Optical Modules
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function DAQ PCI Express Cards
DAQe-2500 Series
-
ADLINK DAQe-2500 series are high-speed and high-performance analog output multi-function DAQ PCI EXpress cards. The devices are able to update up to 8-CH, 12-bit analog outputs simultaneously at sustaining 1 MS/s. The reference sources and the output polarities are programmable on per channel basis, combining with the multiplying DAC architecture, ADLINK DAQe-2500 series DAQ cards can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees the CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
780174-01
-
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
PXI 8 Slot BRIC Matrix, Solid State, 192x8, 1-Pole (6 sub-cards)
40-563B-121-192X8
-
The 40-563B-121-192x8 is an ultra high density 8-slot matrix module with 1-pole switching and is part of our range PXI BRIC matrices. They are available in 2, 4 or 8-slot sizes to suit high performance PXI switching requirements and are constructed using solid state switches.
-
Product
PXI 12-Slot BRIC Matrix, 546x12 1-Pole (13 sub-cards)
40-558-121-546X12
-
The 40-558-121-546x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI High Density Multiplexer, 4-Bank, 16-Channel, 1-Pole, Screened
40-610A-014
-
The 40-610A-014 is a screened 4-bank, 16-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
Thermocouple, Module, Receiver, 90 Series, 64 Position
510104133
-
Primary mating module 510108124. (May mate with other ITA modules, as well.) *Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
PXI RF Multiplexer, 5x SP4T, 1.3 GHz 75 Ω, Multiway Connector
40-755-205
-
The 40-755-205 is a 5xSP4T 75 Ω multiplexer and is part of a range of high density RF multiplexers available in 50 Ω and 75 Ω variants with up to 10xSP4T switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot.
-
Product
PXI 2-Slot BRIC Matrix, 64x16, 1 Pole (2 Sub-cards)
40-558-201-64x16
-
The 40-558-201-64x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 1.81kΩ
50-297-122
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Data Acquisition System
Pixie-16
-
The Pixie-16 is a data acquisition system for nuclear physics and other applications requiring coincident radiation detection with large number of channels.
-
Product
8GE+4G SFP Managed Ethernet Switch, -40~75℃
EKI-7712G-4FI
-
8 Gigabit ports + 4 SFP ports, SFP socket for Easy and Flexible Fiber Expansion, Redundancy: X-Ring Pro (ultra high-speed recovery time < 20 ms), RSTP/STP (802.1w/1D). IXM function enables fast deployment, Security: 802.1x (Port-Based, MD5/TLS/TTLS/PEAP Encryption), RADIUS.
-
Product
LXI High Density Dual 32x64 2A Matrix
60-552-011
-
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
PXI 12-Slot BRIC Matrix, 576x8 1-Pole (9 sub-cards)
40-558-121-576X8
-
The 40-558-121-576x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-126
-
The 40-297A-126 (PXI) and the 42-297A-126 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 26.7 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
-
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 102k
40-297-134
-
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Dual 8 to 1 RF Multiplexer 3GHz 50 Ohm SMB
40-874-002
-
The 40-874-002 is a 50 Ohm 8 to 1 RF multiplexer with 2 banks in a single PXI slot. It has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of this RF multiplexer has been minimized by careful attention to the mechanical and electrical design.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 11.4MΩ
50-298-153
-
The 50-298-153 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 8 Slot BRIC Solid State 128x8 1-Pole (4 sub-cards)
40-563A-121-128X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Vacuum, Module, ITA, 90 Series, 2 Port Positions, w/ M22.5x1.5 Tap
510108251
-
Primary mating module 510104260. (May mate with other Receiver modules, as well.)
-
Product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
-
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
PXI Flexible Microwave Module, Dual SP6T 26.5 GHz, Single SPDT 26.5 GHz, 50 Ω, SMA
40-890-003
-
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
Product
MXM GPU Expansion Module
MIC-75GF10
-
Support NVIDIA MXM GPU with whole system fanless designSupport up to 80W NVIDIA Quadro MXM 3.1 Type A/B form factor GPU1 x HDMI and 3 x DisplayPort 1.4a display outputOperating Temp. -10~50CSupport 1Grms Op. vibrationDual front removable 2.5" storage bay for easy swapIP40 fanless ruggedized compact size designMIC-7 Series compatible
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 1Ω to 470Ω
40-252-114
-
The 40-252-114 is a programmable resistor module with 2 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 395kΩ
40-251-142
-
The 40-251-142 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 395kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module
780030-01
-
24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.
-
Product
PXI 4 Slot BRIC 90x16 2-Pole (6 sub-cards)
40-561A-022-90X16
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, Terminated Common, 3GHz, 50Ω, SMB
42-876A-001
-
The 40-876A-001 (PXI) and 42-876A-001 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module exhibits low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI High Density Mux 99 Channel 1 pole
40-670A-021-99/1
-
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 62.5/125 Fiber, FC/PC Connectors
42-850A-114-M62.5
-
The 40/42-850A-114-M62.5 is a PXI/PXIe 4-channel multiplexer with FC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
