gauge extensometers are compliant with ISO, JIS, and ASTM tensile test standards, including those for plastics and metallic materials These lightweight, precision extensometers feature a wide elongation measurement range, while retaining the flexibility to measure using small gauge lengths, and support both rod and flat plate shaped specimens. Consisting of an elongation sensor and amplifier, this extensometer is suitable for use with metals and hard plastic materials, and is fastened securely to specimens with screws. Calibration using an extensometer calibrator allows the extensometer to meet JIS and ISO Class 0.5 and ASTM Class C standards for higher accuracy.
-
Product
Half Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi’s Half Shaft Telemetry System transmits torque signals from rotating shafts to a stationary telemetry receiver. It connects directly to strain gages adhered to the shaft converting it into a torque sensor allowing it to transmit shaft torque while the vehicle is operating. This system is a testing tool used by automotive and racing engineers to obtain real-time torque measurements from vehicle drivelines.
-
Product
15-Pin D-Type Connector, Male
92-960-015-M
D-Sub Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
C Series Universal Analog Input Module
Analog Input Module
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Torque Instrument
-
DTR is a microprocessor based digital indicator, totally autonomousand with input for strain gauge based torque transducers.A ≤±0,02% accuracy makes it possible to be used use in qualitysystems as first or second line sample, periodically calibrated by aSIT center. Measuring system consists of a particularly long-termstable analogue section, of a carrier frequency amplifier whichminimises thermal drifts and of a 16 bits A/D converter whichensures 65.000 internal divisions.
-
Product
Torque Sensor
-
Futek Advanced Sensor Technology, Inc.
Torque Sensors manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), offering a huge selection of Torque Sensors, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.A Torque Sensor, is a transducer that converts a torsional mechanical input into an electrical output signal. Torque Sensor, are also commonly known as a Torque Transducer.
-
Product
NI-9220, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle
865685-01
-
NI-9220, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9220, cDAQ-9171, and cRIO-9940 includes the NI-9220 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9220 features 16 channels and 16 simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. Additionally, you can use the NI-9220 to generate 3.2 MB/s of data at the maximum sampling rate.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Tinned Ends, 1m
A015DF4-T-0A100
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Universal Input Meters
-
Omega offers a large selection of Universal Input Meters that accept a wide variety of input signals including DC voltage/current, process, resistance, strain and temperature.
-
Product
High Temperature Hot Mountable Furnace Extensometers (1200 Cor 1600 C)
Model 3549
-
Jinan Testing Equipment IE Corporation
The Model 3549 is a major advancement in the design of externally mounted, furnace extensometers. This new extensometer is designed to meet the stringent requirements of strain controlled testing as prescribed in ISO 6892, while introducing many new innovative features that help improve productivity with static testing applications (tension and compression testing) and long term testing such as low cycle fatigue and creep. The overall design reduces any influence from common lab environment vibrations. This unit also incorporates a new feature that allows the user to precisely set the contact force against the test specimen. This allows for even and repeatable contact force, limiting contact force induced errors. This extensometer mounts on a slide bracket (included) that can attach to the load frame of your test system; optional load frame mounting brackets are available. The gauge length for the 3549 is automatically set prior to mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 1k
50-265-204
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Shear Beam Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges
-
Product
Benchtop X-ray diffraction (XRD) instrument
MiniFlex
-
New sixth generation MiniFlex X-ray diffractometer (XRD) is a multipurpose analytical instrument that can determine: phase identification and quantification, percent (%) crystallinity, crystallite size and strain, lattice parameter refinement, Rietveld refinement, and molecular structure. It is widely used in research, especially in material science and chemistry, as well as in industry for research and quality control. It is the newest addition to MiniFlex series of benchtop X-ray diffraction analyzers from Rigaku, which began with the introduction of the original MiniFlex system decades ago.
-
Product
Strain Relief Plate, Receiver/ITA, I1/D1
310113531
Strain Relief
Strain Relief Plate, Receiver/ITA, i1/D1
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Ferrules, 0.5m
40-972-015-0.5m-FU
Cable Assembly
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Diametral Extensometers for Rock and Concrete Testing
Model 3975
-
Jinan Testing Equipment IE Corporation
Designed for accurate measurement of small diametral strains such as those required to determine Poisson’s ratio of rock, concrete and asphalt samples. The units are designed to be used in conjunction with the Model 3542RA axial averaging extensometer.
-
Product
4-CH 24-Bit Universal Input USB DAQ Modules (OEM Version Available)
USB-2401
Data Acquisition Module
The USB-2401 is a 24-bit, 4-channel simultaneous-sampling universal input USB DAQ modules featuring built-in signal conditioning circuitry, providing direct measurement of commonly used sensors including current output transducers, thermocouple, RTD, load cell, strain gauge, and others. Individual channels can be programmed to measure different signal types. The USB-powered USB-2401 is equipped with removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 1.5k
40-265-404
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Mechanical Test Fixtures
MMI series man-machine interface
-
Designed to meet the needs of the most discerning customers and the latest market demands, our MMI series guarantees a natural posture for both the operator and the sitting position when performing the test on the adapter. The newly developed lever mechanism, which has been registered as a utility model, is specially adapted to the hand movement of its employee and ensures a heart-loving strain on the operator.
-
Product
Strain Gauge Module
МТМ8
-
Mezzanine module (mezzanine) МТМ8 is designed to measure the output signal of strain gauges. The mezzanine can be used with any bridge sensors (pressure, force, etc.).
-
Product
Averaging Axial Extensometers for Large Compression Samples
Model 3542RA
-
Jinan Testing Equipment IE Corporation
Designed primarily for compressive strength tests on rock, concrete and other large compression samples, this model measures axial strain on opposite sides of the test specimen, and the output is an average of the two readings. Gauge lengths from 1 to 8 inches (25 to 200 mm) and measuring ranges from 0.050 to 0.250 inches (1.2 to 6 mm) are available.
