-
Product
Shaft Alignment
NXA Pro
-
30 years of innovation continue with the introduction of the NXA Pro.
-
Product
Shaft Speed Sensors
-
Electro-Sensors offers many shaft speed sensors for virtually any environment. Our Hall-Effect and Magnetoresistive Sensors sense magnetic targets and work with our magnetic pulsers (Discs, Wraps, and Wheels). Our proximity sensors sense ferrous metal targets, including bolt-heads, screws, gearteeth and keyslots. Our speed sensors monitor shaft speed of equipment and output data as PNP, NPN, or 4-20 mA signals. The sensor data can be used by facilities to monitor machinery and safeguard equipment. Monitoring shaft speed is a fundamental aspect of hazard monitoring and should be utilized by any facility with rotating shafts.
-
Product
Shaft Speed Sensors - Magnetoresistive
1102 / 932 / 933 XP
-
Features• Square-wave pulse frequency output, NPN open-collector• Zero speed operation with no signal loss• 5-24 VDC powered• 1/2" NPT conduit port (933 XP)• Non-contact, large gap distance sensing• Simple to install and set up• Works with Electro-Sensors magnetic pulser discs / wraps• 1102 – non-threaded stainless steel
-
-
Product
Half Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi’s Half Shaft Telemetry System transmits torque signals from rotating shafts to a stationary telemetry receiver. It connects directly to strain gages adhered to the shaft converting it into a torque sensor allowing it to transmit shaft torque while the vehicle is operating. This system is a testing tool used by automotive and racing engineers to obtain real-time torque measurements from vehicle drivelines.
-
-
Product
Slide Gate & Shaft Position
-
All six Shaft Angle Position Feedback Monitors in the SG1000 Series utilize absolute rotary encoders to provide independent and accurate feedback of a slide gate's or a valve's position to an external device such as a PLC or optional PM500 Process Meter Display Unit. Models are housed in a rugged, Explosion-Proof/Dust-Ignition Proof cast aluminum enclosure that is dirt, dust, grease-proof, and water resistant. In the case of a power failure, all SG1000s are designed to retain accurate gate position.
-
-
Product
Radius, Straight Shaft Bullet Nose, Alternate 0.78 (22.00) - 3.70 (105.00) General Purpose Probe
HPA-0J-1
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
Product
Marine Shaft Power Meter Systems
-
Datum’s Marine Shaft Power Meter Systems are developed to provide real time and ongoing power monitoring data on propulsion shafts, thrusters and diesel generators. These devices are commonly used for fuel economy monitoring and equipment maintenance planning programs and can be used in conjunction with our EEXI | ShaPoLi solution to keep vessel owners in line with the latest legislation.
-
Product
Shaft Measuring Gage with Dual Glass Linear Encoder
1100GX
-
The economical gaging system of the Model 1100-GX handles a wide variety of part lengths and configurations, resulting in fast, highly accurate measurements of cylindrical engine components. Whether it is needed for use in a lab setting or out on the shop floor, this rugged gage is adaptable to a wide variety of work environments. This versatile gage employs the latest technology in motion controls, signal processing and linear grating technology.
-
Product
Shaft Alignment
AT-200
-
Connectivity, mobile devices, cloud-based platform, apps are integrated in the AT-200 making it a tool for short response time between machine failures and corrective actions. The smart sensors use CCD technology for a superior measurement performance and precision alignment.
-
Product
Shaft Speed Switches
-
A speed switch senses rotating shaft speed, comparing it to one or more settable over/under/zero speed alarm trip-points. A shaft speed sensor detects magnets embedded in a shaft-mounted pulser wrap/disc. As the shaft rotates, the passing magnets are detected across an air-gap as pulses with frequency proportional to shaft RPM. When a conveyor belt or bucket elevator begins to slip the pulse frequency (shaft RPM) crosses to the alarm side of a trip-point threshold, a corresponding relay de-energizes, providing shutdown or alarm.
-
Product
Optical Shaft Measuring System
-
The measurements and shape of the shaft or rotating partsare measured in an overwhelmingly short time. In our lineup, we can handle inspection and automation during production processes, so we can contribute to increased productivity at your company.
-
Product
Prop Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary receiver. The Miniature Strain Gage Transmitter can be attached to strain gages adhered to your shaft in order to transmit shaft torque and thrust while the system is running.
-
-
-
Product
Shaft Voltage Tester™ Digital Oscilloscope
AEGIS®
-
Digital Oscilloscope and Multimeter with Conductive Microfiber Probe Tips. Is your motor safe from destructive shaft voltages? For the first time you can get all of the tools to find out in one place. The AEGIS® Shaft Voltage Tester™ Digital Oscilloscope bundle includes the AEGIS-OSC-9100 100 MHz digital osciloscope, shaft voltage probe tips, and a shaft grounding simulator. Armed with these tools, you can quickly and easily find whether your motors are at risk of premature bearing failure due to VFD-produced bearing currents.
-
Product
Synchro/Resolver to Digital Converters
-
Resolvers and synchros are transducers that convert the angular position and/or velocity of a rotating shaft to an electrical signal. Both deliver signals proportional to the sine and/or cosine of the shaft angle. A resolver-to-digital or synchro-to-digital converter converts these signals to a digital output corresponding to the shaft angle and/or velocity. ADI’s family of RDCs and SDCs offer solutions for these applications.
-
Product
Wind Speed Sensor/Anemometer
ENVIROMUX-WSS
-
Rugged anemometer. 3-cup rotor pressed on a stainless steel shaft. Reed switch and magnet providing one pulse per rotation. Rotor diameter: 5 inches. Speed range: ~ 3 mph to 125+ mph (~5 kph to over 200 kph). Rugged Delrin body with bronze and Rulon bushings. Flat aluminum mounting bracket with 2 holes. esigned to be mounted on top of a pole or bracket. 100 feet of exterior grade wire. Maximum cable length: 1000 ft (305m).
-
Product
XCITE 1300T Torsional Series
-
The Xcite 1300T Torsional Series of modal exciters provides pure torque input into structures for modal parameter estimation without the bending mode coupling effects present when linear excitation is applied through moment arms. These systems are used in structure borne noise tests of structures such as automotive and truck transmissions, prop shafts, axles, differentials, and torsional engine dampers.
-
Product
Quadrature Position & Rate Meter
-
Accepts low-level differential or single-ended 5 V logic level quadrature signals from shaft encoders to display scaled position or scaled rate. One, two or four transitions may be counted at a maximum combined rate of 250 kHz and be mathematically scaled to display in engineering units from -999,999 to +999,999. An analog output scaled to the display and relay outputs are optional.
-
Product
Open Optical Encoders
-
An optical encoder is an electromechanical device which produces an electrical signal output proportional to the linear displacement of a linear guide or the angular position of an input shaft.Open encoders are exposed and feature no external integrated enclosure. The advantages of open optical encoders include the effective elimination of backlash, shaft wind-up (torsion) and other mechanical hysteresis errors.A rotary open optical encoder consists of a position measurement readhead and an accurate rotary scale marked either on the periphery of a ring or on the face of a disc.The readhead measures position by optically sensing the regularly-spaced scale markings and outputs this information as an analogue or digital signal.The signal is subsequently converted into a position reading by a digital readout (DRO) or motion controller.
-
Product
ElectroMagnetic Detector
MP Series
-
MP-900/9000 are chiefly used in conjunction with a detector gear mounted onto a rotating shaft by bringing the detector into proximity to the gear so that the detector outputs frequency signal of which is proportional to the rotational speed. So various types are available including low-priced, general purpose, oil proof and heat resistant types that you can make a choice for your usage.Signal cables (except attached-cable types), extension cables and connectors are sold separately.
-
Product
Torque Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S manufacturers two type of Torque transducers 1. In-Line Rotating Torque Transducers with / without speed sensors 2. Reaction Type Torque Transducers.*Transducer ranges from 1 Kg-m to 600 Kg-m with various types like Flange mount, Hallow type, Shaft mount, etc.
-
Product
Laser Trackers
Radian Series
-
The smallest, lightest, most accurate laser measurement tool. API’s compact and rigid UNIBODY tracker design allows for shaft mounted motors, encoders and laser. The UNIBODY shaft mounted laser innovation minimizes Abbe offset errors, while also housing laser source, optics, camera and major head electronics in the center of the tracker body.
-
Product
General Purpose Probe
BT-1
-
BT-1 General Purpose Probe - Probably our best general purpose probe designed for temperature measurement of solids, liquids, gases and semi-solids. Welded stainless-stell shaft, plastic handle. Tip is .028'' diameter bent at right angle to probe to facilitate accurate surface measurements. Immersible. Maximum temperature 240°C, Time constant 0.15 Seconds. 5 foot lead. Not isolated.
-
Product
Magnet Wheels Pulse Generators
199SM / 198EM Magnet Wheels
-
Magnet wheels work with Electro-Sensors Hall Effect shaft speed sensors providing 120 alternating magnetic poles around the circumference of the 3.75" diameter. The 199SM models mount around shafts up to 3" in diameter and are secured with set screws (provided). The 198EM mounts on the end of a shaft with a 10-32 UNF screw (provided - requires center drilling and tapping the shaft).• Use with 906, 906B, 1101 and other Hall Effect, non-metallic-end-capped shaft speed sensors (consult factory)
-
Product
Rotating Telemetry Systems
2100B Series
-
Advanced Telemetrics International
Are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
Torque Sensors
-
In universities and industry, for basic research or quality assurance: Kistler torque sensors guarantee precise definition of the power and friction values of drives, transmissions and pumps. Strain gage technology (DMS) is a powerful solution for measurements on rotating shafts, and also for long-term dynamic and static measurements. Maximum precision, the most rigid structure possible and high temperature stability: thanks to these assets, DMS sensors can accomplish the most demanding tasks. Piezoelectric reaction torque sensors offer convincing features such as exceptional overload protection, high signal resolution and a wide frequency range. They are ideal for measurement tasks when conditions are difficult due to geometry, temperature range or dynamics.
