Line Fault Indicators
See Also: Overhead Line
-
Product
Flap Position Indicators
-
Shows the aircraft flaps positions. It is an internally lighted, dual, self-synchronous, remote reading indicator that has two concentric pointers.
-
Product
Automotive Battery Production Line Tester
-
The Production Line Tester (PLT) is typically installed at the end of battery production lines (finishing). An electrical load test after formation charging is essential to assure performance and quality. The energy discharged during this test must be minimized to eliminate the need for recharging after testing.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A, Hardware Interlock
40-191B-012-HI
Fault Insertion Unit
The 40-191B-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
Single-in-Line Reed Relays
Series 115
-
SoftCenter construction Highest quality instrumentation grade switches Plastic package with internal mu-metal magnetic screen They take up the minimum of board area, conservingboard space Insulation resistance greater than 1E12 Ohms 100% tested for dynamic contact resistance for guaranteed performance 5 or 12 Volt coils with optional internal diode
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Fault Insertion Unit
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
RS-232 Fiber Optic Auto Powered Line Driver
Model 9271
-
The Model 9271 RS-232 Fiber Optic Auto Powered Line Driver features a standard DB9 interface for maximum performance and reliability of data transmission over glass fiber, eliminating the need for serial to nine-pin adapters. In addition, it brings effective data communications to manufacturing environments. I
-
Product
LED Indicators
-
The "semi-analog" LED indicators display the measured value using 71 LEDs. These indicators are designed to withstand very strong vibrations yet have the familiar look of an analog indicator.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A
40-191B-012
Fault Insertion Unit
The 40-191B is a PXI fault insertion switch using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
-
Product
RF In Line Digital Power Meter
DPM-50
-
DPM-50 features high dynamic range, high accuracy and high stability, it works with PC monitoring software and optional handheld monitor to perform real-time in-line monitoring on entire antenna system and saves test data for analysis and evaluation.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
Single-in-Line Reed Relays from Pickering Electronics
SIL / SIP
Reed Relay
The SIL / SIP reed relay is the industry standard when high reliability and consistent performance are desired in a compact package. Pickering Electronics Series 100 - 119 SIL / SIP reed relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding applications. Features include:
-
Product
USB Line Scan Camera
Inexpensive
-
Compact USB line scan camera with high sensitivity and resolutions from 2048 to 4096 pixels. The programming interfaces, including drivers, libraries and programming examples, enable the USB line camera to be integrated into your own application. The line scan camera is supported under the following operating systems:*Windows*Linux*Linux ARM 32Bit (Raspberry PI)*Linux ARM 64Bit (NanoPi M4 & NVIDIA Jetson Nano)
-
Product
Intelligent Cable Fault Locator
TM800
-
TM800 Cable Fault Locator is a portable field instrument working on TDR and bridge methods, adopting advanced micro-electronics technology. It is designed to locate accurate fault points in such cables as telecommunication leadsheathed cable, plastic cable or user’s lead covered wire, while the faults include break, mix, earthing, defective insulation, or poor connecting. It is and ideal function-stable instrument for the field operator to improve work efficiency, in addition, it can also be used for circuitry project checking electric property testing of the cable.
-
Product
In Line Load Cell (200N-5000N)
100 Series
-
Miniature Threaded in Line Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type measures tensile and compressive loads up to 5000N with better than ±0.25% non-linearity.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 4 Channel
40-200-004
CAN Interface
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Bidirectional Weight Indicator
480
-
Large 0.8 in LED 6-digit Display• 100,000 displayed graduations• 523,000 internal counts• Powers up to 10 Load Cells• Tension/Compression operation• NEMA 4X stainless steel enclosure• Measurement Rate up to 40Hz• Selectable filter settings• 0.1uV/graduation signal sensitivity
-
Product
Self testing clamps with Visual Indication
Bond-Rite EZ
-
The Bond-Rite EZ is an easy to use hand-held portable static bonding device that can quickly and securely establish and verify an equipotential bond between equipment for operations conducted in hazardous locations.
-
Product
Line Impedance
KIT
-
The Line impedance kit is composed of two modules, STLG and STSG. The kit is meant to be used with STS 5000, STS 4000 and eKAM in order to perform Line Impedance test.
-
Product
Digital Indicators
-
The precise measuring of dimensions is important for so many enterprises: engineering, surveying, construction, machine tooling and auto manufacturing, just to name a few. And electronic digital indicators provide people in these fields with the means to accurately measure the dimensions of objects both very small and very large by translating small linear distances into rotational movement. Precision measuring tools like electronic digital indicators can also be used to measure distance and range. If your job requires mechanical testing or machining, you may want to shop our selection of dial indicators.
-
Product
PXI 1A Fault Insertion Switch 11-Channel
40-195-101
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
Resistance Bridges - AccuBridge® Line
-
Measurements International Ltd.
The Resistance Ratio Bridge from Measurements International is the next generation replacement. Measurements International is pleased to release the next generation room temperature Direct Current Comparator Resistance Ratio Bridge.
-
Product
Thermocouple Temperature Indicator
CM2-TC
-
CM2-TC Thermocouple Temperature Indicator has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option relay output and an analog output or RS485(Modbus RTU Mode) communication.
-
Product
Wafer Auto Line Integration
-
The line is used for semiconductor wafer grinding. It carries out material matching and distribution, automatic loading and unloading, auto focusing and positioning and many other functions. The grinding precision is 2μm(3-sigma). It is also capable of collecting and analyzing real-time production data and interfacing with MES system.
-
Product
KYZ Indicator and Tester
1031-C3, 1031-C6
-
More than just an indicator, TESCO’s KYZ Indicator and Tester Cat. 1031-C3 (3-wire) and 1031-C6 (6-wire) can also be used to perform accuracy testing of KYZ pulses on all TESCO Next Generation Test Equipment. TESCO’s KYZ Indicator and Testers can be used as a pulse input using the same pickup connection on the front panel of all TESCO Next Generation Test Equipment.
-
Product
PXI 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
40-205-008
Fault Insertion Unit
The 40-205-008 (PXI) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
Cable Sheath Fault Location
-
Locating cable sheath faults is one of the last steps in cable testing, occurring after you have identified the existence of a cable fault via the identification procedure based on your specific site variables and the type of system you are working on
-
Product
Automated Control System for Veneer Edge Gluing Line
Vikat
-
The automated veneer splicing line control system is designed to identify defective veneer areas, control the scrap trimming, bonding of suitable areas and the formation of output sheets of a given size.
-
Product
Pipeline & Cable Fault Locator
TM2000
-
TM2000 Pipeline & Cable Fault Locator is designed for the Underground utilities route locating, the depth measuring and disatance tracing.
-
Product
48-Ch 2A-250VAC 2-Bus Fault Insertion
YAV90076
Fault Insertion Unit
48 channels2A 250V 2 Fault Insertion BusesSwitching up to 60CAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
