Precision Current Sources
-
Product
High Current Probes (Battery Contacting) HC200C06G72NTC
1034017
-
The High Current Probes (Battery Contacting) HC200C06G72NTC, order code 1034017, are engineered to deliver robust performance across various demanding applications. Designed with a coaxial probe configuration, these probes boast an impressive continuous current capacity of 300 A, making them ideal for high-load environments. With an operating temperature range of -45°C to +200°C, they maintain reliability under extreme conditions, ensuring that precision and performance are never compromised.
-
Product
Primary & Secondary Current Injection Testing Sets
-
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
Product
Leakage Current Monitor
-
To alert utility-line workers of overcurrent conditions on such aerial devices as insulated ladders and truck booms, the Chance Sentinel sounds an alarm if leakage current reaches a pre-set level.
-
Product
High Precision Digital 10A Mirco-Ohmmeter
DRM-10A™
-
The DRM-10A™ is a lightweight and portable micro-ohmmeter designed to measure very low resistances from 0.01 μΩ to 200 Ω. It is the most accurate in its category.
-
Product
Direct Current Measurement Card
LQI5
-
Computer Gesteuerte Systeme GmbH
The LQI5 is a precision direct current measurement card. It features 6 measurement ranges for unipolar current measurements of up to 32 A. Current pulses shorter than 5 seconds can be measured up to 65 A.
-
Product
High Current Probe HCF77255B200G300
1016555
-
The HCF77255B200G300 High Current Probe is meticulously engineered for power electronics applications, boasting a robust design that ensures exemplary performance in challenging environments. Capable of operating at temperatures ranging from -45°C to +200°C, this probe is ideal for high-stakes precision measurements. Its durable construction incorporates beryllium copper for the plunger, coupled with gold plating to enhance conductivity and minimize contact resistance, which is maintained at a typical rate of just 10 mOhm.
-
Product
Through Hole Type AC Current Sensor
CTF-400B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Suitable for current measurements of main cable.*Measuring range:AC 1A～400A.
-
Product
High Precision Compression Type Load Cell
HR II
-
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
Product
Current Caliper
KH23101
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
Product
High Power Programmable AC Source with Transients
61510
-
Chroma Systems Solutions, Inc.
Power Rating:61511: 12KVA61512: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
Product
Standard Round 2m Cables, Shielded, for Higher Current
ST010-S
-
Connection to digital boards, intended for higher currents. to be used with CPCI-1500, APCI-1500, APCI-1564, APCI-2032.
-
Product
High Current Probes (Battery Contacting) HC200D06G73NTCF
1125168
-
The High Current Probes (Battery Contacting) HC200D06G73NTCF are designed for high-performance applications, accommodating temperature ranges from -45°C to +200°C. These probes feature a robust construction and advanced materials, ensuring reliable performance even under extreme conditions. The continuous current handling capacity is rated at 300.00 A, with a typical contact resistance of only 0.20 mOhm, making them highly efficient for various electrical applications.
-
Product
Split type AC Current Transformer
CTF-200T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*1A output for metering application.*Wire stopper is equipped for the slipping protection.*The special connector is not necessary as the output terminals are provided.*Open circuit protection and nonflammable plastic material.
-
Product
Precise Timing
-
Schweitzer Engineering Laboratories, Inc.
Precise timing is achieved using satellite clocks, which process signals from Global Navigation Satellite Systems, such as GPS, and output time to power system devices using IRIG-B, the Precision Time Protocol (PTP), and the Network Time Protocol (NTP).
-
Product
Directional Source
BAS003
-
The BAS003 Source is designed to generate homogeneous sound fields using random noise in compliance with the following standards: Building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-3, ASTM E90, ISO 140-5, ASTM E966). The BAS003 is typically used to generate a noise in a free-field for the evaluation of the transmission loss index of a façade. The available high-efficiency power amplifier, BAS002, is light and can be remotely controlled for easy use in the field.
-
Product
PXI Precision Resistor Module 3-Channel, 2.5 to 773k
40-297-143
Programmable Resistor Modules
This 3-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
SparkFun Current Sensor Breakout
ACS723
-
The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
AC/DC Current Clamp Meter
CM600
-
Clamp opens up to 1 inch (25.4 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 600 Volt. AC/DC current measurement up to 600 A.Relative measurement. One touch auto zero.
-
Product
Calibration Sources
-
Up to an absolute accuracy of 60 MHz standard HighFinesse Wavelength Meters feature auto-calibration by integrated calibration sources. This way highest accuracy and stability of measurements with our wavemeters is guaranteed.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-155
Precision Resistor Module
The 40-297A-155 (PXI) and the 42-297A-155 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 43.8 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Portable Light Sources
FOD 2113
-
The FOD 2113 provides three wavelengths: 1310&1550 nm in one port and 850 nm 10mW in another port. Available adapter types: FC, SC, ST, Universal 2.5mm. All adapters are changeable
-
Product
High Current Probes (Battery Contacting) HCF73306B300G600
1000793
-
The High Current Probes (Battery Contacting) HCF73306B300G600, order code 1000793, are specialized components designed to deliver high precision and reliability in electrical measuring applications. Engineered to operate effectively under a temperature range of -45°C to +200°C, these probes are ideal for demanding environments. Their basic contact probe design features a pitch size of 4.00 mm (157 mil), making them exceptionally suited for a variety of applications requiring accurate and efficient electrical contact.
-
Product
Precision Coating Thickness Gauge Probe Range
Elcometer 355
-
Unique probe modules allow the Elcometer 355 Coating Thickness Gauge to be versatile and flexible for any coating thickness measurement application.
-
Product
Digital Ior Leakage Current Clamp Tester
MCL-400IR+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
Product
Rack Type Light Source
JW8007
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Rack type light source is a new instrument with high output stability and good wavelength stability, which is developed by Joinwit Company using automatic optical power control (APC) technology and automatic temperature control (ATC) technology. It is an ideal instrument for measuring optical device characteristics, device aging, monitoring, experiment and other application fields in many optical device manufacturers, scientific research institutes and colleges and universities in the field of measuring optical device characteristics, device aging, monitoring and experiment. It is simple in application and design, easy to use and maintain, and widely used in the fields of optical communication, optical transmission, optical fiber sensing and other fields such as scientific research, production and engineering.
-
Product
Light Sources
-
Excelitas offers an array of illumination and lighting technologies with custom design capabilities aligned with customer requirements to deliver an illumination solution optimized to your specifications. From simply supplying a discrete LED, Laser, Lamp or UVC source to providing a complete, integrated system, Excelitas consistently delivers lighting solutions for the most demanding applications.
-
Product
High Current Probes (Battery Contacting) HC200D06G73PT1000CF
1125162
-
The High Current Probes (Battery Contacting) HC200D06G73PT1000CF, identified by the order code 1125162, is engineered for high-performance applications requiring robust interfacing with battery connections. This basic contact probe is designed with precision to handle continuous currents up to 300 A, making it ideal for demanding environments. Its operational temperature range of -45°C to +200°C ensures reliability in extreme conditions, while the typical contact resistance of just 0.20 mOhm guarantees minimal energy loss during operation, enhancing the efficiency of any battery-driven system.
-
Product
Quality Control for more Precision in Press Hardening
PRESS-CHECK
-
The automated test system PRESS-CHECK works with two powerful high-end thermographic cameras for continuous measurement of two-dimensional temperature distribution. This measurement is carried out before the pressing operation on the surfaces of the boards to be processed and subsequently on the resulting molded parts, ultimately enabling exact compliance with the thermal process parameters.
-
Product
Remote Plasma Sources For Process Applications
-
MKS remote plasma sources deliver high density reactive radicals improving on-wafer cleaning and deposition throughput. Solutions consist of a fully integrated, self-contained unit designed for quick on-chamber installation providing fast, reliable plasma ignition of O2, Hydrogen and Nitrogen gases in a customer configurable package. All solutions are equipped with intelligent power control and EtherCAT® diagnostics supporting Industry 4.0.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-046
Precision Resistor Module
The 40-297A-046 (PXI) and the 42-297A-046 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 5.82 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
