Line Fault Indicators
See Also: Overhead Line
-
product
Ramp or Flight line Air Data Tet Sets
The test sets are all digitally controlled through a local or remote keypad and display. The intuitive user interface allows test set functions to be easily controlled with a minimum of key strokes, with all test parameters displayed, and is suitable for both first time and more advanced users. Optionally many of the ADTS can be remotely controlled by a PDA Pocket PC with wireless Bluetooth connection. The intelligent user interface provides protection to both the test set and the UUT. The software rejects entered command values that exceed the pre-selected limit ranges.
-
product
Test Line • Devices for measuring electrostatic charges
HAUG offers a wide selection of easy-to-use gauges. These are field charges with which electrical charges, fields and potential can be measured. The measured values show how strongly a surface is covered with an electrostatic charge.
-
product
Fault Locator
BIDOYNG
BIDOYNG fits into existing LV fuse positions using two LV fuses in parallel, creating a robust single-shot auto-recloser. The primary fuse carries the load current until a fault causes it to operate. Then, after a user programmed delay, the secondary fuse is switched in and the network re-energised without customer interruption.
-
product
Synchro and Resolver Angle Indicator
AIT5
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used. The resultant data tracks the input shaft perfectly and is always fresh and accurate at input speeds up to 64 revolutions per second, depending on the resolution. Data in BCD or Binary formats are available, and clean, unambiguous crossovers are guaranteed.
-
-
product
Detector of Earth Faults on Multi/Single-Core Terminations
CableTroll 2320
CableTroll 2320 is an indicator for detection of Earth faults (PtG) and short circuit (PtP) faults on multi-core and single core cable terminations. The unit uses NorTroll type current sensors.
-
product
RS-232 Fiber Optic Auto Powered Line Driver
Model 271
FEATURES: Full Duplex to 56 KBPS; 2 Kilometers on 62/125 Fiber; Total Electrical Isolation; Eliminates Noise Problems; ST Connectors; No Power Required. The Model 271 provides feature packed performance and reliability for data transmission over glass fiber.
-
product
Dual-in-Line (DIL / DIP) Reed Relays From Pickering Electronics
Pickering Electronics Series 97 & 98 DIL / DIP Reed Relays feature the highest quality instrumentation grade reed switches making them suitable for the most demanding applications. They are available in two ranges featuring internal mu-metal magnetic screens.
-
product
End-of-Line IC & MEMS Tester
igentic® 841t
Integrated circuit (IC) and micro electro-mechanical system (MEMS) device manufacturers need to address the challenges of today's global market including increased functionality, speed and complexity while delivering components at reduced costs. Sterner Automation's igentic® 841t automated test systems meet these demanding requirements by providing a flexible platform for comprehensive end-of-line IC and MEMS device handling, testing, grading and packaging. The resulting improvements in quality assurance and process efficiency will maximize customer satisfaction and profitability.
-
product
Electronic Fuel Quantity Indicator
Proportional to the amount of fuel in the tank, thereby visibly indicating remaining fuel quantity to the pilot.
-
product
Programmable Delay Line Instrument
The XR Series
A selection of common step sizes that gives you the broadest signal delay range among all our products
-
product
Mobile Cable Fault Location System
BAUR Syscompact 4000
BAUR Prüf- und Messtechnik GmbH
Fault location with Syscompact 4000. The Syscompact 4000 is a compact, fully enclosed fault location system for pre-location and pinpointing of high-resistive, low-resistive and intermittent faults on low- and medium-voltage cables. Easy operation and the use of latest fault location methods enable fast and safe fault location.* Location of low-resistive, high-resistive and intermittent cable faults* Efficient cable fault pre-location methods* Pinpointing according to the noise location method or acoustic propagation time measurement* (with Universal Locator and ground microphone)* Sheath fault location according to the step voltage method (with Universal Locator and two measurement probes)* Easy to handle
-
product
Fault Injection Module
WF 3154 C-Series
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
product
High Line Pressure Transducer
P365
The P365D transducer is designed to make low differential pressure measurements at high static line pressures. Operating from unregulated 9 to 55Vdc, the P365D is available with 4-20mA, 5Vdc or isolated 5Vdc output over full scale pressure ranges from 8 to 10,000 psid. The output shift due to static pressure will not exceed 3% of full scale, up to a line pressure of 10,000 psig.
-
-
product
Platinum Tools Fiber Optic Visual Fault Locator
#TVFL100
Fiber optic visual fault locator works with virtually all 1.25mm and 25mm fiber optic sizes and connector types.
-
product
Fault Detection and Classification (FDC)
E3™
Fault detection and classification (FDC) transforms sensor data into summary statistics and models that can be analyzed against user defined limits to identify process excursions. For process and equipment engineers, maximizing equipment effectiveness, reducing yield excursions, improving product cycle time and enhancing the overall output of the factory are key success metrics. SmartFactory FDC is built on Applied's equipment control technology, the E3 platform, which promotes information sharing.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
The 42-205-008 (PXIe) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
Visual Fault Locator
VFL X5003
Constant & stable output powerLow battery warning, reminds users to change the battery timely.Long battery life (up to 40 hours with AAA batteries)Pocket size and light weight, easy to use.Re-changeable ceramic tube, to avoid returning to manufacturer for this small fault.
-
product
Broadband Digital Signal Delay Lines
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-32Gbps / DC-17GHz) tunable clock/data phase shifterDelay adjustment range of 265psExhibits low jitter and limited temperature variation over industrial temperature range1GHz of bandwidth for the phase adjustment tuning portFully differential CML input interfaceFully differential CML output interface with 600mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 1WFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
product
Voyager Intermittent Fault Detection Tester
This family of testers is available as the portable VIFD™ tester (previously called the Ncompass-Voyager) with 128, 256 or 512 test points, and it is available as a 19” rack-mount system – the IFD & Isolation System (IFDIS™) – with thousands of test points. Testers are available from Copernicus Technology for purchase or lease. Alternatively we can provide the full test service for you and we also provide all the corresponding test accessories listed under the Test Equipment menu button.
-
product
Compact Linear Line Array Loudspeaker
LEOPARD
Say hello to LEOPARD, the most lightweight, versatile line array in its class. The best-selling loudspeaker in the LEO Family faithfully reproduces sound with unsurpassed depth and clarity in a broad scope of installed and touring applications. In Meyer Sound tradition, LEOPARD delivers exceptional phase coherence, consistent coverage, extremely low distortion, and unrivaled power-to-size performance.
-
product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-193A-002
The 40-193A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
product
Line Testers
GAOTek provides a large collection of certified and feature-rich line testers for sale to the United States, Canada and Globally. These devices are mainly used for line installation, line performance testing, inspection, and maintenance of the telecommunication networks. They are particularly designed to accelerate telecom trouble shooting and with the help of latest technology they are equipped with a smart CPU, IC, and SMT. These devices have some unique features such as caller ID display and last number redial. Moreover, it can also be used for multi-line testing, wire pair checking, inspection of line insulation and test for breaks and faults.
-
product
Fault Recorder Software
The Fault Recorder product family is enhanced with our full suite of software applications designed to simplify the process of configuring our records, retrieving event information and analyzing the results. Tools like our automated event retrieval and expert analysis provide the quickest results when classifying an abnormal event. Detailed fault analysis is easily accomplished with our set of power analysis tools and flexible display options.
-
product
Indicators - Electronic
An electronic device used to read an input value from a measuring device and show a displayed value.
-
product
EV Power Components End of Line Test Platform
Test and Validate all EV Power Electronics with One Flexible and Scalable Solution
-
product
Visual Fault Locator
FFL-310-U
FFL-310-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in -CW (continuous) or … MOD (1Hz modulation) mode. There is one LED indicator：with RED or GREEN light; the RED one shows the operating mode of the laser diode output signal, and the GREEN one indicates low battery level. FFL-310-U is designed in a card-size dimensions.
-
product
PLC Line Traps
Line Traps are used in transmission and distribution networks and they are the key components in Power Line Carrier (PLC) systems used for remote control signals, voice communication, remote metering and control between substations in the electrical T&D networks.
-
product
Bleeder, Pressure Indicator - Brake, F/A-18 Hornet
74D130017-1001
F-18 Brake Bleeder. This unit is designed to test, monitor and bleed the brake systems of F/A-18 Hornet fighter aircraft.
