Line Fault Indicators
See Also: Overhead Line
-
Product
LISN Line Impedance Stabilisation Networks / AMN Artificial Mains Network
-
A LISN Line Impedance Stabilization Networks / AMN Artificial Mains Network: *supplies the neccessary mains voltage (AC or DC) and current for the Equipment under Test (EuT).*couples interference voltage generated by the EuT and supplies it to the receiver.*provides well defined RF-impedance to the Equipment under Test (EuT)*keeps away unwanted disturbance coming from mains (filter)*protects the mains from unwanted disturbance voltage generated by the EuT
-
Product
Intermittent Fault Detection & Isolation System
IFDIS
-
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
Product
4 Digit Angle Position Indicator (API)
TA-900
-
This has been the New standard in Angle Position Indicators. 4 digit API has fault monitoring for both low-level and loss of signal (LOS) and this status is shown on the front panel led. The unit provides simultaneous connection of both synchro and resolver devices.
-
Product
Guidance Laser with Remote In-Cab Line Adjust
GL3000P
-
The GL3000P Guidance Laser uses an ultra high visibility green laser to establish visual line control for the vehicle driver. Used for highway paint striping, asphalt distributors, road wideners, pavement profilers, or virtually any application requiring vehicle line control. GL3000P model is for truck cab mounting.
-
-
Product
Single-in-Line Reed Relays
Series 117
-
SIL relays - Very High Density Instrumentation & ATE. Smallest board area. 1A version requires 0.15 x 0.27 inches (3.8mm x 6.8mm). 1 or 2 switches with 3 Watts rating. 5 Volt coils with optional diode
-
Product
Line Mounted Detector of PtG and PtP Faults in Line Networks
LineTroll 110EμR
-
The indicator is powered by replaceable long-life lithium batteries which have a life expectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
Power Cable Fault Locators
-
We're professional power cable fault locator manufacturers and producers in China, supplying the best customized service. Feel free to buy high quality power cable fault locator from our factory. All our portable products used in utility locations are with CE certification.
-
Product
Real-Time Online Monitoring to Detect and Analyze Potential Partial Discharge (PD) Signals and Insulation Faults using UHF, AE, and HFCT
PDMonitor
-
Power Monitoring and Diagnostic Technology Ltd.
The PDMonitor, which utilizes Ultra High Frequency (UHF), Acoustic Emission (AE) and High Frequency Current Transformer (HFCT) sensors and is designed to conduct real time online monitoring to detect and analyze potential Partial Discharge (PD) signals and insulation faults before they lead to breakdown or catastrophic failure in power assets. The system provides the developing trend of the PD, when occurring, as alarms in real time, thus helping to predict the insulation degradation status of the asset, prevent sudden accidents, and provide an effective database for Condition-Based Maintenance (CBM) of power assets.
-
Product
6 GHz Programmable Delay Line
PADL6
-
The PADL6 is a programmable delay line instrument designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 6 GHz. Delays are controlled via a TTL level bus.
-
Product
Split-type Cable Fault Location System
-
Weshine Electric Manufacturing Co., Ltd
Electricity networks have had to become more flexible, reacting more quickly to the changes and needs of higher performance. This demand for flexibility is especially true where multiple generation sources occur, such as the intermittent power from renewables like solar and wind energy. While modern SMART grid technology can quickly identify faults in sub-station and generating units, cable faults can still occur anywhere on the network.
-
Product
Single-in-Line (SIL / SIP) Reed Relays
Reed Relay
The SIL / SIP reed relay is the industry standard when high reliability and consistent performance are desired in a compact package. Pickering Electronics Series 100 - 110 SIL / SIP reed relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding applications.
-
Product
Weight Indicators
-
WIM-Systems offers the market an extensive and complete line of weight indicators, weight controllers and weight transmitters , all of them manufactured under the strictest quality standards, based on the technology and experience developed by WIM-Systems throughout the years. several years of successful activities.Our weight indicators, weight controllers and weight transmitters are electronic devices developed with the purpose of translating the information issued by a scale or balance, to data understandable by the operator and in some cases its function also includes the transmission of information from the electronic attachment to the scale.
-
Product
Live Line Clamp Insulation Resistance Tester
MLIT-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy and convenient live line insulation measurements for servo motor,inverter motor and power line.・More than 0.1MΩ for power line.・More than 10MΩ for servo motor and equipment.
-
Product
Cable Fault Locator ECFL 30
ECFL 30
-
Compact precision active/passive, AC/DC bridge with dual channelTDR for fault location on balanced loaded and unloaded cables.
-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A
40-192A-012
Switch Module
The 40-192A-012 is a PXI fault insertion switch using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
Product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Ground Fault Finder
FST-JD200 DC
-
Foresight Electronics Co., Ltd.
FST-JD200 not only can provide a solution on accurately testing the faults of the indirect-grounding of the direct current system, non-metal grounding, loop grounding, simultaneous grounding of the anode and cathode, balanced grounding of the anode and cathode and multi-point grounding 1. The high-precision sampling clamp meter The device uses a high resolution (0.1mA) signal sampling direct current clamp meter that can achieve multi-point grounding and high resistance ground point positioning...
-
Product
High-Resolution Line Camera
X-Scan F
-
High-resolution line cameras for accurate and fast-paced quality inspection, and the grading and sorting of raw materials.
-
Product
Cable Continuity Tester, RS232, DB9 In Line Signal, Network, 21.01 mm, 35 mm, 45.01 mm
72-9265
-
The 72-9265 is an In-Line Signal Link Tester. Quickly test DB9 connections with this handy tester. No need to carry bulky, expensive cable testers to test only one or two cable types. Mini link tester fits easily in your pocket or tool box and requires no external power. Connects in-line and displays signal data connectivity on LED's per each conductor. Save time and money by diagnosing connectivity issues.
-
Product
Magnetic Pole Indicator
-
identification of the field-direction of a magnet (north - south). It simply ascertains, fast and reliably the polarity of permanent magnets and electromagnets. This reliable device is simply to be served. It is indispensable for all industrial areas and fields of investigation which deal with magnetic applications.
-
Product
Cable Fault Location
-
BAUR cable fault location devices and systems cover the entire cable fault location process: During pre-location, the position of the fault is roughly located. The subsequent pinpointing enables precise determination of the cable fault. You can use various measurement methods depending on the kind of fault and cable type.
-
Product
Phase Rotation Indicator DX2
-
STB Electrical Test Equipment, Inc
From the company who builds the popular analog ground fault detector comes the newest phase rotation indicator on the market. No other manufacturer offers a phase rotation indicator like STB's DX2 that will read up to 5kV! The phase rotation indicator is used to determine the phase sequence of three-phase voltages. This meter is most commonly used for phasing-in a power line which has supplied power to motors and plants. It is essential for testing departments of public utility systems for laboratory and field testing. The convenient and durable carrying case allows user to safely transport the unit to wherever the job takes them.
-
Product
Single-in-Line (SIL / SIP) Reed Relays From Pickering Electronics
Reed Relay
The SIL / SIP reed relay is the industry standard when high reliability and consistent performance are desired in a compact package. Pickering Electronics Series 100 - 110 SIL / SIP reed relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding application
-
Product
Voltage Indicators
-
*Measures voltage from 100V to 138kV line‑to‑line.*Can be used individually as voltage indicators or together for phasing operations up to 100 ft (30 m) apart.*Two LED displays are automatically synchronized during phasing operations.*Clear in-phase and out-of-phase indication.*Versatile for overhead and underground applications.*Capacitive Test Point and Peak Hold modes
-
Product
Pitot Static Indicator
ADSE 740
-
The ADSE 740 is a complete high performance dual pressure Ps and Pt standalone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, MACH-meter, air data computers ...) and sensors.
-
Product
Line Drivers
-
The Asynchronous Line Driver (ALD-19.2) utilizes state of the art digital CMOS technology to provide a feature filled product at a very affordable price. The ALD-19.2 transmits and receives data bi-directional at data rates up to 19.2kbps. The unit is designed for asynchronous Point-to-Point operation.
-
Product
Power Line EMI Adapters
-
How much EMI noise is on your power lines indeed? How to assess the levels of noise and its properties when it is obviously a bad idea to connect your oscilloscope or a spectrum analyzer directly to your power lines?Our EMI interface adapters provide a barrier for high mains voltages but a straight passage for high-frequency signals so that you can connect your sensitive instrument to power lines for analysis and quantification. We offer plug-in and hand-held adapters which can measure both differential ("normal") and common-mode noise.
-
Product
End-of-Line IC & MEMS Tester
igentic® 841t
-
Integrated circuit (IC) and micro electro-mechanical system (MEMS) device manufacturers need to address the challenges of today's global market including increased functionality, speed and complexity while delivering components at reduced costs. Sterner Automation's igentic® 841t automated test systems meet these demanding requirements by providing a flexible platform for comprehensive end-of-line IC and MEMS device handling, testing, grading and packaging. The resulting improvements in quality assurance and process efficiency will maximize customer satisfaction and profitability.
-
Product
Switch Indication Maintainer Plus
The SIM-Plus
-
The SIM-Plus - Switch Indication Maintainer Plus is a handheld device used to simulate normal switch correspondence while performing periodic maintenance or testing. The SIM-Plus also provides the ability to power the switch machine using local switch battery or, if battery is not available, provide a temporary source of power from an optional power pack.
