Phase Noise Analyzers
-
Product
Phase Noise Analyzers
-
The phase noise analyzer portfolio from Rohde & Schwarz offers an affordable, mid-range solution with high sensitivity and fast measurements as well as high-end ultra-high-sensitivity solutions with advanced measurements modes. Ideal for phase noise analysis and VCO tests, the industry-leading solutions enable two-path phase noise analysis with real-time cross correlation and fast VCO characterization with built-in low-noise DC sources. Additionally, high-end signal and spectrum analysis can be added into a single box.
-
Product
Phase Noise Analyzers
-
Holzworth Instrumentation, Inc.
Holzworth's Real Time Phase Noise Analyzers are each designed to provide data faster than any other system, while maintaining data accuracy and repeatibilty. There is no guess work as to whether results are valid to the DUT or if there are unwanted variations or contributions coming from the measurement system itself.
-
Product
Hi-Q W-Band Ultra Low Phase Noise Analyzer
OE8000W
-
HI-Q® W-Band phase noise test system utilizesmicrowave photonics techniques for automatedmeasurement of ultra-low phase noise W-bandoscillators.
-
Product
Phase Noise Analyzer and VCO Tester
FSPN
-
The R&S®FSPN phase noise analyzer and VCO tester is designed to provide both very high sensitivity and measurement speed for production and design engineers working in these fields characterizing sources such as synthesizers, VCOs, OCXOs, and DROs. It is the ideal instrument for demanding development and production phase noise and VCO analysis.
-
Product
Phase Noise Analyzer
NXA-26
-
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
Product
Phase Noise Generator / Calibrator
PNG-A
-
Noise eXtended Technologies S.A.S.
The PNG-A is a high precision generator used in Test and Measurement instruments calibration. It is a Signal Generator with precisely computed phase and amplitude noise characteristics. With its wide frequency offset range, 1Hz to 1 MHz offset, and its programmable Phase and Amplitude noise in real time, this is the ideal standard to calibrate phase noise analyzers, Signal Source Analyzers and Spectrum Analyzers.
-
Product
Phase Noise Analyzer
NXA-6
-
This new NXA-6 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 6 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range.
-
Product
Phase Noise Analyzer
DCNTS
-
Noise eXtended Technologies S.A.S.
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences.
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
-
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
RF Synthesizers Modules
-
Holzworth Instrumentation, Inc.
Holzworth's RF Synthesizers Modules were originally designed as the internal, tunable LO test sources for Holzworth phase noise analyzer products. Due to the need for easy integration, the HSM Series designs incorporate a long list of electrical and mechanical features to satisfy the demanding requirements of today's high performance communications systems and integrated test systems. FIELD PROVEN RELIABLITY with MTBFs exceeding 240kHrs.
-
Product
The All-In-One Noise Test System
NXA Series
-
Noise eXtended Technologies S.A.S.
The NXA is a fully automated Phase Noise analyzer. Its dual channel architecture allows the system to use a cross-correlation process to cancel its internal noise floor. This reliable technique provides access to the unique noise floor performance of the DCNTS.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 3.6 GHz
N8973B
-
The N8973B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8973B.
-
Product
Low-Noise Filter, 210 V / 3 A
N1298C
-
The N1298 Series power source accessories are a collection of low noise filters for the Keysight B2960 Series precision source / measure units (SMUs).
-
Product
Phase Angle Voltmeters
-
Since the development of the first Phase Angle Voltmeter (PAV) over 50 years ago, North Atlantic Industries has been the industry leader in AC Measurement Instrumentation. Our name has become synonymous with innovation and quality. Our products, specifically designed for defense, industrial, and commercial applications, deliver industry-leading accuracy, repeatability, and reliability.NAI’s units of today are actually multifunction Digital Analyzing Voltmeters that combine a complete Voltmeter, a Phase Angle Voltmeter, and a Waveform Signal Analyzer in a single microprocessor-based instrument. With these versatile and flexible instruments, a wide range of tests can be performed, either manually using the front panel controls or automatically using the IEEE-488 bus. Designed for the Synchro/Resolver and LVDT/RVDT marketplace, NAI’s Voltmeters are used in a variety of applications.
-
Product
Noise Source, 10 MHz to 18 GHz, nominal ENR 15 dB
346B
-
The Keysight 346B noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The 346B's high ENR, low SWR, and variety of connectors make it a general-purpose noise source. Add special option H01 for high ENR (21 dB typical) to measure high noise figure devices, or option H42 for measuring Direct Broadcast Satellite (DBS) low noise block converters.
-
Product
PCI Express 5.0 Protocol Exerciser/Analyzer
Summit Z58
-
The Summit Z58 is a PCIe 5.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z58 can emulate PCI Express 5.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
Product
Envision Analyzer & Generator
MIPI C-PHY/D-PHY
-
The Envision X14 Analyzer capture utility provides deep analysis for MIPI camera and display protocols over C-PHY and D-PHY layers. The X14 Analyzer can be positioned either as an endpoint to test a CSI-2 or DSI-2 stream or tapped in between a CSI-2 or DSI-2 device and host for passive monitoring and analysis. The Envision X14 ensures fast Time-to-Insight through its rich set of innovative features for debug analysis and identifying and resolving elusive protocol errors.
-
Product
High-speed Interconnect Analyzer, 4-port, S-par @40 GHz, <1 mm Res., 4 phase matched cables
WAVEPULSER-40iX
-
High-speed Interconnect Analyzer, 4-port, S-par @40 GHz, <1 mm Res., 4 phase matched cables.
-
Product
VHF/UHF Nav/Drone Analyzer
EVSD1000
-
The R&S®EVSD1000 VHF/UHF nav/drone analyzer is a signal level and modulation analyzer for use aboard medium sized drones. It measures ILS, GBAS and VOR ground stations during startup, maintenance and servicing and analyzes air traffic control communications (ATC COM) signals. The mechanical and electrical design is optimized for drone based measurements of terrestrial navigation systems.
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
-
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
Optical Modulation Analyzer
OMA
-
In partnership with Tektronix, we bring you a high-performing and flexible OMA system that will meet your requirements today and into the future.With the market-leading performance of Quantifi Photonics’ IQRX coherent receiver and the scalable architecture of Tektronix’s high-performing oscilloscopes, you’ll get the most out of your investment. Use the stack as a single 70GHz OMA system, or use it as four independent oscilloscopes.Whether you are working with 100G coherent transceivers or 1 Terabit long haul communication systems, our OMA can be configured to suit your exact requirements.
-
Product
Phase Angle Voltmeter, Industry Standard
2250A
-
NAI's 2250A Phase Angle Voltmeter is the most accurate and versatile AC measurement tool in the Synchro/Resolver and LVDT/RVDT marketplace. Considered the industry standard and based on the latest DSP and FPGA technologies, the 2250A substantially extends and simplifies the capabilities of the legacy 2250 model.
-
Product
Boundary-Scan Interactive Analyzer & Toolkit
ScanExpress JTAG Debugger
-
Test probe access is a luxury—modern electronic system design techniques such as blind and buried vias or ball-grid-array (BGA) devices guarantee limited signal access. Test points quickly reduce precious board real-estate and can even degrade performance. ScanExpress JTAG Debugger overcomes these limitations to provide the control and visibility necessary to quickly debug and test hardware, using a simple JTAG port to interface with IEEE-1149.1 compliant devices.Whether debugging prototype hardware, enhancing production tests with boundary-scan control, or diagnosing a faulty board in the field, ScanExpress Debugger’s easy-to-use and versatile interface helps engineers test and debug systems faster and more efficiently.
-
Product
Pocket-Sized Analyzer for Capturing & Decoding USB 2.0 Devices
Mercury T2C / T2P
-
The pocket-sized Mercury T2C & T2P capture and decode the widest range of USB 2.0 device classes plus Type-C link states and Power Delivery 3.0 messages. Both the Mercury T2C and T2P utilize the industry leading CATC Trace analysis software for verifying and debugging USB and PD protocol issues. Now there are two base models to choose from; the original Mercury T2C and the new Mercury T2P, which adds the Power Tracker graphical view of VBUS and CC voltages.
-
Product
26.5 GHz Single-Mode Lightwave Component Analyzer
N4375E
-
The new N4375E single-Mode LCA is based on the latest 5222A series network analyzers with 2-port or 4-port configuration. This LCA is the ideal measurement solution for electro-optical components up 26.5GHz electro-optical components, as well as Radio over Fiber (RoF) and aerospace and defense (A&D) electro-optical test applications. The N4375D is traceable to international standards and provides guaranteed specifications for electro-optical responsively S-parameter measurements in a turn-key solution. In combination with N4691B electronic calibration kit you get fastest setup of your test, so you can focus on developing your components. The new N4375D replaces the industry standard 8703A/B series and supports specified modulation frequencies up to 26.5 GHz at 1310nm and 1550nm source wavelength or individual wavelength with external optical input.
-
Product
TV Analyzer
ETL
-
The R&S®ETL TV Analyzer is an all-in-one solution. It combines the functionality of a TV and FM (radio) signal analyzer, a video and MPEG TS analyzer and a spectrum analyzer in a single instrument. The R&S®ETL also contains generators to create analog video signals, audio signals and MPEG-2 transport streams.
-
Product
UniPro/UFS Analyzer/Exerciser
Eclipse M52
-
Implementing a new high speed front end, supporting MIPI M-PHY™ HS-Gear5 at speeds up to 23Gbps, the Eclipse M52 stands as the markets most complete analyzer/exerciser. The Eclipse M52 is the right tool for engineers and developers who need to ensure the correct and efficient operation of technologies employing the high data transfer speeds of the UniPro/UFS specifications.
-
Product
Motor Drive Analyzer, 350 MHz, 8 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch
MDA 8038HD
-
Static power analysis - like a dedicated power analyzer.Dynamic power analysis – capture more information.Complete test coverage – control system, power section, motor.Comprehensive mechanical interface.Harmonics calculation option.Vector display option (THREEPHASEVECTOR).Waveform Transformations option (THREEPHASEdq0).16 Channels with OscilloSYNC™.
-
Product
SNS Series Noise Source 10 MHz to 26.5 GHz (ENR 15 dB)
N4002A
-
The SNS series N4002A noise source was designed to measure DUT noise figures reliably and accurately up to 30 dB from 10 MHz to 26.5 GHz.
