Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 1.51MΩ
40-298-144
-
The 40-298-144 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 750 V Isolation
43-752A-002
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Vehicle Multiprotocol Interface Device
-
The Vehicle Multiprotocol Interface Device excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
One Phase Electric Power/Energy Calibrator
MC133
-
The MC133 master unit model is a one phase electric power/energy calibrator. It can supply the device under test with single phase precise voltage and current with calibrated phase shift along with DC voltage and current capability. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A. Simulated electric power can be set independently for each phase. Frequency can be set from 15Hz to 1 kHz with resolution 0.001Hz to 0.01Hz. The MC133 Calibrator is equipped with 5 1/2 digital DC meter with DC ranges 20mA or 10V for direct calibration of various types of power transducers and wattmeters.
-
Product
PCI Precision Resistor Card 6-Channel, 3Ω To 11.4MΩ
50-297-053
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
ECU Simulator
PT-LabCar
-
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
Product
Bus Switches
-
Bus Switches are devices that enable system architecture to be reconfigured. This reconfiguration is mostly accomplished in the test environment and includes but is not limited to simulation of missile firing and switching in or out a new section of bus interface.Excalibur Systems is the only manufacturer of devices (ESI-R24/27/28) that contain their own TTL driver circuitry that allows them to be directly driven from a computer.
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
-
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
AdvancedTCA, Type 11A, 6U 19" Horizontal, AC
11A06FJB68Y4HGBX
-
Elma's ATCA, AC, 6U horizontal enclosure with backplane, and shelf mgmt. options. Pluggable and redundant fan trays, PEMs and shelf managers for availability (99.999%). Optimized via backplane signal integrity studies and chassis thermal simulation.
-
Product
Kid's Finger Test Probe 19
CX-19
-
Shenzhen Chuangxin Instruments Co., Ltd.
Children Finger Test Probe 19 is intended to simulate access to hazardous parts by children of 36 months or less.
-
Product
MIL-STD-1553 A / B Test And Simulation 3U PXI Module
PXI-C1553
-
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*PXI trigger on 1553 bus events*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems
-
Product
AC Load Bank (Resistive/Capacitive)
K-1000 Resistive/Capacitive
-
Kongter Test & Measurement Co., Limited
A RCD (resistive/capacitive) generator load bank is non-linear load bank. The electronic and non-linear loads simulated by capacitive load banks are typical of the Telecommunications, Computer or Uninterruptible Power Supply (UPS) Industries.
-
Product
*C Series CAN Interface Module
-
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Radar Simulation 3.0
RADSIM
-
RADSIM provides the fidelity and flexibility of a phototexture-based digital radar landmass simulation (DRLMS) system. It uses Leidos-developed core radar simulation technology and can produce a very high-fidelity geo-specific or generic, simulated real-time synthetic aperture radar (SAR), Doppler beam sharpening (DBS), and real beam imagery to less than one-meter resolution.
-
Product
Solar Spectrum Test Chamber / Solar Radiation Test Chamber
-
WEIBER Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. Weiber provide Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Weiber provide Solar Simulation Test Chamber.
-
Product
LASAR Post Processor, Run Time And Diagnostic Test Solution
DtifEasy Series
-
DtifEasy is a full-featured tool set for importing, converting, and executing IEEE-1445 compliant digital test vectors generated by a LASAR simulation. All four IEEE-1445 file types - UUT model group, Stimulus and Response group, Fault Dictionary group, and Probe group are supported by DtifEasy; providing the user with the ability to execute go/no-go, fault dictionary, and guided probe sequences. DtifEasy supports MTS' 3U PXI GX529x series of dynamic digital instrumentation to 200 MHZ as well as the 6U PXI GX5960, 50 MHz digital instrumentation. All of these instrument families are compatible with the digital logic probe.
-
Product
PXI Arbitrary Waveform Generators
-
Keysight's PXI arbitrary waveform generator (AWG) deliver unprecedented performance for creation of complex wideband waveforms. High sampling rate and high bit resolution provided in a single instrument enable designers to create ideal waveforms for accurate test of radar, satellite and frequency agile systems. Providing up to 500 MHz of modulation bandwidths and over 65 dBc of spurious free dynamic range, PXI arbitrary waveform generators can be combined with a wideband I/Q upconverter to achieve modulation bandwidth of 1 GHz at microwave frequencies for realistic signal simulations for IF and RF subsystem test.
-
Product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
-
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
Radio Frequency Scoring Tool
RFST
-
The Radio Frequency (RF) Scoring Tool (RFST) takes the guess work out of RF environment simulation. During RF environment simulation, the RFST provides clear persistent scoring and recording of the RF simulator’s performance. The RFST digitizes all RF signals in the form of digital Pulse Descriptor Words (PDWs) and associated In-phase/Quadrature (I-Q) data. This massive data stream is recorded for later (Post-Scenario) Analysis. Additionally, the RFST provides a real-time visual display of the accuracy of the RF output, easily visible through straight forward real-time indicators. The post analysis tool set allows an unlimited number of users to simultaneously assess previous RF simulator performance with compelling visual representations. The RFST is a perfect complement to our A2PATS product line offering everything you need for comprehensive environment simulation and analysis.
-
Product
Power System Simulator
F6150e
-
This power system simulator performs the simplest through the most complex tests. Meeting all your protective relay testing needs, the F6150e is available in different configurations.
-
Product
Solar Simulator
-
Excellent reputation for its high degree of throughput, accuracy and stability. Pulsed light is used, ensuring stable measurement.Approximates the spectral distribution of AM 1.5G reference solar radiation. Achieves accurate measurement of various modules.No need to reverse modules, facilitating in-line operation.
-
Product
Hot Socket Simulator
Hot Socket Simulator
-
The new TESCO Hot Socket Simulator gives you the ability to investigate meter failure issues related to hot socket phenomenon. The Simulator is equipped with one 2S meter socket with four jaws, one of which is the heated jaw. The arcing/heating apparatus can be moved to any of the four jaws (jaw 1 is the standard). Additional arcing/heating elements can be provided as an option for multiple hot jaws on the existing socket.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-913
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Low Power Programmable AC Power Source With Transients
-
Chroma Systems Solutions, Inc.
Equipped with a host of powerful features: power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, waveshape synthesis and regulation test software
-
Product
DC Power Supply
62000H Series
-
The 62000H Series includes 14 different models ranging from 5KW to 15KW, with current range up to 375A and voltage range up to 1000V. The 62000H can easily parallel up to ten units capable of 150KW with current sharing for bulk power applications, for example, battery bank simulation of 450V/150A/67.5KW for electric vehicle and military use. There are 100 user programmable input status on the front panel for automated test application and life cycle ON/OFF test. In addition, the 62000H has a 16 bit digital control with bright vacuum fluorescent display readout. The 62000H series DC power supplies are very easy to operate either from the front panel keypad or from the remote controller via USB / RS232 / RS485 / APG (Standard) and GPIB & Ethernet (optional). Its compact size with 3U only can be stacked on a bench in a standard rack without any difficulty.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 3k
50-265-102
-
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Network Analysis
-
Network analysis includes a powerful set of analytical tools that allow for simulation, prediction, design and planning of system behavior utilizing an intelligent one-line diagram and the flexibility of a multi-dimensional database.
-
Product
Agile Signal Generators (UXG)
XSeries
-
Get a powerful building block, whether you need a dependable LO or a scalable threat simulator More accurately simulate multi-emitter scenarios for radar, EW and antenna test with the fastest switching, phase coherency, and extensive pulse-modulation Test sooner and increase confidence in EW system performance by generating complex signal simulations when you need them Increase the reliability of your test system: the UXG is a slide-in replacement for legacy fast-switching sources
-
Product
Dynanometer Roller Set
FPS 2700 | VP 230048
-
Maschinenbau Haldenwang GmbH & Co. KG.
The FPS 2700 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. As a result of the increased tractive force of its eddy current brake, the FPS 2700 is additionally suitable for power measurements at constant speed and constant tractive force.
-
Product
High Power & Voltage Pack Testing System
FTF
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery Packs
